You are on page 1of 26

COMPACT PDH

NETWORK MANAGEMENT

User Manual

NMS User Manual

Page 2 of 26

1. Summary
NMS management system is used for managing PDH devices, it has network management functions of enquiry alarm, performance and data configuration.  System request Microsoft Windows TM NT/2000 series operating system; CPU of above Pentium TM II350; EMS memory of above 256MB; Display resolution of 1024×768; Harddisk of above 10Gb spare capacity.  Software installation NMS software installation is very simple, user only needs to find installation file setup.exe,and then install according to the clews.

2. Communication mode of network management
NMS network management system can manage multi units of PDH in multi-network.

2.1 Short-range management
PDH devices only offer one kind of network management port: serial port. If there is only ETH in external environment, you can use virtual serial card. PDH can support 16 serial ports at most.

Serial Network Management method

2 Remote management Remote management means that NMS and device is not at the same place. NMS manages PDH device through ETH、common telephone line or DDN. such as followed pictures: .NMS User Manual Page 3 of 26 Serial virtual ETH Network Management method 2.

NMS User Manual Page 4 of 26 Serial virtual ETH remote method Serial remote method (centralized) PDH (veneer) devices can use virtual serial card to extend serial port to device through ETH .

Basic operation 3.1.1 Login in the system In default mode: Username is null Password is null 3.1 Main interface .NMS User Manual Page 5 of 26 3.

2 Modify the Username .1.NMS User Manual Page 6 of 26 3.

3 Change the Password Enter old Password. Use the new Username and Password to login the system. .NMS User Manual Page 7 of 26 Enter the old Username. the Password change successful. new Password and confirm Password When follow picture is show.1. 3. the Username modified successful. old Password and New Username When follow picture is show.

2 Enter the main interface 3. there will be followed dialog box. If using keyboard. click “Add Subnet”. Click right key of mouse. Note: you can add multi Subnet at the same time in NMS . there will be dialog box of adding subnet.NMS User Manual Page 8 of 26 3. the navigating menu is blank. there will be pull-down menu of adding subnet. please press “Add” directly.3 Add subnet When PDH is running for the first time.

and there will be dialog box of successful operation. Use the “Add Description”to describe the Subnet Enter the description .NMS User Manual Page 9 of 26 Input subnet name directly in the dialog box. subnet will be added. after clicking “Add Subnet” or press ENTER.

NMS User Manual Page 10 of 26 Show the Network Property .

NMS User Manual Page 11 of 26 3. the device view in NMS will be show. . there will be pulldown menu. click right key of mouse. After click the “Add”. can add multi –Ne in one Subnet.4 Add network element Select subnet which has been added. that is. Then choose the device type and set the Ne Name in this interface. and click the left key “Add ne”. there will be the interface of adding network element. in one Subnet can add multi units of devices. in this interface will introduce the each device.

NMS User Manual Page 12 of 26 3.5 Modify the Ne Name and Add Description Modify the Ne name Enter the new Ne Name Then the Ne Name in NMS system will show .

NMS User Manual Page 13 of 26 Add the description of Ne Enter the description in the follow interface .

NMS User Manual Page 14 of 26 Show the Ne Property The view will show the information of Ne .

6 Set the Link property of network element Select network element which has been added. .NMS User Manual Page 15 of 26 3. click “Connect” button in the view. there will be pull-down menu. Then the system will show . and choose which serials port is available in PC which connect to the PDH through the console cable.

the NMS system will show the state of PDH. The green LED in the panel means the state normal. The red LED in the panel means alarm.NMS User Manual Page 16 of 26 When the PDH has connected the NMS system. If there is any alarm in current PDH the Ne will show red .

7 Network element-management 3. but need “Download” to device. through clicking Apply button.1 Button in the NMS system Save: save current settings into system. they are stored to FLASH memorizer.7 . . the configuring data can be sent down to device through clicking Download button. at this time data hasn’t been sent down to device. 3. then setting can become effective. can use for setting of other devices. and the working mode of device is changed according to the newest configuring data. Exit: exit the network management system.7.NMS User Manual Page 17 of 26 3. Download: after data of network manager interface is configured. Upload: Upload the newest network manager data which is stored in FLASH memorizer. Default: resume the default value configured by interface.2 Alarm information in the NMS system Click the “Local Alarm” button can check the local alarm. After the device receives the newest configuring data. the default data can be sent down to device. and show them through network manager interface.

