You are on page 1of 108

 

TestGuide4U (ExamGuidesForIT) 
More Exams Can be Purchased through Credit Cards or Paypal Online Directly.
Download link will be sent to your email immediately after the purchase.

Check Out Our Site at:  
www.e-junkie.com\TestGuide4u
 

 

Exam A

QUESTION 1

A network administrator executes the command clear ip route. Which two tables does this command clear
and rebuild? (Choose two.)

A. IP routing
B. FIB
C. ARP cache
D. MAC address table
E. Cisco Express Fonrvarding table
F. topology table

Answer: AB
Explanation/Reference:

QUESTION 2

Under which condition does UDP dominance occur?

A. when TCP traffic is in the same class as UDP
B. when UDP flows are assigned a lower priority queue
C. when WRED is enabled
D. when ACLs are in place to block TCP traffic

Answer: A
Explanation/Reference:

QUESTION 3

Which method allows IPv4 and IPv6 to work together without requiring both to be used for a single

connection during the migration process?

A. dual-stack method
B. 6to4 tunneling
C. GRE tunneling
D. NAT-PT

Answer: A
Explanation/Reference:

QUESTION 4

Which switching method is used when entries are present in the output of the command show ip cache?

A. fast switching
B. process switching
C. Cisco Express Fon/varding switching
D. cut-through packet switching

Answer: A
Explanation/Reference:

QUESTION 5

Refer to the exhibit.

A network administrator checks this adjacency table on a router. Execute the command ip tcp window-size 65536. MTU window Answer: BCD Explanation/Reference: QUESTION 7 Which two actions must you perform to enable and use window scaling on a router? (Choose two.) A. explicit congestion notification C. header compression B. C. . incomplete ARP information B. Set window scaling to be used on the remote host. What is a possible cause for the incomplete marking? A. Execute the command ip tcp queuemax. dynamic routing protocol failure D.) A. time stamps E. serial link congestion Answer: A Explanation/Reference: QUESTION 6 Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three. B. TCP path discovery F. keepalive D. incorrect ACL C.

Which UDP characteristic does this scenario describe? A. nonsequencing unordered packets E. Set TCP options to "enabIed" on the remote host. Tunneling does not enable users of the new protocol to communicate with users of the old protocol without dual-stack hosts. starvation C. Answer: C Explanation/Reference: QUESTION 9 A network administrator uses IP SLA to measure UDP performance and notices that packets on one router have a higher one-way delay compared to the opposite direction. Tunneling destinations are manually determined by the IPv4 address in the low-order 32 bits of IPv4-compatible IPv6 addresses. connectionless communication D. latency B. E. jitter Answer: A Explanation/Reference: . Tunneling is more difficult to configure than dual stack or translation. Answer: AB Explanation/Reference: QUESTION 8 Which statement about the use of tunneling to migrate to IPv6 is true? A. Tunneling is less secure than dual stack or translation. Execute the command ip tcp adjust-mss. B.D. C. D.

random early detection D.QUESTION 10 A network engineer notices that transmission rates of senders of TCP traffic sharply increase and decrease simultaneously during periods of congestion. queue management algorithm Answer: A Explanation/Reference: QUESTION 11 Which three problems result from application mixing of UDP and TCP streams within a network with no QoS? (Choose three. starvation B. jitter C. global synchronization B. lower throughput Answer: ACE Explanation/Reference: QUESTION 12 Refer to the exhibit.) A. Which condition causes this? A. . tail drop C. windowing E. latency D.

Frame Relay broadcast queue D. C. The router will listen for all multicast traffic.1. Frame Relay inverse ARP B.1. which statement is correct? A. There is no default gateway.201. Answer: C Explanation/Reference: QUESTION 13 Which protocol uses dynamic address mapping to request the next-hop protocol address for a specific connection? A. B.Based on this FIB table. dynamic DLCI mapping . D.168.168. static DLCI mapping C. The gateway of last resort is 192. The IP address of the router on FastEthernet is 209.201.

Active Authentication Phase and PPP Session Phase B. Enable QoS FIFO for PPPoE support. Which feature can be used to accomplish this task? A. B. Answer: B Explanation/Reference: QUESTION 16 A corporate policy requires PPPoE to be enabled and to maintain a connection with the ISP. Disable CDP on the interface. TCP Adjust . even if no interesting traffic exists. C. Active Discovery Phase and PPP Session Phase Answer: D Explanation/Reference: QUESTION 15 Prior to enabling PPPoE in a virtual private dialup network group. D. Execute the no switchport command. Active Authorization Phase and PPP Session Phase D. Passive Discovery Phase and PPP Session Phase C. which task must be completed? A.Answer: A Explanation/Reference: QUESTION 14 PPPoE is composed of which two phases? A. Execute the vpdn enable command.

Dialer Persistent C. Answer: D Explanation/Reference: QUESTION 18 A network engineer has been asked to ensure that the PPPoE connection is established and authenticated using an encrypted password. PPPoE functions as a Layer 2 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers. Once the link setup is completed. PAP . PPPoE Groups D. PPP options are not negotiated and authentication is performed. half-bridging E. PPP options are automatically enabled and authorization is performed. Which technology. PPP options are negotiated and authentication is performed. PPPoE functions as a Layer 3 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers. B. in combination with PPPoE. Once the link setup is completed. PPPoE functions as a Layer 2 encapsulation method that allows data to be encrypted over the PPP link within PPPoE headers. D. Once the link setup is completed. PPPoE functions as a Layer 4 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.B. PPP options are negotiated and authentication is not performed. Once the link setup is completed. C. can be used for authentication in this manner? A. Peer Neighbor Route Answer: B Explanation/Reference: QUESTION 17 Which statement is true about the PPP Session Phase of PPPoE? A.

Why is the routing information not being learned by Router B? A. dot1x C. D. An IPv6 traffic filter is blocking the networks from being learned via the Router B interface that is connected to Router A. Answer: D Explanation/Reference: . IPsec D. the message "not a router" is found in the output. The networks that are advertised from Router A do not show up in Router B's routing table. C. CDPCP C. OSPFv3 timers were adjusted for fast convergence.B. B. PAP Answer: D Explanation/Reference: QUESTION 20 Router A and Router B are configured with IPv6 addressing and basic routing capabilities using OSPFv3. The networks were not advertised properly under the OSPFv3 process. CHAP E. CHAP D. IPv6 unicast routing is not enabled on Router A or Router B. After debugging IPv6 packets. ESP Answer: D Explanation/Reference: QUESTION 19 Which PPP authentication method sends authentication information in clear text? A. NIS CHAP B.

R4 has been added to the existing OSPF network to provide the interconnect between the OSPF and EIGRP networks. All traffic must use the shortest path that provides the greatest bandwidth. One network is using OSPF as its IGP and the other is using EIGRP as its IGP.16. A previous network engineer has started the merger implementation and has successfully assigned and verified all IP addressing and basic IGP routing. .QUESTION 21 You are a network engineer with ROUTE. The redundant paths from the OSPF network to the EIGRP network must be available in case of a link failure.1. a small IT company. You may not remove or change any of the configuration commands currently on any of the routers.100. Two links have been added that will provide redundancy. No static or default routing is allowed in either network. You may add new commands or change default values.com. The network requirements state that you must be able to ping and telnet from loopback 101 on R1 to the OPSF domain test address of 172. They have recently merged two organizations and now need to merge their networks as shown in the topology exhibit. You have been tasked with completing the implementation and ensuring that the network requirements are met.

.

Delay.1 network (the network behind R4) in the routing table of R1 and make a ping from R1 to this network. notice that we have to divide the Delay by 10 because the metric unit is in tens of microsecond. DeIay=1000 us. Load=1. Load. Reliability=255. Reliability. Answer: Explanation/Reference: First we need to find out 5 parameters (Bandwidth. Answer: First we need to find out 5 parameters (Bandwidth. R2(config-router)# distance eigrp 90 105 This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP external routes to 105. Load.A.100. Delay. MTU) of the s0/0/0 interface (the interface of R2 connected to R4) for redistribution: R2#show interface s0/0/0 . lVITU=1500 bytes then we would redistribute as follows: R2#config terminal R2(config)# router ospf 1 R2(config-router)# redistribute eigrp 100 metric-type 1 subnets R2(config-router)#exit R2(config-router)#router eigrp 100 R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500 Note: In fact. Reliability=255. Note: The actual OPSF and EIGRP process numbers may change in the actual exam so be sure to use the actual correct values. which is better than R1 -> R2 -> R4. MTU) of the s0/0/0 interface (the interface of R2 connected to R4) for redistribution: R2#show interface s0/0/0 Write down these 5 parameters. we get Bandwidth=1544 Kbit. these parameters are just used for reference and we can use other parameters with no problem. which is smaller than the Administrative Distance of OSPF (110) -> the link between R2 & R3 will be preferred to the serial link between R2 & R4. De|ay=20000 us. MTU=1500 bytes R3#config terminal R3(config)#router ospf 1 R3(config-router)#redistribute eigrp 100 metric-type 1 subnets R3(config)#exit R3(config-router)#router eigrp 100 R3(config-router)#redistribute ospf 1 metric 10000 100 255 1 1500 Finally you should try to "show ip route" to see the 172. If the delay is 20000us then we need to divide it by 10. we must put the command below under EIGRP process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4). but the overall solution is the same. Note: If the link between R2 and R3 is FastEthernet link. Reliability.16. Load=1. For example. that is 20000/ 10 = 2000) For R3 we use the show interface fa0/0 to get 5 parameters too R3#show interface fa0/0 For example we get Bandwidth=10000 Kbit.

