You are on page 1of 56

060220-00 Rev.

M
April 2011

OmniSwitch
Transceivers Guide

www.alcatel-lucent.com

This user guide contains SFP and XFP transceiver specifications and compatibility information for
the OmniSwitch 6250, 6850, 6850E, 6855, 6400, 9000, 9000E and the OmniStack 6200 Series of
switches . The information described in this guide is subject to change without notice.

Attention: Use of any transceivers other than those part numbers listed in the SFP and XFP
Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for
proper performance and may result in voiding the warranty for the affected platforms.

Copyright © 2011 by Alcatel-Lucent. All rights reserved. This document may not be reproduced in whole
or in part without the express written permission of Alcatel-Lucent.
Alcatel-Lucent® and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. Xylan®,
OmniSwitch®, OmniStack®, and Alcatel-Lucent OmniVista® are registered trademarks of Alcatel-Lucent.
OmniAccess™, Omni Switch/Router™, PolicyView™, RouterView™, SwitchManager™, VoiceView™,
WebView™, X-Cell™, X-Vision™, and the Xylan logo are trademarks of Alcatel-Lucent.
This OmniSwitch product contains components which may be covered by one or more of the following
U.S. Patents:
• U.S. Patent No. 6,339,830
• U.S. Patent No. 6,070,243
• U.S. Patent No. 6,061,368
• U.S. Patent No. 5,394,402
• U.S. Patent No. 6,047,024
• U.S. Patent No. 6,314,106
• U.S. Patent No. 6,542,507
• U.S. Patent No. 6,874,090

26801 West Agoura Road
Calabasas, CA 91301
(818) 880-3500 FAX (818) 880-3505
esd.support@alcatel-lucent.com
US Customer Support—(800) 995-2696
Internet—service.esd@alcatel-lucent.com

ii

OmniSwitch Transceivers Guide

April 2011

Contents
About This Guide ........................................................................................................... v

Supported Platforms ........................................................................................................... v
Who Should Read this Manual? ........................................................................................ vi
When Should I Read this Manual? .................................................................................... vi
What is Not in this Manual? .............................................................................................. vi
How is the Information Organized? ................................................................................. vii
Documentation Roadmap ................................................................................................. vii
Related Documentation ..................................................................................................... ix
Product Documentation ..................................................................................................... xi
Technical Support ............................................................................................................. xi
Chapter 1

Small Form-Factor Pluggables (SFPs) ................................................................... 1-1

In This Chapter ................................................................................................................1-1
SFP MSA Specification ..................................................................................................1-2
SFP Transceiver Installation and Removal .....................................................................1-3
Gigabit Ethernet Transceivers .........................................................................................1-5
Dual-Speed Ethernet Transceivers ..................................................................................1-8
Bi-directional Ethernet Transceivers ...............................................................................1-9
100 FX Ethernet Transceivers .......................................................................................1-12
CWDM Gigabit Ethernet Transceivers .........................................................................1-14
10-Gigabit SFP+ Transceivers ......................................................................................1-15
Chapter 2

Industrial Small Form Factor Pluggables (iSFPs) ............................................ 1-18

In This Chapter ..............................................................................................................1-18
Industrial Gigabit Ethernet Transceivers ......................................................................1-19
Industrial Bi-directional Ethernet Transceivers ............................................................1-22
Industrial 100 FX Ethernet Transceivers ......................................................................1-25
Industrial 10-Gigabit SFP+ Transceivers ......................................................................1-27
Chapter 3

10-Gigabit Small Form Factor Pluggables (XFPs) .......................................... 1-28

In This Chapter ..............................................................................................................1-28
XFP MSA Specification ................................................................................................1-29

OmniSwitch Transceivers Guide

April 2011

iii

Contents

XFP Transceiver Installation and Removal ..................................................................1-30
10-Gigabit Ethernet Transceivers .................................................................................1-31
Chapter 4

SFP Compatibility Matrix ........................................................................................ 1-34

