You are on page 1of 7

Exam : Title

:

Cisco 640-802
Cisco Certified Network Associate

Update :

Demo

B. Ltd. Answer: AD 2. The bandwidth is set too low. It has been replaced with a Cisco Catalyst 2950 series switch. A Layer 1 problem exists. Assume that all of the router interfaces are operational and configured correctly. Lower the root path cost on the switch ports. . What could be possible causes for the "Serial0/0 is down" interface status? (Choose two. How will router R2 be affected by the configuration of R1 that is shown in the exhibit? | English | Chinese | Japan | Korean | -2- Test Information Co. Increase the VTP revision number for the domain. There is an incorrect IP address on the Serial 0/0 interface. E.. Lower the bridge priority number. What must be done to ensure that this new switch becomes the root bridge on the network? A. Refer to the exhibit. C. D. The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning.1. Change the MAC address of the switch. B.) A. A protocol mismatch exists. E. Answer: A 3. C. An incorrect cable is being used. Refer to the exhibit. Assign the switch an IP address with the lowest value. All rights reserved. D.

from R1. 66.A. R2 will not have a route for the directly connected serial network. Ltd.. Router R2 will obtain a full routing table. Answer: A 4. Router R2 will not form a neighbor relationship with R1.15.32.55. C. 17. the amount of available flash and RAM memory C. All rights reserved. R2 will obtain OSPF updates from R1. as well as the two Ethernet networks connected to R1.64. Which three IP addresses can be assigned to hosts if the subnet mask is /27 and subnet zero is usable? (Choose three.1 D.128.) A. but will not obtain a default route from R1. the version of the bootstrap software present on the router D. but all other directly connected networks will be present.17 B. . Before installing a new.66. 10.1. B. what should be checked on the router.128 C. show version E. show running-config Answer: BD 5. and which command should be used to gather this information? (Choose two.) A. show processes F.15. 135. D.34 | English | Chinese | Japan | Korean | -3- Test Information Co. including a default route. upgraded version of the IOS. the amount of available ROM B.

B.1. Refer to the exhibit.192. 129.63 Answer: ACD 6.192 F. All rights reserved. Refer to the exhibit.33. Ltd. A packet with a source IP address of 192.E. Answer: D 7.5.168. F.2.1.4 and a destination IP address of 10. D. which entry will be in the ARP cache of HostA to support this transmission? A. After HostA pings HostB. 192. What action does the router take? | English | Chinese | Japan | Korean | -4- Test Information Co. C. E.. .168.4 arrives at the HokesB router.

A. Refer to the exhibit. Router1 and Switch2 should be connected via a crossover cable. D.0. Which two statements are true about the loopback address that is configured on RouterB? (Choose two. forwards a packet containing an ICMP message out the FastEthernet0/0 interface D. forwards a packet containing an ARP request out the FastEthernet0/1 interface Answer: C 8. B. forwards the received packet out the Serial0/0 interface B. Router1 will not play a role in communications between host A and host D. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit. Answer: DF 9. It decreases the metric for routes that are advertised from RouterB..) A. C. forwards a packet containing an EIGRP advertisement out the Serial0/1 interface C. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two. B. . The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces. The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using the same encapsulation type. F.1. | English | Chinese | Japan | Korean | -5Test Information Co.0. E.) A. Ltd. Refer to the exhibit. It provides stability for the OSPF process on RouterB. D. Host E and host F use the same IP gateway address. C. It specifies that the router ID for RouterB should be 10. It ensures that data will be forwarded by RouterB. All rights reserved.

E. C. A network administrator is explaining VTP configuration to a new technician.E. . All rights reserved. Answer: BC 10.. F. D. A switch in the VTP client mode cannot update its local VLAN database. A switch in the VTP transparent mode will forward updates that it receives to other switches. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number. A trunk link must be configured between the switches to forward VTP updates. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership. It indicates that RouterB should be elected the DR for the LAN.) A. B. Ltd. What should the network administrator tell the new technician about VTP configuration? (Choose three. A switch in the VTP server mode can update a switch in the VTP transparent mode. Answer: ABD | English | Chinese | Japan | Korean | -6- Test Information Co.

The safer.com . We provide high quality IT Certification exams practice questions and answers(Q&A).easier way to help you pass any IT Certification exams . And help you pass any IT Certification exams at the first try. Customer Support : support@exam.We was founded in 2006.