1 network (the network behind R4) in the routing table of R1 and make a ping from R1 to this network. which is smaller than the Administrative Distance of OSPF (110) -> the link between R2 & R3 will be preferred to the serial link between R2 & R4. which is better than R1 -> R2 -> R4.16. Reliability=255. lVITU=1500 bytes then we would redistribute as follows: R2#config terminal R2(config)# router ospf 1 R2(config-router)# redistribute eigrp 100 metric-type 1 subnets R2(config-router)#exit R2(config-router)#router eigrp 100 R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500 Note: In fact. we get Bandwidth=1544 Kbit. If the delay is 20000us then we need to divide it by 10. Note: If the link between R2 and R3 is FastEthernet link. For example. these parameters are just used for reference and we can use other parameters with no problem. that is 20000/ 10 = 2000) For R3 we use the show interface fa0/0 to get 5 parameters too R3#show interface fa0/0 For example we get Bandwidth=10000 Kbit. we must put the command below under EIGRP process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4). Note: The actual OPSF and EIGRP process numbers may change in the actual exam so be sure to use the actual correct values. MTU=1500 bytes R3#config terminal R3(config)#router ospf 1 R3(config-router)#redistribute eigrp 100 metric-type 1 subnets R3(config)#exit R3(config-router)#router eigrp 100 R3(config-router)#redistribute ospf 1 metric 10000 100 255 1 1500 Finally you should try to "show ip route" to see the 172. De|ay=20000 us. QUESTION 22 You have been asked to evaluate how EIGRP is functioning in a customer network. notice that we have to divide the Delay by 10 because the metric unit is in tens of microsecond. Load=1.Write down these 5 parameters. R2(config-router)# distance eigrp 90 105 This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP external routes to 105. DeIay=1000 us. but the overall solution is the same. . Load=1. Reliability=255.100.

Which key chain is being used for authentication of EIGRP adjacency between R4 and R2'? .

CISCO B.A. The customer has disabled your access to the show running-config command. MD5 Answer: A Explanation/Reference: QUESTION 23 Scenario: You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. . EIGRP C. key D.

How many times was SPF algorithm executed on R4 for Area 1? .

5 C. B. 9 D. 20 E. 54 F. 224 Answer: C Explanation/Reference: QUESTION 24 What is the purpose of the autonomous-system {autonomous-system-number} command? A.A. It sets the BGP autonomous system number in a VRF. The customer has disabled your access to the show running-config command. . C. It sets the global EIGRP autonomous system number. It sets the global BGP autonomous system number. 1 B. It sets the EIGRP autonomous system number in a VRF. D. Answer: A Explanation/Reference: QUESTION 25 Scenario: You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation.

How old is the Type 4 LSA from Router 3 for area 1 on the router R5 based on the output you have .

1601 C. 20 C. 1569 Answer: A Explanation/Reference: QUESTION 26 What is the default OSPF hello interval on a Frame Relay point-to-point network? A. 1858 B. 40 Answer: A Explanation/Reference: QUESTION 27 Refer to the exhibit. 600 D. 30 D. 10 B.examined? A. .

16. but users on the 192.0/8 network will not be in the routing table on Router B. The 10. E.0.0/8 network can successfully ping users on the 192. .0.0.168.0/8 network.0. D.0/8 network is missing from Router B.0. Traffic from the 172.Which one statement is true? A.0. Users on the 10. The 10. Router B will not advertise the 10. C.0.0/8 network will not be advertised by Router B because the network statement for the 10.5. B. Answer: E Explanation/Reference: QUESTION 28 You have been asked to evaluate how EIGRP is functioning in a customer network.0/24 network.168.5.0.0/24 cannot successfully ping users on the 10.0.0/8 network because it is blocked by the ACL.0.0.0.0/16 network will be blocked by the ACL.0.

What type of route filtering is occurring on R6 .

0.0/23 Answer: B Explanation/Reference: QUESTION 30 For security purposes. What caused this issue? A.8. Distribute-list using an ACL B. an IPv6 traffic filter was configured under various interfaces on the local router. 10. D. Answer: C Explanation/Reference: . Distribute-list using a route-map D.0. Distribute-list using a prefix-list C. The traffic filter is blocking all ICMPv6 traffic.8.0/16 ge 24 Ie 24? A. However.8. B.0. The link-local addresses that were used by OSPFv3 were explicitly denied.1. The global anycast address must be added to the traffic filter to allow OSPFv3 to work properly.0.8. C. 10. OSPFv3 neighbor adjacencies were lost.0/16 D.0/24 B.0/24 C. IPv6 traffic filtering can be implemented only on SV|s. An ACL using a distance of 255 Answer: A Explanation/Reference: QUESTION 29 Which prefix is matched by the command ip prefix-list name permit 10.9. 10. shortly after implementing the traffic filter.A. which caused the neighbor relationships to fail. 10.

3. distribute list 1 out B.0/24 network out of FastEthernet 0/O? A. distribute list 1 out FastEthernet0/0 C.QUESTION 31 Refer to the exhibit.2. . distribute list 2 out D. Which command only announces the 1. distribute list 2 out FastEthernet0/0 Answer: D Explanation/Reference: QUESTION 32 You have been asked to evaluate how EIGRP is functioning in a customer network.

What is the ratio of traffic over each path? .Traffic from R1 to R61 s Loopback address is load shared between R1-R2-R4-R6 and R1-R3-R5-R6 paths.

1:1 B.A. 19:80 Answer: D Explanation/Reference: QUESTION 33 You have been asked to evaluate how EIGRP is functioning in a customer network. 6:8 D. . 1:5 C.

What percent of R1's interfaces bandwidth is EIGRP allowed to use'?

A. 10
B. 20
C. 30
D. 40

Answer: B
Explanation/Reference:

QUESTION 34

You have been asked to evaluate how EIGRP is functioning in a customer network.

What is the advertised distance for the 192.168.46.0 network on R1?

A. 333056
B. 1938688
C. 1810944
D. 307456

Answer: C
Explanation/Reference:

The customer has disabled your access to the show running-config command.QUESTION 35 Scenario: You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. .

inspect their routing tables and determine which statement .Areas of Router 5 and 6 are not normal areas.

420F.0007 subnet 2001 :DB8:0:1 ::/64 Which IPv6 addresses should the engineer add to the documentation? A. 2001:DB8:0:1:C601:42FF:FEOF:7 B. 2001 :DB8:0:1 :FE80:C601 :420F:7 D. . The router has the following interface parameters: mac address C601. 2001 :DB8:0:1 :C601 :42FE:800F:7 Answer: A Explanation/Reference: QUESTION 37 Scenario: You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. Only R5's loopback is present in R5's Routing table D. Only R5's loopback is present in R6's Routing table Answer: A Explanation/Reference: QUESTION 36 An engineer has configured a router to use EUI-64. 2001:DB8:0:1:FFFF:C601:420F:7 C. The customer has disabled your access to the show running-config command.is true? A. Only R6's loopback is present in R5's Routing table E. R5's Loopback and R6's Loopback are both present in R5's Routing table B. and was asked to document the IPv6 address of the router. R5's Loopback and R6's Loopback are both present in R6's Routing table C.

Which of the following statements is true about the serial links that terminate in R3 .

IT policy requires that all outbound HTTP traffic use the frame relay link when it is available.A. Answer: B Explanation/Reference: QUESTION 38 A packet capture log indicates that several router solicitation messages were sent from a local host on the IPv6 segment.40. The R2-R3 link OSPF timer values are 30. 120 C. The R1-R3 link OSPF timer values should be 10. D. Router acknowledgment messages will be forwarded upstream. All other traffic may use either link. where the DHCP server will allocate addresses to the local host. Routers on the IPv6 segment will respond with an advertisement that provides an external path from the local subnet.com. 120. The R1-R3 link needs the neighbor command for the adjacency to stay up B. such as prefix discovery. All local host traffic will be redirected to the router with the lowest ICNIPv6 signature. a small IT company. Choose and configure the appropriate path selection feature to accomplish this task.com has two connections to the Internet. as well as certain data.40 D. ROUTE. C. . No static or default routing is allowed. one via a frame relay link and one via an EoMPLS link. Duplicate Address Detection will determine if any other local host is using the same IPv6 address for communication with the IPv6 routers on the segment. R3 is responsible for flooding LSUs to all the routers on the network. You may use the Test Workstation to generate HTTP traffic to validate your solution. B. Answer: B Explanation/Reference: QUESTION 39 You are a network engineer with ROUTE. What is the expected acknowledgment and its usage? A. which is statically defined by the network administrator.