OmniSwitch 9000 Series ...............................................................................................1-34
OmniSwitch 9000E Series ............................................................................................1-35
OmniSwitch 6855 Series ...............................................................................................1-36
OmniSwitch 6850 Series ...............................................................................................1-37
OmniSwitch 6850E Series ............................................................................................1-38
OmniSwitch 6400 Series ...............................................................................................1-40
OmniSwitch 6250 Series ...............................................................................................1-41
OmniStack 6200 Series .................................................................................................1-42
Chapter 5

XFP Compatibility Matrix ........................................................................................ 1-43

OmniSwitch 9000 Series ...............................................................................................1-43
OmniSwitch 9000E Series ............................................................................................1-43
OmniSwitch 6855 Series ...............................................................................................1-44
OmniSwitch 6850 Series ...............................................................................................1-44
OmniSwitch 6400 Series ...............................................................................................1-44
OmniSwitch 6250 Series ...............................................................................................1-44
OmniStack 6200 Series .................................................................................................1-45

iv

OmniSwitch Transceivers Guide

April 2011

About This Guide

This OmniSwitch Transceivers Guide provides specifications and compatibility information for the
supported OmniSwitch SFP and XFP transceivers for all OmniSwitch AOS 6 Release Products.

Attention: Use of any transceivers other than those part numbers listed in the SFP and XFP
Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for
proper performance and may result in voiding the warranty for the affected platforms.

Supported Platforms
This information in this guide applies to the following products:
• OmniSwitch 6250 Series
• OmniSwitch 6400 Series
• OmniSwitch 6850(E) Series
• OmniSwitch 6855 Series
• OmniSwitch 9000/9000E Series
• OmniStack 6200 Series

Unsupported Platforms
The information in this guide does not apply to the following products:
• OmniSwitch (original version with no numeric model name)
• OmniSwitch 6600 Series
• OmniSwitch 6800 Series
• OmniSwitch 7700/7800
• OmniSwitch 8800
• Omni Switch/Router
• OmniStack
• OmniAccess

OmniSwitch Transceivers Guide

April 2011

page v

This guide is designed to provide transceiver specification and compatibility information only and is not intended as a reference for any CLI commands or configuration information. This guide includes information about the supported OmniSwitch transceivers. page vi OmniSwitch Transceivers Guide April 2011 . Information on using WebView and OmniVista can be found in the context-sensitive on-line help available with those network management applications. web-based (WebView or OmniVista) or SNMP.Who Should Read this Manual? About This Guide Who Should Read this Manual? The audience for this user guide is network administrators and IT support personnel who need to provide network connectivity using SFP or XFP transceivers on an OmniSwitch. • SFP and XFP specifications • SFP and XFP compatibility information What is Not in this Manual? Procedures for switch management methods. For information on WebView and SNMP switch management methods consult the OmniSwitch Switch Management Guide. such as CLI. are outside the scope of this guide. You should have already stepped through the first login procedures and read the brief software overviews in the appropriate OmniSwitch Getting Started Guide and OmniSwitch Hardware Guide. Refer to the Documentation Roadmap for a list of available user guides. When Should I Read this Manual? Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are ready to provide connectivity using the supported transceivers.

and web-based management. Compatibility Information. and webbased management. This guide contains information on the switch directory structure. This guide provide specifications. we point you to the manual or manuals that will be most helpful to you. OmniSwitch Transceivers Guide April 2011 page vii . It also includes overview information on fundamental aspects of the switch. you will want to begin investigating basic aspects of its hardware and software. basic file and directory utilities. such as chassis. It also includes steps for common procedures. It is recommended that you read this guide before connecting your switch to the network. Stage 2: Gaining Familiarity with Basic Switch Functions Pertinent Documentation: Hardware Users Guides Switch Management Guide OmniSwitch Transceivers Guide Once you have your switch up and running. SFP or XPF. Specification Information. Under each stage. Each transceiver has an associated table providing individual specifications for all supported transceivers. A compatibility chart is provided for each transceiver specifying which modules or switch the transceiver is supported on. unlocking access control.About This Guide How is the Information Organized? How is the Information Organized? Chapters in this guide are broken down by transceiver type. The Switch Management Guide is the primary users guide for the basic software features on a single switch. illustrations. Information about switch hardware is provided in the Hardware Guide. such as hardware LEDs. and cooling fans. It provides information on unpacking the switch. power supplies. SNMP. Additional sub-sections are provided for the various types of transceivers. such as removing and installing switch components. At this time you should also familiarize yourself with the Release Notes that accompanied your switch. and descriptions of all hardware components. and setting up a password. Stage 1: Using the Switch for the First Time Pertinent Documentation: Getting Started Guides Release Notes The Getting Started Guide provides the basic information you need to unpack and identify the components of your shipment. This document includes important information on feature limitations that are not included in other user guides. Documentation Roadmap The OmniSwitch user documentation suite was designed to supply you with information at several critical junctures of the configuration process. CLI conventions. the software directory structure. Network Interface (NI) modules. switch access security. The following section outlines a roadmap of the manuals that will help you at each stage of the configuration process. setting the switch’s IP address. Chassis Management Modules (CMMs).

