You are on page 1of 8

CCNA 3 Chapter 1 2011 V4.

0 Answers 100%
June 11, 2011 by admin · 7 Comments

CCNA 3 Chapter 1 2011 V4.0 Answers 100% 1. Which layer of the hierarchical network design model is refered to as the high-speed backbone of the internetwork, where high availability and redundancy are critical? access layer core layer data-link layer distribution layer network layer physical layer 2. Which two characteristics are associated with enterprise level switches? (Choose two.) low port density high forwarding rate high latency level support link aggregation predefined number of ports 3. Which feature supports higher throughput in switched networks by combining multiple switch ports? convergence redundant links link aggregation network diameter 4. Which hierarchical design model layer controls the flow of network traffic using policies and delineates broadcast domains by performing routing functions between virtual LANs (VLANs)? application access

QoS issues are greatly reduced. a network engineer is designing a new security structure for the network. Refer to the exhibit. There is less bandwidth competition between voice and video streams. The Ethernet VLAN structure is less complex. Configure port security options on S1. Which set of policies adheres to the hierarchical network model design principles? Implement Layer 3 switching on S1 to reduce the packet processing load on D1 and D2. Use Layer 3 access control features on D1 and D2 . What is the likely impact of moving a conventional company architecture to a completely converged network? Local analog phone service can be completely outsourced to cost-effective providers.distribution network core 5. A shared infrastructure is created resulting in a single network to manage. Install all security processing on S1 to reduce network traffic load. 6. Beginning with HR servers and workstations.

) Power over Ethernet load balancing across redundant trunk links redundant components Quality of Service link aggregation 11. Perform all port access and Layer 3 security functions on C1. Configuring communication between devices on different VLANs requires the use of which layer of the OSI model? Layer 1 Layer 3 Layer 4 Layer 5 9. the technician makes recommendations for adding new switches where needed and replacing existing equipment that . Which two features are supported at all three levels of the Cisco threelayer hierarchical model? (Choose two. Which layer of the OSI model does an access layer LAN switch use to make a forwarding decision? Layer 1 Layer 2 Layer 3 Layer 4 10. Move all HR assets out of the data center and connect them to S1. 7. Following this examination. Which three features are commonly supported at the distribution layer of the Cisco hierarchical network model? (Choose three.to limit access to the HR servers to just the HR subnet.) security policies Power over Ethernet switch port security quality of service Layer 3 functionality end user access to network 8. Use Layer 3 security functions on S1 to deny all traffic into and out of S1. A network technician is asked to examine an existing switched network.

hampers performance. Which two pieces of information would be helpful in determining necessary port density for new switches? (Choose two. A network administrator is selecting a switch that will operate at the network core. At which heirarchical layer are switches normally not required to process all ports at wire speed? core layer distribution layer access layer entry layer 14. Which three features should the switch support for optimum network performance and reliability? (Choose three.) forwarding rate traffic flow analysis expected future growth number of required core connections number of hubs that are needed in the access layer to increase performance 12. what functionality should be enabled at all three layers of the hierarchical network? Power over Ethernet quality of service switch port security inter-VLAN routing 15. The technician is given a budget and asked to proceed.) port security security policies 10 Gigabit Ethernet . For organizations that are implementing a voice over IP solution. Which hierarchical design characteristic would be recommended at both the core and distribution layers to protect the network in the case of a route failure? PoE redundancy aggregation access lists 13.

Which explanation accurately describes StackWise technology? StackWise technology allows up to eight ports to be bound together to increase available bandwidth.quality of service (QoS) hot-swappable hardware Power over Ethernet (PoE) 16. . Which layer of the hierarchical design model provides a means of connecting devices to the network and controlling which devices are allowed to communicate on the network? application access distribution network core 19. and core 17. 20. What statement best describes a modular switch? a slim-line chassis allows interconnection of switches on redundant backplane defined physical characteristics flexible characteristics 18. A technician is attempting to explain Cisco StackWise technology to a client that is setting up three stackable switches. StackWise technology allows the switch to deliver power to end devices by using existing Ethernet cabling. distribution. Link aggregation should be implemented at which layer of the hierarchical network? core only distribution and core access and distribution access. StackWise technology allows the switch capabilities and ports to be expanded by the addition of line cards. StackWise technology allows up to nine switches to be interconnected via the use of a fully redundant backplane.

2011 at 2:46 am . CCNA Exploration 3 Module 1 Exam Answers. CCNA Exploration 3 Chapter 1 Answers. abel says: June 12.Refer to the exhibit. CCNA Module 1 Answers. CCNA3 Chapter1. What characteristic of hierarchical network designs is exhibited by having SW3 connected to both SW1 and Sw2? scalability security redundancy maintainability Filed Under: CCNA 3 Exam Answers · Tagged With: ccna 3. Cisco CCNA 3 Chapter 1 Exam Answers. LAN Switching and Wireless Chapter 1 Answers Comments 1. CCNA 3 Module 1 Answers 2010.

m very happy with the knowledge you are sending me and i like except my problem still bremains funds for exam registration. Joseph says: September 1. otherwise i will be able to revise your notes and study them until i get funds for registration Reply 2. Link aggregation should be implemented at which layer of the hierarchical network? Shouldnt the answer is Access distribution and core? Reply o Tom says: September 10.i. 2011 at 12:28 pm Yes it should be access distribution and core that’s the correct reply Reply 3. regarding your CCNA 3 chapter 1 question 16. tony says: . 2011 at 7:19 am Hi.

4 “access.. The correct answer is option No. pOGISO LenamilE CatlasS says: February 18. 2011 at 11:37 am me ta thy qito teste kur tu koqitet dikun e qel kta edhe testin e ki 90 % te krym ( this is in albanish ) Reply 4. Reply 5. hussein says: May 9.September 24.I get 95% . 2012 at 6:21 am answer No. 16 is not correct ... 2012 at 3:34 pm this is super. anyway thanks. oooh no its in-fact superb no one will ever fail unless otherwise you don’t take your life serious .thiz is wow with cisco. and core”. distribution. Reply .guys keep on hitting us with the staff we are tired of reading thousands of pages looking for things which could be eased like these.