.

.

Here are the step by Step Solution for this: 1) First create the access list that catches the HTTP traffic: R1 (config)#access-list 101 permit tcp any any eq www 2) Configure the route map that sets the next hop address to be ISP1 and permits the rest of the traffic: R1 (config)#route-map pbr permit 10 R1(config-route-map)#match ip address 101 R1 (config-route-map)#set ip next-hop 10.1.A.1.100.2 R1 (config-route-map)#exit R1 (config)#route-map pbr permit 20 3) Apply the route-map on the interface to the server in the EIGRP Network: R1 (config-route-map)#exit R1 (config)#int fa0/1 R1 (config-if)#ip policy route-map pbr R1 (config-if)#exit R1 (config)#exit Answer: Explanation/Reference: We need to configure policy based routing to send specific traffic along a path that is different from the best path in the routing table.2 R1 (config-route-map)#exit R1 (config)#route-map pbr permit 20 3) Apply the route-map on the interface to the server in the EIGRP Network: R1 (config-route-map)#exit R1 (config)#int fa0/1 R1 (config-if)#ip policy route-map pbr R1 (config-if)#exit R1 (config)#exit QUESTION 40 After you review the output of the command show ipv6 interface brief. Based on this . you see that several IPv6 addresses have the 16-bit hexadecimal value of "FFFE" inserted into the address. Answer: We need to configure policy based routing to send specific traffic along a path that is different from the best path in the routing table. Here are the step by Step Solution for this: 1) First create the access list that catches the HTTP traffic: R1 (config)#access-list 101 permit tcp any any eq www 2) Configure the route map that sets the next hop address to be ISP1 and permits the rest of the traffic: R1 (config)#route-map pbr permit 10 R1(config-route-map)#match ip address 101 R1 (config-route-map)#set ip next-hop 10.100.

DHCPv6 request B. The IPv6 universal/local flag (bit 7) was flipped.information. Answer: A Explanation/Reference: QUESTION 41 A router with an interface that is configured with ipv6 address autoconfig also has a link-local address assigned. redirect Answer: B Explanation/Reference: QUESTION 42 A company has just opened two remote branch offices that need to be connected to the corporate network. Which interface configuration output can be applied to the corporate router to allow communication to the remote sites? . C. but IPv6 Cisco Express Fon/varding was disabled. The addresses were misconfigured and will not function as intended. neighbor-solicitation D. IEEE EUI-64 was implemented when assigning IPv6 addresses on the device. what do you conclude about these IPv6 addresses? A. B. E. Which message is required to obtain a global unicast address when a router is present? A. IPv6 addresses containing "FFFE" indicate that the address is reserved for multicast. D. IPv6 unicast fon/varding was enabled. router-advertisement C.

168.165.201.200.255. DMVPN C.200.224 tunnel source Seria|0/0 tunnel mode gre multipoint B.2 tunnel destination 209.1 tunnel-mode dynamic D.231 255.201.255. FIexVPN B.161.A.231 255.165.230 255. and Cisco Express Fonrvarding? A. interface fa0/0 bandwidth 1536 ip address 209.200.165.255. dynamic routing protocol.255. Cisco Easy VPN Answer: B .224 tunnel mode gre multipoint C.224 tunnel source 192.165.1 tunnel-mode dynamic Answer: A Explanation/Reference: QUESTION 43 Which Cisco IOS VPN technology leverages IPsec. NHRP.224 tunnel source 209.200. GETVPN D.165.255.165.255.255.255. mGRE. interface Tunne|0 bandwidth 1536 ip address 209. interface Tunne|0 bandwidth 1536 ip address 209. interface fa 0/0 bandwidth 1536 ip address 209.230 255.

inbound crypto map . IPsec VPN client access C. After doing this. Which three pieces of information are displayed in the output? (Choose three. The network engineer advises the user to open a web browser. and follow the instructions. SSL VPN client access Answer: D Explanation/Reference: QUESTION 45 Which common issue causes intermittent DMVPN tunnel flaps? A. Which type of remote access did the engineer enable? A. the user is able to access company shares.) A. a routing neighbor reachability issue B. interface bandwidth congestion D. that the GRE tunnel to hub router is not encrypted Answer: A Explanation/Reference: QUESTION 46 A network engineer executes the show crypto ipsec sa command. VPDN client access D. EZVPN B. input a prescribed IP address.Explanation/Reference: QUESTION 44 A user is having issues accessing file shares on a network. a suboptimal routing table C.

2 What does the authoritative flag mean in regards to the NHRP information? A. invalid identity packets Answer: ABC Explanation/Reference: QUESTION 47 Refer to the following output: Router#show ip nhrp detail 10. Data packets are process switches for this mapping entry.B. C. D.1.1. Tunne|1 created 00:00:12. Frame Relay . NHRP mapping is for networks that are local to this router. E. expire 01:59:47 Type.12. dynamic.1Q B. B.1.2. ISL C. The mapping entry was created in response to an NHRP registration request. It was obtained directly from the next-hop sewer. PPP D. The NHRP mapping entry cannot be ovenrvritten. Answer: A Explanation/Reference: QUESTION 48 Which encapsulation supports an interface that is configured for an EVN trunk? A. Flags: authoritative unique nat registered used NBMA address: 10.2. 802.2/8 via 10. tagged packets E. remaining key lifetime C.1. untagged packets F. path MTU D.

MPLS F. HDLC Answer: A Explanation/Reference: QUESTION 49 Which three characteristics are shared by subinterfaces and associated EVNs? (Choose three. routing table C. IP address B. A packet that matches access-list with the "|og" keyword is fast switched. Answer: C Explanation/Reference: . A packet that matches access-list with the "|og" keyword is Cisco Express Forwarding switched. forwarding table D. the network engineer notices that the router CPU utilization has risen to 99 percent. D.) A. B. access-list 100 permit ip any any log After applying the access list on a Cisco router.E. NetFIow configuration Answer: ABC Explanation/Reference: QUESTION 50 Refer to the following access list. What is the reason for this? A. C. access control lists E. A large amount of IP traffic is being permitted on the router. A packet that matches access-list with the "Iog" keyword is process switched.

router(config-if)#ip helper-address 172.20. broadcast mode. You can use the RITE traffic exporter. and 49 to 172.20. 53.225 D.20. strict mode. You can use an IOS parser.225 69 53 49 Answer: A Explanation/Reference: QUESTION 53 What are the three modes of Unicast Reverse Path Forwarding? A. and broadcast mode C. and VRF mode B. which method can you use in combination with the "debug ip packet" command to limit the amount of output data? A.14. C. strict mode. B. and VRF mode . router(config-if)#udp helper-address 172. strict mode.225 C. You can disable the IP route cache globally. You can use the KRON scheduler.225 B. loose mode.14.20. loose mode.14. D. E. router(config-if)#ip udp helper-address 172. You can use an extended access list.225.14.14. Which command should be applied to the configuration to allow this? A. Answer: C Explanation/Reference: QUESTION 52 A network engineer is configuring a routed interface to forward broadcasts of UDP 69. router(config-if)#ip helper-address 172.QUESTION 51 For troubleshooting purposes.20.

destination address C. C. The router will listen on port 4433 for HTTPS traffic. The router will never accept any HTTP and HTTPS traffic. The router will listen on port 4433 for HTTP traffic.D. source address B. broadcast mode. D. Answer: A Explanation/Reference: QUESTION 56 . loose mode. The router will listen to HTTP and HTTP traffic on port 4433. router interface D. and VRF mode Answer: A Explanation/Reference: QUESTION 54 Which address is used by the Unicast Reverse Path Forwarding protocol to validate a packet against the routing table? A. B. default gateway Answer: A Explanation/Reference: QUESTION 55 Refer to the following command: router(config)# ip http secure-port 4433 Which statement is true? A.