The Advanced Routing Configuration Guide includes configuration information for networks using advanced routing technologies (OSPF and BGP) and multicast routing protocols (DVMRP and PIM-SM). usage. and network routing protocols. procedures. related CLI command.Documentation Roadmap About This Guide Stage 3: Integrating the Switch Into a Network Pertinent Documentation: Network Configuration Guide Advanced Routing Configuration Guide When you are ready to connect your switch to the network. Anytime The OmniSwitch CLI Reference Guide contains comprehensive information on all CLI commands supported by the switch.1Q. default. you will need to learn how the OmniSwitch implements fundamental software features. Spanning Tree. This guide includes syntax. example. and examples on how standard networking technologies are configured in the OmniSwitch. such as 802. and CLI-to-MIB variable mapping information for all CLI commands supported by the switch. The Network Configuration Guide contains overview information. VLANs. This guide can be consulted anytime during the configuration process to find detailed and specific information on each CLI command. page viii OmniSwitch Transceivers Guide April 2011 .

• OmniSwitch 6850/6850E Series Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch 6850(E) shipment. Also provides information on the initial configuration of the switch. and Network Interface (NI) modules. power supplies. Also includes comprehensive information on assembling and managing stacked configurations. Also includes comprehensive information on assembling and managing stacked configurations. • OmniSwitch 6855 Series Hardware User Guide Complete technical specifications and procedures for all OmniSwitch 6855 Series chassis. • OmniSwitch 6250 Series Hardware Users Guide Detailed technical specifications and procedures for the OmniSwitch 6250 Series chassis and components. Also provides information on the initial configuration of the switch. fans. Also includes comprehensive information on assembling and managing stacked configurations. Includes syntax definitions. • OmniSwitch 6400 Series Hardware Users Guide Detailed technical specifications and procedures for the OmniSwitch 6400 Series chassis and components. • OmniSwitch 9000/9000E Series Hardware Users Guide Complete technical specifications and procedures for all OmniSwitch 9000/9000E Series chassis. • OmniSwitch 6855 Series Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch 6855 shipment. power supplies. Also provides information on fundamental aspects of OmniSwitch software architecture. and fans.Also provides information on the initial configuration of the switch. and fans. OmniSwitch Transceivers Guide April 2011 page ix . • OmniSwitch 6400 Series Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch 6400 shipment. Also provides information on the initial configuration of the switch.About This Guide Related Documentation Related Documentation The following are the titles and descriptions of all the related OmniSwitch AOS Release 6 user manuals: • OmniSwitch 6250 Series Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch 6250 shipment. examples. default values. power supplies. • OmniSwitch CLI Reference Guide Complete reference to all CLI commands supported on the OmniSwitch Series switches. • OmniSwitch 6850/6850E Series Hardware User Guide Complete technical specifications and procedures for all OmniSwitch 6850(E) Series chassis. • OmniSwitch 9000/9000E Series Getting Started Guide Describes the hardware and software procedures for getting an OmniSwitch 9000/9000E Series up and running. usage guidelines and CLI-to-MIB variable mappings.