. Port-base VLAN.1Q Tag VLAN. 802. E1 and Ethernet port in the device. 3. can configure the device. can set the Port Separation.3 Configure the device Click the “Config” button. In this interface. Special Tagging.7.NMS User Manual Page 18 of 26 Click the “Remote Alarm” button can check the remote alarm.

3 . It can use add the Tag ID in the network.NMS User Manual Page 19 of 26 3. LAN2. each ETH port is set to be 1 special Tagging. each PDH can be set to be 4 special Tagging at most. It will add a Tagging on the ETH packet which had set the 802.7. can set VLAN ID of 1-4095.1Q VLAN Tag.1 Special Tagging Special Tagging is a private protocol. . but never effect the VLAN ID in the switch which connect to the ETH port of PDH. the each LAN. Like follow: In the Special Tagging mode. the LAN1. It can separate the 4ETH port in the PDH base on Tag. In the NMS system. LAN3. LAN4 can’t communication each other.

Set LAN 3 and WAN to belong to VLAN3.3 .2 802.7. Set LAN 1 and WAN to belong to VLAN 1. Set LAN 4 and WAN to belong to VLAN 4.1Q tag VLAN For example As above picture. Set LAN 2 and WAN to belong to VLAN 2. . User A4 only can communicate with User B4. Add 5 records in VLAN table. Set LAN 1、LAN 2、LAN 3、LAN 4 and WAN to belong to VLAN 5. User A1 only can communicate with User B1. User A2 only can communicate with User B2.NMS User Manual Page 20 of 26 3. User A3 only can communicate with User B3.

.NMS User Manual Page 21 of 26 Set PVID of LAN 1 to be 1. Set PVID of WAN to be 5. Set PVID of LAN 3 to be 3. Set PVID of LAN 4 to be 4. Set PVID of LAN 2 to be 2.

1q Tag VLAN”.NMS User Manual Page 22 of 26 Port Separate is set to be “Disable”,VLAN Mode is set to be “IEEE 802.1q Tag”of WAN port to be VLAN Tag“Insertion”. . At the same time need to set “802.

NMS User Manual Page 23 of 26 Then click the “Download” Click the OK. the configuration is downloaded to the device. .

Rate Limitation: take 32kbps as step-size to adjust port rate. “Disable” shows to disable restrain function of ETH Broadcast Storm. 3. 802. value rang is 0~3200.3 X Pause Enable and Disable. insert VLAN ID which is default in input port in the data packet. don’t make any changes. this port forwards all ETH Broadcast packet. which connects remote device through optical port. Attribute configuration of each ETH port includes 802. this port only allows 1% of ETH Broadcast packet to pass. Port Forwarding:“Enable” shows to enable Port Forwarding of ETH port. including LAN port 1. Broadcast Storm Protection:“Enable” shows to enable restrain function of ETH Broadcast Storm. if without Tag. “Remove” shows to remove Tag. 802. if without Tag. .1Q tag Insertion and Removal. don’t make any changes. Port Rate Limitation based on 32kbps (speed range is 0~100M). “Disable” shows to disable PAUSE of ETH port. 802. Speed and Duplex configuration of each ETH port. when the data packet which is output from this port has been with Tag. remove this Tag. WAN port is inner port of device.NMS User Manual Page 24 of 26 3. Port Forwarding Enable and Disable. 4 Set the ETH Port This interface is used for configuring attribute of each ETH port. 2. 4 and one WAN port. Broadcast Storm Protection Enable and Disable. when the data packet which is output from this port has been with Tag. “Disable” shows to disable Port Forwarding of ETH port.1q Tag: “Insert” shows to insert Tag.3X: “Enable” shows to enable PAUSE of ETH port. LAN port shows 4 ETH ports offered by device.7.

7. . 5 Set the E1 Channel In “E1 Channel” view. can set each E1 channel as “No Loop”. which is easy to test and manage estate of each E1 channel. “Local Loop” or “Remote Loop”. force 10M half-duplex. also can set loop estate of each E1 channel.NMS User Manual Page 25 of 26 Speed and Duplex:can be separately set to be AUTO. force 10M full-duplex. forced 100M half-duplex. 3. forced 100M full-duplex. can check the estate of each E1 of device.

Use of button“Disconnect”is to disconnect RS232 connection of NMS system and device.8 Status of the device This view mainly shows the working estate of current device.9 Disconnect the device. 3.NMS User Manual Page 26 of 26 3. .