255.0 0. It filters incoming traffic from private addresses in order to prevent spoofing and logs any intrusion attempts.0 0.255 any log router (config)#access-list 101 deny ip 172.255. 192.0.15.16.255.0. accomplish? router(config)#access-list 101 deny ip 10. C.255 any log router (config)#access-list 101 permit ip any any router (config)#interface fastEthernet 1/0 router (config-if)#ip access-group 101 in A. It prevents the internal network from being used in spoofed denial of service attacks and logs any exit to the Internet.0. D.0.0-10. only ssh traffic to vty 0 4 from source all C.255.255 any log router (config)#access-list 101 deny ip 192.255. only ssh traffic to vty 0 4 from source 2001 :DB8:0:4::32 D. which is applied on the external interface FastEthernet 1/0 of the perimeter router.255.0.0-192.168.0. 172.0. It prevents incoming traffic from IP address ranges 10.0 0. B. all traffic to vty 0 4 from source 2001 :DB8:0:4::32 B. It prevents private internal addresses to be accessed directly from outside.255.31. Answer: C Explanation/Reference: QUESTION 57 Which traffic does the following configuration allow? ipv6 access-list cisco permit ipv6 host 2001 :DB8:0:4::32 any eq ssh line vty 0 4 ipv6 access-class cisco in A.168.What does the following access list.0.0-172. all traffic to vty 0 4 from source all Answer: C Explanation/Reference: .0.0.255.255 and logs any intrusion attempts.16.168.0.

QUESTION 58 When using SNlV|Pv3 with NoAuthNoPriv. Adjust the HSRP priority without the use of preemption. NATv6 . and IPv6 to IPv6 translations at the Internet edge are performed. Enable HSRPv2 under global configuration. D. What is the best solution to ensure compliance with this new policy? A. community-string D. as an alternative to powering down the active router and letting the network respond accordingly. Track the up/down state of a loopback interface and shut down this interface during maintenance. encryption-key Answer: A Explanation/Reference: QUESTION 59 A network engineer is configuring a solution to allow failover of HSRP nodes during maintenance windows. 1-to-1. B. username B. Disable and enable all active interfaces on the active HSRP node. which allows for maintenance mode. C. which string is matched for authentication? A. Answer: A Explanation/Reference: QUESTION 60 A company's corporate policy has been updated to require that stateless. NAT44 C. password C. Which action will allow for manual switching of HSRP nodes? A. NAT64 B.

B. It rewrites transport layer headers. What can you determine based on this information? A. Cisco Express Forwarding has not been configured globally. NPTv6 Answer: E Explanation/Reference: QUESTION 61 What is a function of NPTv6? A. NPTv4 E. It interferes with encryption of the full IP payload. C. After reviewing the output of NetF|ow. C. Answer: C Explanation/Reference: QUESTION 62 An organization decides to implement NetF|ow on its network to monitor the fluctuation of traffic that is disrupting core services. Flow Export version 9 is in use. the network engineer is unable to see OUT traffic on the interfaces. It maintains a per-node state.D. D. It is checksum-neutral. D. NetFIow output has been filtered by default. Answer: A Explanation/Reference: QUESTION 63 . B. The command ip flow-capture fragment-offset has been enabled.

Assuming that an NTP server is already set up. connectionless-oriented B. Which type of statistics does the engineer see? A. Answer: A Explanation/Reference: QUESTION 65 Refer to the exhibit. It enables a device to be an NTP peer to another device.A network engineer initiates the ip sla responder tcp-connect command in order to gather statistics for performance gauging. connection-oriented D. B. service-oriented C. It enables receiving NTP broadcasts on all interfaces globally. D. application-oriented Answer: C Explanation/Reference: QUESTION 64 A network engineer is trying to implement broadcast-based NTP in a network and executes the ntp broadcast client command. It enables receiving NTP broadcasts on the interface where the command was executed. Which statement about the output of the show flow-sampler command is true? . C. It enables a device to receive NTP broadcast and unicast packets. what is the result of the command? A.

D. Which functions do the two commands serve in this scenario? A. D. The sampler matched 10 packets. The sampler matched 10 packets. Answer: A Explanation/Reference: QUESTION 66 A network engineer is asked to configure a "site-to-site" IPsec VPN tunnel. NAT B. dual-stack NAT E. C. one packet every 100 packets. Which feature allows IPv6 devices to communicate with IPv4 servers? A. NAT64 D. The command ip nat inside source list 1 int s0/0 overload disables "many-to-one" access for all devices on a defined segment to share a single IP address upon exiting the external interface. B. each packet randomly chosen from every group of 100 packets. B. The command access-Iist1 permit any defines only one machine that is allowed through the tunnel. One of the last things that the engineer does is to configure an access list (access-list 1 permit any) along with the command ip nat inside source list 1 int s0/0 overload. C. Answer: D Explanation/Reference: QUESTION 67 IPv6 has just been deployed to all of the hosts within a network. one packet every 100 seconds. The sampler matched 10 packets. NATng C. The command ip nat inside source list 1 int s0/0 overload provides "many-to-one" access for all devices on a defined segment to share a single IP address upon exiting the external interface.A. The sampler matched 10 packets. DNS64 . each one randomly chosen from every 100-second interval. The command access-list 1 defines interesting traffic that is allowed through the tunnel. but not to the servers.

manual D. discover messages B. static F. automatic E. stateless B. traffic from a trusted DHCP server to client D. functional G. DHCP messages where the destination MAC and client MAC do not match Answer: B Explanation/Reference: QUESTION 69 Which two methods of deployment can you use when implementing NAT64? (Choose two.Answer: C Explanation/Reference: QUESTION 68 Which type of traffic does DHCP snooping drop? A. DHCP messages where the source MAC and client MAC do not match C. dynamic Answer: AB Explanation/Reference: QUESTION 70 . stateful C.) A.

However.) A.28 traps version 2c CISCORO B.201. Which feature should the engineer use to gather the required information? A.28 informs version 3 auth CISCORO Answer: A Explanation/Reference: QUESTION 71 A network engineer is notified that several employees are experiencing network performance related issues. WCCP Answer: C Explanation/Reference: QUESTION 72 After a recent DoS attack on a network. router(config)#snmp-server host 172. NetFIow D.28 informs version 2c CISCORO C. . router(config)#snmp-server host 172. In order to identify which specific type of traffic is causing this slowness.201.16.16. Cisco IOS EEM C.201. SNMP B. router(config)#snmp-server host 172. the engineer is not concerned with authentication or encryption.28 traps version 3 auth CISCORO D. Which two actions can you take to provide enhanced logging results? (Choose two.16. router(config)#snmp-server host 172.201. and bandwidth-intensive applications are identified as the root cause.A network engineer is configuring SNMP on network devices to utilize one-way SNMP notifications. Syslog E. information such as the source/destination IP and Layer 4 port numbers is required. Use the msec option to enable service time stamps.16. senior management asks you to implement better logging functionality on all IOS-based devices. Which command satisfies the requirements of this scenario? A.

Increase the logging history. flow collector Answer: A Explanation/Reference: QUESTION 74 A network engineer has left a NetF|ow capture enabled over the weekend to gather information regarding excessive bandwidth utilization. D. current status of the specified flow exporter C. configuration of the specified flow exporter B. Set the logging severity level to 1. flow sampler D. flow exporter C. C.B. configuration of the specified flow monitor Answer: B Explanation/Reference: . status and statistics of the specified flow monitor D. The following command is entered: switch#show flow exporter F|ow_Exporter-1 What is the expected output? A. flow monitor B. Disable event logging on all noncritical items. E. Specify a logging rate limit. Answer: AB Explanation/Reference: QUESTION 73 Which NetFIow component is applied to an interface and collects information about flows? A.

) A. which feature can the engineer use to create a crash collection? A. In this situation. NetF|ow Answer: B Explanation/Reference: QUESTION 76 Which two functions are completely independent when implementing NAT64 over NAT-PT? (Choose two. stateless translation E. session handling Answer: AB Explanation/Reference: QUESTION 77 What is the result of the command ip flow-export destination 10.QUESTION 75 A network engineer finds that a core router has crashed without warning. core dumps C. warm reloads D. DNS B. It configures the router to export cache flow information to IP 10. . SNMP E. NAT C.1 on port UDP/5858.10.10.1 5858? A.10. port redirection D.10. secure copy protocol B.