authenticated switch access. Field Notices Includes information published by Alcatel-Lucent’s Customer Support group.Related Documentation About This Guide • OmniSwitch AOS Release 6 Switch Management Guide Includes procedures for readying an individual switch for integration into a network. Layer 3 information (routing protocols. and other important information on the features supported in the current release and any limitations to their support. system configuration. image rollback protections. and using web management software (WebView). and OSPF. • Release Notes Includes critical open Problem Reports. security options (authenticated VLANs). Chapters cover multicast routing (DVMRP and PIM-SM). and link aggregation. Topics include the software directory architecture. Chapters cover Layer 2 information (Ethernet and VLAN configuration). using SNMP. such as RIP). feature exceptions. • Technical Tips. • OmniSwitch Transceivers Guide Includes SFP and XFP transceiver specifications and product compatibility information. managing switch files. • OmniSwitch AOS Release 6 Advanced Routing Configuration Guide Includes network configuration procedures and descriptive information on all the software features and protocols included in the advanced routing software package. • OmniSwitch AOS Release 6 Network Configuration Guide Includes network configuration procedures and descriptive information on all the major software features and protocols included in the base software package. page x OmniSwitch Transceivers Guide April 2011 . Quality of Service (QoS).

com.com. OmniSwitch Transceivers Guide April 2011 page xi . All documentation is in PDF format and requires the Adobe Acrobat Reader program for viewing. call us at 1-800-995-2696. Additionally.About This Guide Product Documentation Product Documentation Some products are shipped with documentation included on a User Manual CD that accompanies the switch. with 24-hour-a-day access to Alcatel-Lucent’s Service and Support web page. Otherwise pages may print with slightly smaller margins. When printing pages from the documentation PDFs.alcatel-lucent.adobe. To verify that you are using Acrobat Reader with the global search option. and manuals. For more information on Alcatel-Lucent’s Service Programs. You’ll also receive regular software updates to maintain and maximize your Alcatel-Lucent product’s features and functionality and on-site hardware replacement through our global network of highly qualified service delivery partners. This CD also includes documentation for other Alcatel-Lucent data enterprise products. open a new case or access helpful release notes. In order to take advantage of the documentation CD’s global search feature.com. see our web page at service. de-select Fit to Page if it is selected in your print dialog. Note.support@alcatel-lucent. or email us at esd. look for the following button in the toolbar: Note. it is recommended that you select the option for searching PDF files before downloading Acrobat Reader freeware. All products are shipped with a Product Documentation Card that provides details for downloading documentation for all OmniSwitch and other Alcatel-Lucent data enterprise products.esd. technical bulletins. you’ll be able to view and update any case (open or closed) that you have reported to Alcatel-Lucent’s technical support. Acrobat Reader freeware is available at www. Technical Support An Alcatel-Lucent service agreement brings your company the assurance of 7x24 no-excuses technical support.

Technical Support page xii About This Guide OmniSwitch Transceivers Guide April 2011 .

See “SFP MSA Specification” on page 1-2 • SFP Transceiver Installation. see “XFP Compatibility Matrix” on page 5-42. see “SFP Compatibility Matrix” on page 4-34. OmniSwitch Transceivers Guide April 2011 page 1-1 . see the appropriate OmniSwitch Hardware Guide. For additional details about OmniSwitch modules. Copper-based and fiber-based optical SFPs can be mixed on the same module. • CWDM Gigabit Ethernet Transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications.1 Small Form-Factor Pluggables (SFPs) OmniSwitch Series switches use both copper-based and fiber-based optical Small Form Factor Pluggable (SFP) transceivers. See “SFP Transceiver Installation and Removal” on page 1-3 • Gigabit Ethernet Transceivers. SFP specifications in this chapter include: • SFP MSA Specifications. See “CWDM Gigabit Ethernet Transceivers” on page 1-14. see the appropriate Hardware Guide. • Bi-directional Ethernet Transceivers. For information on OmniSwitch SFP compatibility. See “Gigabit Ethernet Transceivers” on page 1-5. See “Bi-directional Ethernet Transceivers” on page 1-9. • 10-Gigabit SFP+ Transceivers. For information on OmniSwitch XFP compatibility. See “Dual-Speed Ethernet Transceivers” on page 1-8. • Dual-Speed Ethernet Transceivers. • 100-FX Ethernet Transceivers. See “10-Gigabit SFP+ Transceivers” on page 1-15 For information on installing and managing OmniSwitch hardware. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported SFP transceivers. See “100 FX Ethernet Transceivers” on page 1-12.