C.10. It configures the router to receive cache flow information from IP 10. enqueuing for the RP C. D. Answer: A Explanation/Reference: QUESTION 78 A network engineer executes the "ipv6 f|owset" command. It configures the router to export cache flow information about flows with destination IP 10. What is the result? A. output drops B. adjacency issues Answer: A Explanation/Reference: . fragmentation failures D.10.1 and port UDP/5858.1 and port UDP/5858. IPv6 flow control is enabled on the router. B. Answer: A Explanation/Reference: QUESTION 79 A network engineer executes the show ip flow export command. C. IPv6 PMTU is enabled on the router. Flow-set marking in 1280-byte or larger packets is enabled. Flow-label marking in 1280-byte or larger packets is enabled.10. It configures the router to receive cache flow information about flows with destination IP 10.10.1 on port UDP/5858.B. D. Which line in the output indicates that the send queue is full and export packets are not being sent? A.10.10.

totally stubby area C. BOOTP Answer: AB Explanation/Reference: QUESTION 81 The OSPF database of a router shows LSA types 1. SLAAC C. 3. EUI-64 B. Which type of IPv6 address is portrayed in the exhibit? . 2.QUESTION 80 The following configuration is applied to a router at a branch site: ipv6 dhcp pool dhcp-pool dns-server 2001 :DB8:1 :B::1 dns-server 2001 :DB8:3:307C::42 domain-name exampIe.) A. Which type of area is this router connected to? A. not-so-stubby area Answer: D Explanation/Reference: QUESTION 82 Refer to the exhibit. and 7 only. backbone area D.com I If IPv6 is configured with default settings on all interfaces on the router. DHCPv6 D. which two dynamic IPv6 addressing mechanisms could you use on end hosts to provide end-to-end connectivity? (Choose two. stub area B. The command is executed while configuring a point-to-multipoint Frame Relay interface.

RADIUS Answer: BC Explanation/Reference: QUESTION 84 Refer to the exhibit. After configuring GRE between two routers running OSPF that are connected to each other via a WAN link. PAP C. multicast Answer: A Explanation/Reference: QUESTION 83 Which two authentication protocols does PPP support? (Choose two. What is the reason for this? .) A. link-local B. site-local C. CHAP D. global D. EAP E. WAP B.A. a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates.

B. Either a firewall between the two routers or an ACL on the router is blocking UDP 57. when packets on the interface are received and forwarded to a configured syslog server D. Answer: A Explanation/Reference: QUESTION 85 A network engineer is investigating the cause of a service disruption on a network segment and executes the debug condition interface fastethernet f0/0 command. when packets on the interface are received and logging buffered is enabled C. when packets on the interface are received and the interface is shut down Answer: A Explanation/Reference: . C. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 47. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 57. Either a firewall between the two routers or an ACL on the router is blocking TCP 47. D.A. when packets on the interface are received and the interface is operational B. In which situation is the debugging output generated? A.

Cannot remove message or the %PooI outpool in use.0 Upon entering the command on the IOS router.254 netmask 255. the following message is seen on the console: %Dynamic IVIapping in Use.1. B. EIGRP D. then replace the NAT configuration quickly. before any new NAT entries are populated into the translation table due to active NAT traffic. then replace the NAT configuration quickly.255. Clear the IP NAT translations using the clear ip nat traffic * " command.1.1. C.QUESTION 86 Which protocol is used in a DIVIVPN network to map physical IP addresses to logical IP addresses? A. before any new NAT entries are populated into the translation table due to active NAT traffic. Answer: B . LLDP C. NHRP Answer: D Explanation/Reference: QUESTION 87 A network engineer is trying to modify an existing active NAT configuration on an IOS router by using the following command: (config)# no ip nat pool dynamic-nat-pool 192. BGP B. then replace the NAT configuration quickly. cannot destroy What is the least impactful method that the engineer can use to modify the existing IP NAT configuration? A.20 192. then replace the NAT configuration quickly.1. before any new NAT entries are populated into the translation table due to active NAT traffic. Clear the IP NAT translations using the clear ip nat table * " command. D. before any new NAT entries are populated into the translation table due to active NAT traffic. Clear the IP NAT translations using the reload command on the router. Clear the IP NAT translations using the clear ip nat translation * " command.255.

1? A. multicast Answer: C Explanation/Reference: QUESTION 89 Which outbound access list. ip access-list extended 10 deny tcp host 10.1 any eq 80 permit ip any any .10.10. permits all traffic except for http traffic sourced from the workstation with IP address 10.10. applied to the WAN interface of a router. VRRP C. IP SLA D. Which technology can be employed to automatically detect a WAN primary link failure and failover to the secondary link? A.Explanation/Reference: QUESTION 88 Refer to the exhibit.1 eq 80 any permit ip any any B.10. HSRP B.10. ip access-list extended 200 deny tcp host 10.10.

10. Dual stack translates IPv6 addresses to IPv4 addresses. Which option is the problem? A. network switching loop C. the engineer finds traffic flood in the network. Upon monitoring.10. network outage B. wrong proxy configured Answer: B Explanation/Reference: . router configuration issue D. Answer: B Explanation/Reference: QUESTION 91 Various employees in the same department report to the network engineer about slowness in the network connectivity to the Internet. Dual stack changes the IP addresses on hosts from IPv4 to IPv6 automatically. B. ip access-list extended 100 deny tcp host 10. D. Dual stack means that devices are able to run IPv4 and IPv6 in parallel. C.10. ip access-list extended NO_HTTP deny tcp host 10.1 any eq 80 permit ip any any Answer: D Explanation/Reference: QUESTION 90 Which statement about dual stack is true? A. They are also having latency issues communicating to the network drives of various departments.C. Dual stack translates IPv4 addresses to IPv6 addresses.1 any eq 80 D.10.

252 I ip route 172.16.255.1. .1.1.255.255.1.31.1.1.1.255.QUESTION 92 Refer to the exhibit.255.010.0 interface serial 0/0 ip address 10.2 B. RouterB(config-if)# ip helper-address 172.255.16.1 C.255.0 255.255.1 D.31. Consider the following output: hostname RouterB I interface fastethernet 0/0 ip address 172.16.1 255.255 Answer: A Explanation/Reference: QUESTION 93 Refer to the exhibit. RouterB(config-if)# ip helper-address 172. The DHCP client is unable to receive a DHCP address from the DHCP server. RouterB(config-if)# ip helper-address 172.1.2 Which configuration is required on the Router B fastethernet 0/0 port in order to allow the DHCP client to successfully receive an IP address from the DHCP serwer? A.1 255.1. RouterB(config-if)# ip helper-address 255.

Core(config-router)# passive-interface Gi0/0 Core(config-router)# passive-interface Gi3/1 Core(config-router)# passive-interface Gi3/2 DHCP(config-router)# no passive-interface Gil/0 .Which option prevents routing updates from being sent to the DHCP router. while still allowing routing update messages to flow to the Internet router and the distribution switches? A. DHCP(config-router)# passive-interface default DHCP(config-router)# no passive-interface Gil/0 Internet(config-router)# passive-interface Gi0/1 Internet (config-router)# passive-interface Gi0/2 B.

priv D. Core(config-router)# passive-interface default Core(config-router)# no passive-interface Gi0/0 Core(config-router)# no passive-interface Gi3/1 Core(config-router)# no passive-interface Gi3/2 D.C.) A. NetF|ow C. secret . noauth C. built-in GUI D. auth B. CLI B. syslog server interface E. web interface Answer: AB Explanation/Reference: QUESTION 95 Which parameter in an SNMPv3 configuration offers authentication and encryption? A. Internet(config-router)# passive-interface default Core(config-router)# passive-interface default DSW1(config-router)# passive-interface default DSW2(config-router)# passive-interface default Answer: C Explanation/Reference: QUESTION 94 In which two ways can NetF|ow data be viewed? (Choose two.

a private AS number B. a public AS number C. allow default route C. allow self ping to router B. router#show memory allocating-process table .) A. allow based on ACL match D.Answer: C Explanation/Reference: QUESTION 96 Which type of BGP AS number is 64591? A. a private 4-byte AS number D. source reachable via both Answer: D Explanation/Reference: QUESTION 98 Which two commands would be used to troubleshoot high memory usage for a process? (Choose two. a public 4-byte AS number Answer: A Explanation/Reference: QUESTION 97 Which option is invalid when configuring Unicast Reverse Path Fonrvarding? A.

site-local D.B. router#show memory processor statistics Answer: AB Explanation/Reference: QUESTION 99 Which type of handshake does CHAP authentication use to establish a PPP link? A. anycast E. global C. one-way B. link-local B. four-way Answer: C Explanation/Reference: QUESTION 100 Which IPv6 address type is seen as the next-hop address in the output of the show ipv6 rip RIPng database command? A. multicast Answer: A Explanation/Reference: . router#show memory dead D. router#show memory events E. three-way D. two-way C. router#show memory summary C.

They become authenticated and encrypted.50. They become unauthenticated and unencrypted. a network engineer is using the AuthNoPriv security level. It allows external clients to connect to a web server hosted on 192.1 8080 extendable A. D.168.1.201. They become authenticated and unencrypted. They become unauthenticated and encrypted.50 to access external websites using TCP port 8080.165. Answer: B Explanation/Reference: QUESTION 103 Refer to the exhibit.168.168. B.QUESTION 101 Which statement describes what this command accomplishes when inside and outside interfaces are correctly identified for NAT? ip nat inside source static tcp 192.50. It represents an incorrect NAT configuration because it uses standard TCP ports. .50 80 209.165.1.1. C.1 to connect to a web server at 192. It allows external clients coming from public IP 209. B. It allows host 192. C.201.168. Answer: C Explanation/Reference: QUESTION 102 To configure SNlV|Pv3 implementation. What effect does this action have on the SNMP messages? A.1. D.

D.Which statement about the configuration is true? A. This configuration represents a complete PPPoE client configuration on an Ethernet connection. Answer: A Explanation/Reference: QUESTION 105 . This configuration is missing an IP address on the dialer interface. B. Answer: D Explanation/Reference: QUESTION 104 An engineer executes the ip flow ingress command in interface configuration mode. This configuration is incorrect because the dialer interface number must be the same as the dialer pool number. It enables IP flow collection on the physical interface and its subinterfaces. C. D. C. This configuration is incorrect because the MTU must match the ppp-max-payload that is defined. What is the result of this action? A. It enables IP flow while disabling IP CEF on the interface. It enables the collection of IP flow samples arriving to the interface. It enables the collection of IP flow samples leaving the interface. B.

Answer: D Explanation/Reference: QUESTION 106 Which two statements about AAA implementation in a Cisco router are true? (Choose two. C.) A. RADIUS and TACACS+ allow accounting of commands. B. By default. Which consideration should be analyzed? A. By default. RADIUS is more filexible than TACACS+ in router management. typically is fragmented C. EIGRP performs equal cost load balancing at least across four equal cost paths. RADIUS and TACACS+ are client/server AAA protocols. Answer: BD Explanation/Reference: QUESTION 107 Which traffic characteristic is the reason that UDP traffic that carries voice and video is assigned to the queue only on a link that is at least 768 kbps? A. RADIUS and TACACS+ encrypt the entire body of the packet. EIGRP uses a default variance of 2 for load balancing. EIGRP allows a maximum of four paths across for load balancing traffic. C. causes excessive delays for video traffic Answer: A . EIGRP unequal path load balancing can result in routing loops.A network engineer is considering enabling load balancing with EIGRP. D. B. causes windowing D. D. typically is not fragmented B. E. Neither RADIUS nor TACACS+ allow for accounting of commands.

Explanation/Reference: QUESTION 108 Drag and drop the BGP states from the left to the matching definitions on the right. .

Cisco Easy VPN C.A. GETVPN D. Answer: Answer: Explanation/Reference: QUESTION 109 Which Cisco VPN technology uses AAA to implement group policies and authorization and is also used for the XAUTH authentication method? A. DIVIVPN B. GREVPN Answer: B .

Which two configurations enable the local or remote router to ping the loopback from any existing interface? (Choose two. router(config-ip-s|a)#udp-echo 172. router(config-ip-sla-echo)#timeout 3 C. adding a static route for the VRF that points to the global route table B. a new loopback is added to Router 1.25 source-interface FastEthernet 0/0 B. adding the loopback to the VRF C. router(config-ip-sla)#icmp-echo 172.201. At a later time.25 source-port 23 F. router(config-ip-sla-echo)#frequency 3 E. adding a static route for the VRF that points to the loopback interface F.25 interval 100 D. adding the IP address of the loopback to the export route targets for the VRF E.Explanation/Reference: QUESTION 110 A network engineer has set up VRF-Lite on two routers where all the interfaces are in the same VRF.201.16. but it cannot ping any of the existing interfaces. adding all interfaces to the global and VRF routing tables Answer: AB Explanation/Reference: QUESTION 111 An engineer is asked to monitor the availability of the next-hop IP address of 172.201.) A. router(config-ip-sIa)#icmp-jitter 172. router(config-ip-s|a-echo)#thresho|d 3 Answer: AD Explanation/Reference: .16. Which two commands accomplish this task? (Choose two.16. adding dynamic routing between the two routers and advertising the loopback D.) A.16.25 every 3 seconds using an ICIVIP echo packet via an ICIVIP echo probe.201.

QUESTION 112 Refer to the exhibit. D. and usability D. reduced configuration and deployment time for dot1q trunking E. Which statement about the configuration is true? A. simplified Layer 3 network virtualization B. 20 packets are being sent every 30 seconds. B. troubleshooting. Answer: A Explanation/Reference: QUESTION 113 Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three. C. Jitter is being tested with TCP packets to port 65051.) A. The monitor starts at 12:05:00 a. increased network performance and throughput F. decreased BGP neighbor configurations . improved shared services support C. enhanced management. The packets that are being sent use DSCP EF.m.

ip nat outside source static 209.10.165. Which command allows hosts that are connected to FastEthernet0/2 to access the Internet? A.10.Answer: ABC Explanation/Reference: QUESTION 114 Refer to the exhibit. Which technology must be configured to prevent remote sites from getting overwhelmed with traffic and prevent packet drops from the headquarters? . ip nat inside source list 10 interface FastEthernet0/2 overload D.200. ip nat outside source list 10 interface FastEthernet0/2 overload Answer: A Explanation/Reference: QUESTION 115 A company has their headquarters located in a large city with a T3 frame relay link that connects 30 remote locations that each have T1 frame relay connections. ip nat inside source list 10 interface FastEthernet0/1 overload B.0 overload C.225 10.

D. RADIUS uses TCP.A. GRE VPN D. IPsec VPN C. TACACS+ encrypts only the password portion of a packet. C. and TACACS+ uses UDP. traffic shaping B. Which statement is true? . MPLS Answer: A Explanation/Reference: QUESTION 116 Which statement is true? A. Answer: D Explanation/Reference: QUESTION 117 Refer to the exhibit. TACACS+ separates authentication and authorization. RADIUS encrypts the entire body of the packet. B.

0/8 network.0.0.0. what is the bandwidth delay product? A.0/8 network because it is blocked by the ACL. The 10.168.0.0.0.0.000 bytes C. Router B will not advertise the 10. C.0/8 network can successfully ping users on the 192.168.000 bytes .0/8 network will not be in the routing table on Router B.0.16. The 10.0. B. Traffic from the 172.0/24 network. E. D.0.000 bytes D. 8.5.0. Users on the 10.0/8 network will not be advertised by Router B because the network statement for the 10. 24.0.5. 16.0/8 network is missing from Router B. 32.0/16 network will be blocked by the ACL.000 bytes B. Answer: E Explanation/Reference: QUESTION 118 If the total bandwidth is 64 kbps and the RTT is 3 seconds. but users on the 192.0/24 cannot successfully ping users on the 10.A.0.

by looking in the routing table for an alternate FIB entry Answer: B Explanation/Reference: QUESTION 120 What are the default timers for RIPng? A. by creating a new FIB entry for the packet D.E. by fonrvarding the packet B. 62. Update: 20 seconds Expire: 120 seconds Flush: 160 seconds C. Update: 10 seconds Expire: 60 seconds Flush: 80 seconds D. by dropping the packet C.000 bytes Answer: C Explanation/Reference: QUESTION 119 How does an IOS router process a packet that should be switched by Cisco Express Fonrvarding without an FIB entry? A. if the required matching is based on which criteria? . Update: 30 seconds Expire: 180 seconds Flush: 240 seconds B. Update: 5 seconds Expire: 30 seconds Flush: 40 seconds Answer: A Explanation/Reference: QUESTION 121 A route map uses an ACL.

AS paths D. In order to update the next hop for the interesting traffic. IGP Answer: B Explanation/Reference: QUESTION 123 Which three items can you track when you use two time stamps with IP SLAs? (Choose three. path . addressing information B. route types C. metrics Answer: A Explanation/Reference: QUESTION 122 A network engineer has configured a tracking object to monitor the reachability of IP SLA 1. PBR C. SNMP B.A. packet loss D.) A. load E. SAA E. ACLs F. jitter C. throughput F. delay B. IP SLA D. which feature must be used in conjunction with the newly created tracking object to manipulate the traffic flow as required? A.

Answer: B Explanation/Reference: QUESTION 125 An engineer is configuring a GRE tunnel interface in the default mode. router (config-Iine)# ntp master 10 Which statement about this command is true? A. Which option also is required on the tunnel interface before it is operational? A. D. The router acts as an authoritative NTP clock for 10 minutes only. tunnel protection Answer: A Explanation/Reference: QUESTION 126 . The router acts as an authoritative NTP clock with a priority number of 10. The engineer has assigned an IPv4 address on the tunnel and sourced the tunnel from an Ethernet interface. C. The router acts as an authoritative NTP clock at stratum 10. keepalives C. IPv6 address D. The router acts as an authoritative NTP clock and allows only 10 NTP client connections. B. tunnel destination address B.Answer: ABC Explanation/Reference: QUESTION 124 Refer to the following configuration command.