manufacturer and other information. For information on installing SFPs. refer to the documentation included with the transceiver. The connector provides the interface for the hot pluggable SFP module.SFP MSA Specification Small Form-Factor Pluggables (SFPs) SFP MSA Specification The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. stand interfaces. This diagram is a representation only. Small Form Factor Pluggable (SFP) page 1-2 OmniSwitch Transceivers Guide April 2011 . Each SFP module contains a serial interface to provide identification information that describes the SFP capabilities. the physical appearance of the actual module may vary slightly. The SFP connector consists of a 20-pin receptacle and an SFP housing cage.

Slide the SFP straight into the slot until the module clicks firmly into place. Note: Never force the transceiver in or out of the transceiver slot. ensure that the wrist strap touches your skin. you must first open the SFP’s hinged face to approximately ninety degrees. Refer to your hardware user guide for details. wait for a minimum of 5 seconds before re-inserting any transceiver into the same port. When inserting a SFP. this can be used. you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage. Attach the other end of the strap to the chassis. ensure that the wrist strap touches your skin. be sure to replace the protective rubber cover (provided) when the SFP is not in use. If using a wrist strap. If using a wrist strap. If your chassis provides a grounding lug.Hinged OmniSwitch Transceivers Guide April 2011 page 1-3 . this can be used. Eye Safety: SFP transceivers are international Class 1 laser products and are eye-safe devices when operated within the limits of manufacturers’ specifications. Dust Exposure: To reduce the risk of dust exposure and physical damage. Then. SFP Module SFP . Operating SFP transceivers in a manner inconsistent with intended usage and specification may result in hazardous radiation exposure. This allows sufficient time for software to detect the removal of the transceiver. Refer to your hardware user guide for details. grasp the hinged face and carefully pull the SFP straight out of the slot. Attach the other end of the strap to the chassis. ESD Caution: Before handling the module. be sure that the hinged face is closed. Interface Slot To remove.Small Form-Factor Pluggables (SFPs) SFP Transceiver Installation and Removal SFP Transceiver Installation and Removal Follow the instructions below for the appropriate SFP type. If your chassis provides a grounding lug. Note: After removing a transceiver.

Slide the transceiver straight into the slot until the module clicks firmly into place. align the transceiver with the transceiver slot on the NI module. Carefully slide the transceiver back until it clicks into place. when inserting. bail delatch must be closed. this is an indication that the connectors are firmly seated. as shown. you must first pull down on the bail wire delatch. Grip the wire delatch while it is in this open position and carefully pull the transceiver straight out of the slot. refer to the diagram for more information. use the clip end of the ejector tool to carefully pull the transceiver straight out and away from the NI module. or closed position. The transceiver will disengage from the connectors and eject slightly.SFP Transceiver Installation and Removal Small Form-Factor Pluggables (SFPs) To install.Bail Wire To install.Ejector Button page 1-4 OmniSwitch Transceivers Guide April 2011 . SFP Transceiver Transceiver Slot Bail Wire Delatch (Shown in open “removal” position.) Network Interface (NI) Module SFP . align the transceiver with the transceiver slot on the NI module. as shown. To remove. Transceiver Slot Ejector Dust Cover SFP . Be sure that the bail wire delatch is in the up. use the ejector tool (provided with each switch chassis) to push the transceiver’s ejector button. Network Interface (NI) Module SFP Transceiver To remove. The ejector button is located just below the transceiver port. Once disengaged.

3z.5 to -4 dBm Receiver Sensitivity -17 dBm Transmission Distance ~275 m on 62. SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -9.Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers Gigabit Ethernet Transceivers SFP-GIG-SX Gigabit SFP Optical Transceiver.5/125µm ~550 m on 50/125µm Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported SFP-GIG-LX Gigabit SFP Optical Transceiver. Connector types LC Standards supported 802.5 to -3 dBm Receiver Sensitivity -20 dBm Transmission Distance ∼10 km Operating Temperature -40 ºC to 85 ºC / 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 1-5 . Connector Type LC Standards Supported 802. SFP MSA Connections supported 1000Base-LX Fiber Type SMF Wavelength 1310 nm Optical Power Output -9.3z.