10. The router exports flow information to 10.Refer to the exhibit. The router receives flow information from 10. B.10.10.1 on TCP port 5127.10. D.2 on UDP port 5127. Answer: A Explanation/Reference: QUESTION 127 Which two routing protocols are supported by Easy Virtual Network'? (Choose two. The router receives flow information from 10.10.2 on TCP port 5127.10. The router exports flow information to 10.10.1 on UDP port 5127.10.) . Which statement about the command output is true? A. C.

Answer: C Explanation/Reference: QUESTION 129 Which two statements indicate a valid association mode for NTP synchronization? (Choose two. It manages the import and export of routes between two or more VRF instances. BGP D. The client polls NTP servers for time. IS-IS Answer: BD Explanation/Reference: QUESTION 128 What is the purpose of the route-target command? A. D.) A. B. C. OSPFv2 C. The client creates a VPN tunnel to an NTP server. It extends the IP address to identify which VRF instance it belongs to.A. The client multicasts NTP requests. The client broadcasts NTP requests. The client listens to NTP broadcasts. D. EIGRP E. C. E. Answer: AC Explanation/Reference: . It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol capabilities. It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities. B. R|Pv2 B.

Which option prevents routing updates from being sent to the access layer switches? A. DWS1(config-router)# passive-interface default DWS2(config-router)# passive-interface default .QUESTION 130 Refer to the exhibit.

ALS1(config-router)# passive-interface default ALS2(config-router)# passive-interface default C.) A. serial interfaces B. DWS1(config-router)# passive-interface gi1/1 DWS1(config-router)# passive-interface gi1/2 DWS2(config-router)# passive-interface gi1/1 DWS2(config-router)# passive-interface gi1/2 D. auxiliary interfaces Answer: AD Explanation/Reference: QUESTION 132 A network administrator is troubleshooting a DMVPN setup between the hub and the spoke. ISDN interfaces E.B. Ethernet interfaces C. fiber interfaces D. Which action should the administrator take before troubleshooting the IPsec configuration? . ALS1(config-router)# passive-interface gi0/1 ALS1(config-router)# passive-interface gi0/2 ALS2(config-router)# passive-interface gi0/1 ALS2(config-router)# passive-interface gi0/2 Answer: C Explanation/Reference: QUESTION 131 On which two types of interface is Frame Relay switching supported? (Choose two.

B. resulting in a single GRE tunnel interface on the hub. Verify crypto maps. Verify NHRP. Cisco Easy VPN D. GETVPN C. MS CHAP B. Verify ISAKMP. C. DMVPN B.A. CDPCP C. to support multiple connections from multiple spoke devices? A. Answer: A Explanation/Reference: QUESTION 133 Which PPP authentication method sends authentication information in cleartext? A. F|exVPN Answer: A Explanation/Reference: . CHAP D. Verify the GRE tunnels. PAP Answer: D Explanation/Reference: QUESTION 134 Which Cisco VPN technology can use multipoint tunnel. D.

A. Answer: .QUESTION 135 Drag and drop the IPv6 NAT characteristic from the left to the matching IPv6 NAT category on the right.

. an OK or over threshold return code means that the track's state is up. Which three elements can you use to identify an IPv6 packet via its header. When tracking state. Source address C. C. When tracking state. When tracking state. Destination Address F. Fragment Offset Answer: ACD Explanation/Reference: QUESTION 137 Two aspects of an IP SLA operation can be tracked: state and reachability. an OK return code means that the track's state is up. an OK return code means that the track's state is down. an OK or over threshold return code means that the track's state is down. in order to filter future attacks? (Choose three. Flow Label D. Traffic Class B. Which statement about state tracking is true? A. When tracking state. Hop Limit E. any other return code means that the track's state is up.) A. any other return code means that the track's state is down. any other return code means that the track's state is down. D.Answer: Explanation/Reference: QUESTION 136 The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. any other return code means that the track's state is up. B.

OI 2001:DB8::/32 [110/100] via FE80::A8BB:CCFF:FE00:6F00.Answer: A Explanation/Reference: QUESTION 138 Refer to the exhibit. Ethernet0/0 D. Ethernet0/0 Answer: A Explanation/Reference: QUESTION 139 Drag and drop the Cisco Express Fon/varding adjacency types from the left to the correct type of processing on the right. which route is the summarized route? A. OI 2001:DB8::/24 [110/100] via FE80::A8BB:CCFF:FE00:6F00. OI 2001:DB8::/48 [110/100] via FE80::A8BB:CCFF:FE00:6F00. When summarizing these routes. Ethernet0/0 C. OI 2001:DB8::/64 [110/100] via FE80::A8BB:CCFF:FE00:6F00. . Ethernet0/0 B.

.

Answer: Answer: Explanation/Reference: QUESTION 140 .A.

C. B. It is used to translate IPv4 prefixes to IPv6 prefixes. C. B. lVIuItipIe PPPoE clients can use the same dialer interface. D. SLAAC provides the ability to address a host based on a network prefix that is advertised from a local network router. routing protocol D. A PPPoE session can be initiated only by the access concentrator. A PPPoE session can be initiated only by the client. How is the prefix advertised? A. lVIuItipIe PPPoE clients can use the same dialer pool. routing type Answer: B Explanation/Reference: QUESTION 142 Which statement about the NPTv6 protocol is true? A. D. routing table B. It is used to translate IPv4 addresses to IPv6 link-local addresses.Which statement is a restriction for PPPoE configuration? A. It is used to translate IPv6 prefixes to IPv4 subnets with appropriate masks. Answer: C Explanation/Reference: QUESTION 141 In IPv6. . router advertisements C. It is used to translate an IPv6 address prefix to another IPv6 prefix.

Answer: B Explanation/Reference: QUESTION 143 What is the primary service that is provided when you implement Cisco Easy Virtual Network? A. windowing D. B. It reduces the need for common services separation. TCP E. It requires and enhances the use of VRF-Lite. global synchronization Answer: A Explanation/Reference: QUESTION 145 A router receives a routing advertisement for the same prefix and subnet from four different routing protocols. It allows for traffic separation and improved network efficiency. PMTUD B. D. MSS C. It introduces multi-VRF and label-prone network segmentation. Which advertisement is installed in the routing table? . Answer: C Explanation/Reference: QUESTION 144 Which technology was originally developed for routers to handle fragmentation in the path between end points? A. C.

Which option represents the minimal configuration that allows inbound traffic from the 172. OSPF C.0/8 hosts that could enter router R? A. (config)#no ip cef (config)#interface fa0/0 (config-if)#ip verify unicast source reachable-via rx .16.0/24 network to successfully enter router R. (config)#ip cef (config)#interface fa0/0 (config-if)#ip verify unicast source reachable-via rx C.1. (config)#ip cef (config)#interface fa0/0 (config-if)#ip verify unicast source reachable-via rx allow-default B.0.A. while also limiting spoofed 10.0. EIGRP Answer: D Explanation/Reference: QUESTION 146 Refer to the exhibit. RIP B. IBGP D.

R1 will reply to R2 with the advertisement for network 192.0/27 with a hop count of 16 to R1. C. E. After communication fails and after the hold-down timer expires.0/27 with a hop count of 16. Answer: AC Explanation/Reference: QUESTION 148 What is the function of the snmp-server manager command? .2. R2 will advertise network 192.0/27 route from its routing table.168. (config)#interface fa0/0 (config-if)#ip verify unicast source reachable-via any Answer: A Explanation/Reference: QUESTION 147 Refer to the exhibit. D.2. R1 will remove the 192. R3 will not accept any further updates from R2. due to the split-horizon loop prevention mechanism.) A.D. R2 will not send any advertisements and will remove route 192.2. B.2.168.0/27 from its routing table.168. The network setup is running the RIP routing protocol.168. Which two events will occur following link failure between R2 and R3? (Choose two.

16.A.16. to enable the device to send and receive SNMP requests and responses B. The router must have a route installed towards the tunnel destination B. to disable SNMP messages from getting to the SNMP engine C. which statement about routers and the tunnel destination address is true? A.8:80 is translated to 172.8 8080 172. Any packet that is received in the inside interface with a source IP port address of 172 16 10 8 8080 is translated to 172. Any packet that is received in the inside interface with a source IP address of 172 16 10 8 is redirected to port 8080 or port 80 C.8 80 Answer: A Explanation/Reference: QUESTION 150 When the tunnel interface is configured in default mode.8 8:80 B.16. to enable the device to send SNMP traps to the SNMP server D. to configure the SNMP server to store log data Answer: A Explanation/Reference: QUESTION 149 Refer to the following configuration command.16. the router must have redirects enabled outbound towards the tunnel destination . The router accepts only a TCP connection from port 8080 and port 80 on IP address 172 16 10 8 D.10. Any packet that is received in the inside interface with a source IP port address of 172.10. router(config)# ip nat inside source static tcp 172.10.8 80 Which statement about the command is true? A. the router must have WCCP redirects enabled inbound from the tunnel destination C.10.16.10. the router must have cisco discovery protocol enabled on the tunnel to form a CDP neighbor ship with the tunnel destination D.

Answer: A Explanation/Reference: QUESTION 151 Refer to the exhibit. Create a more specific ARP entry to define how to reach the remote router. Save the configuration and reload the router. A network engineer has configured GRE between two IOS routers. C. SMTP . Create a more specific static route to define how to reach the remote router. which option must be the same on all routers for EIGRP authentication key role over to work correctly? A. D. Check whether the internet sen/ice provider link is stable Answer: A Explanation/Reference: QUESTION 152 Other than a working EIGRP configuration. The state of the tunnel interface is continuously oscillating between up and down. B. What is the solution to this problem? A.

the one with the lowest stratum is preferred B. If multiple NTP sewers are configured. broadcast D. the one with the highest stratum is preferred. SNMP C. "Stratum" refers to the number of hops between the NTP client and the NTP server. By default. Answer: AB Explanation/Reference: QUESTION 154 What type of 1Pv6 packet will indicate traffic from single host and single node? A. unicast C. NTP communications use UDP port 123. C. E. Locally configured time overrides time received from an NTP server.) A.B. multicast B. If multiple NTP sewers are configured. anycast Answer: B Explanation/Reference: QUESTION 155 . D. Passwords D. Time Answer: C Explanation/Reference: QUESTION 153 Which two statements about NTP operation are true? (Choose two.

1.168.4 F.1.1. C. Disabling split horizon Answer: CE Explanation/Reference: QUESTION 156 Refer to Exhibit: Which three NTP features can be deduced on the router? (choose three) A. Configure a loopback interface with Frame Relay to various remote sites. E. only updates its time from 192. only is in stratum 4 D.168. only handle four requests at a time C.168.1.168.In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two. Configuring multiple subinterfaces on a single physical interface to various remote sites. Enabling split horizon. D. only accepts time requests from 192.) A. only accepts time requests from 192. only updates its time from 192.4 .1 E. B.1 B. Configuring one physical serial interface with Frame Relay to various remote sites.

Cd34$ !ao0 D. Which option can cause the VOIP quality to suffer? A.Cd34$!aoO B. enable secret $abc%!#. load balancing over redundant links Answer: D Explanation/Reference: . The network engineer does a packet capture and sees out-of-order packets being delivered. traffic over backup redundant links B. enable secret 15 $abc%i#. enable secret 6 $abc%!#. enable secret 0 Sabc%U * .Answer: ACF Explanation/Reference: QUESTION 157 What command can you enter to configure an enable password that uses an encrypted password from another configuration? A.Cd34$!aoO Answer: D Explanation/Reference: QUESTION 158 A network engineer receives reports about poor voice quality issues at a remote site. enable secret 5 $abc%!#. misconfigured voice vlan C.Cd34$!aoO E. enable secret 7 Sabc%!#.Cd34$!aoO F.Cd34$!ao0 C. speed duplex link issues D.

) A. Unreliable delivery C. A network engineer is troubleshooting a DIVIVPN setup between the hub and the spoke. What is the problem? A. An incompatible ISAKIVIP policy Answer: B Explanation/Reference: QUESTION 160 Which two attributes describe UDP within a TCP/IP network? (Choose two. Connection-oriented communication E. Connectionless communication D. Increased headers Answer: BC Explanation/Reference: QUESTION 161 Which three IP SLA performance metrics can you use to monitor enterprise-class networks? (Choose . That ISAKIVIP is using default settings C.QUESTION 159 Refer to the exhibit. Acknowledgments B. That ISAKIVIP is not enabled B. The engineer executes the command show crypto isakmp sa and observes the output that is displayed. An incompatible IP sec transform set D.

Threshold action C. Which two feature are need to implements this functionality? (choose two) A. Incorrect neighbor options B. Reliability F. PAcket loss B. What is the potential problem? A. Delay C. traps Answer: ABO Explanation/Reference: QUESTION 162 A network administrator notices that the BGP state drops and logs are generated for missing BGP hello keepalives. MOS B. bandwidth D. BGP path MTU enabled D.) A. Cisco IOS EEM D. MTU mismatch Answer: D Explanation/Reference: QUESTION 163 A network engineer wants to notify a manager in the events that the IP SLA connection loss threshold reached. Hello timer mismatch C.three. SNMP traps . Connectivity E.

Router#show crypto ipsec tra nsform-set E.E. Router#show crypto ipsec sa B. Router#show crypto engine connections active Answer: A Explanation/Reference: QUESTION 166 . Router#show crypto isakmp peers C. Which command should the administrator execute to accomplish this task? A. dotle C. MBGP Answer: C Explanation/Reference: QUESTION 165 A network engineer wants to display the statistics of an active tunnel on a DMVPN network. logging local Answer: BD Explanation/Reference: QUESTION 164 Which easy virtual networking configuration component significantly decreases network configuration? A. Router#show crypto isakmp sa D. virtual network trunk D. Easy Trunk B. VNET tags E.

Clear text D. ICMP path echo C. 200 B. Password protected C. Hashed Answer: C Explanation/Reference: QUESTION 168 What is the administrative distance for EBGP? A. Encrypted B. TCP connect D. HTTP B. 30 C. 20 Answer: D Explanation/Reference: . 70 D. ICMP echo Answer: B Explanation/Reference: QUESTION 167 In which form does PAP authentication send the username and password across the link? A.Which IP SLA operation can be used to measure round-trip delay for the full path and hop-by-hop round-trip delay on the network? A.

What is required in order for NDE to begin exporting data? A. Source . IPSEC AH header modification Answer: A Explanation/Reference: QUESTION 170 What is the optimal location from which to execute a debug command that produces an excessive amount of information? A. An AUX port Answer: A Explanation/Reference: QUESTION 171 A network engineer is configuring the router for NetF|ow data exporting. SNMP commands C. ipv6 duplication and conservation D. A console port D.QUESTION 169 Considering the 1Pv6 address independence requirements. rewriting of higher layer information B. checksum verification C. which process do you avoid when you use NPTv6 for translation A. Vty lines B.

B. Flow mask
C. Destination
D. Interface type
E. Traffic type
F. NetFIow version

Answer: C
Explanation/Reference:

QUESTION 172

Refer to the exhibit.

Router 1 cannot ping router 2 via the Frame Relay between them. Which two statements describe the
problems? (Choose two.)

A. Encapsulation is mismatched.
B. Frame Relay map is configured .
C. DLCI is active.
D. DLCI is inactive or deleted.
E. An access list is needed to allow ping.

Answer: AD
Explanation/Reference:

QUESTION 173

An engineer is using a network sniffer to troubleshoot DHCPv6 between a router and hosts on the LAN
with the following configuration:

Interface Ethernet0
|pv6 dhcp server DHCPSERVERPOOL rapid-commit
!
Which two DHCPv6 messages will appear in the sniffer logs?

A. reply
B. request
C. advertise
D. acknowledge
E. solicit
F. accept

Answer: DE
Explanation/Reference:
Q1:
At which layer does Cisco Express Fonrvarding use adjacency tables to populate addressing information?

A. Layer4
B. Layer 2
C. Layer 1
D. Layer 3

Answer: B

QUESTION 174

A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is less
than 64 KB. Which TCP feature ensures steady state throughput?

A. Window scaling
B. Network buffers
C. Round-trip timers
D. TCP acknowledgments

Answer: A
Explanation/Reference:

QUESTION 175

Drag and drop the challenge Handshake Authentication Protocol steps from the left into the correct order
in which they occur on the right.

A. Answer:

Answer:
Explanation/Reference:

QUESTION 176

Which two functionalities are specific to stateless NAT64? (Choose two.)

A. It does not conserve Ipv4 addresses. D. State or bindings are created on the translation . C. The administrator notices that Cisco Express Forwarding ARP requests are being sent to all destinations. instead Of the next-hop IP address. Low bandwidth usage B. IP route interference Answer: C Explanation/Reference: QUESTION 178 Exhibit: . Cisco Express Fonrvarding routing loop D. B. It uses address overloading. High bandwidth usage E. It provides 1-to-1 translation. High memory usage C. No requirement exists for the characteristics of Ipv6 address assignment. Answer: BC Explanation/Reference: QUESTION 177 A network administrator creates a static route that points directly to a multiaccess interface. Which issue might this configuration create? A. E.

Refer to the exhibit. ASBR . internal router B. showing complete command output. What type of OSPF router is Router A? A.

ABR D. edge router Answer: C Explanation/Reference: .C.