3z. Connector Type LC Standards Supported 802.3z. SFP MSA Connections Supported 1000Base-LH40r Fiber Type SMF Wavelength 1310 nm Optical Power Output -2 to +3 dBm Reciever Sensitivity -22 dBm Transmission Distance ~40 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported page 1-6 OmniSwitch Transceivers Guide April 2011 .) SFP-GIG-LH70 Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers (cont. SFP MSA Connections Supported 1000Base-LH70 Fiber Type SMF Wavelength 1550 nm Optical Power Output 0 to +5 dBm Receiver Sensitivity -22 dBm Transmission Distance ~70 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported SFP-GIG-LH40 Gigabit SFP Optical Transceiver.

CAT5e.3z. SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output - Receiver Sensitivity - Transmission Distance ~2 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported SFP-GIG-T Gigabit SFP Copper Transceiver. Connector Type LC Standards Supported 802. SFP MSA Connections supported 1000Base-T Cable Type CAT5.Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers Gigabit Ethernet Transceivers (cont.3z.) SFP-GIG-EXTND Gigabit SFP Optical Transceiver. CAT6 Transmission Distance ∼100 m Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 1-7 . Connector Type RJ-45 Standards Supported 802.

3z. Connector Type LC Standards Supported 802.3ah.5 to -3 dBm Receiver Sensitivity 100Base-FX: -28 dBm 1000Base-LX: -22 dBm Transmission Distance 550 m at 1000 Mbps 2 km at 100 Mbps Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported SFP-DUAL-SM10 Dual-Speed SFP Optical Transceiver. SFP MSA Connections Supported 100Base-FX. 1000Base-LX Fiber Type SMF Wavelength 1310 nm Average Power Output 100Base-FX: -15 to -8 dBm 1000Base-LX: -9. Connector Type LC Standards Supported 802. 802.3ah.Dual-Speed Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Dual-Speed Ethernet Transceivers SFP-DUAL-MM Dual-Speed SFP Optical Transceiver.3z.5 to -3 dBm Receiver Sensitivity 100Base-FX: -28 1000Base-LX: -22 Transmission Distances 10 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported page 1-8 OmniSwitch Transceivers Guide April 2011 . 802. SFP MSA Connections Supported 100Base-FX. 1000Base-LX Fiber Type MMF Wavelength 1310 nm Average Power Output 100Base-FX: -20 to -14 dBm 1000Base-LX: -11.

3ah. Connector Type SC Standards Supported 802. ITU-T G.Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers SFP-100-BX20LT Bi-Directional SFP Optical Transceiver.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-100-BX20NU SFP-100-BX20NU Bi-Directional SFP Optical Transceiver. ITU-T G. Connector Type SC Standards Supported 802. SFP MSA. SFP MSA.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1310 nm Receive: 1550 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-100-BX20LT OmniSwitch Transceivers Guide April 2011 page 1-9 .3ah.

SFP MSA.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1310 nm Receive: 1550 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-100-BXLC-D page 1-10 OmniSwitch Transceivers Guide April 2011 . ITU-T G.Bi-directional Ethernet Transceivers Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers (cont.) SFP-100-BXLC-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802. Connector Type LC Standards Supported 802.3ah.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-100-BXLC-U SFP-100-BXLC-U Bi-Directional SFP Optical Transceiver.3ah. SFP MSA. ITU-T G.

Small Form-Factor Pluggables (SFPs) Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers (cont. Connector Type LC Standards Supported 802.5 dBm Transmission Distance ~10 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-GIG-BX-D OmniSwitch Transceivers Guide April 2011 page 1-11 .5 dBm Transmission Distance ~10 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-GIG-BX-U SFP-GIG-BX-U Bi-Directional SFP Optical Transceiver. SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1310 nm Receive: 1490 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19. SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1490 mm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.3ah. Connector Type LC Standards Supported 802.) SFP-GIG-BX-D Bi-Directional SFP Optical Transceiver.3ah.

5/125µm ~2 km on 50/125µm Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported SFP-100-LC-SM15 SFP Optical Transceiver.3u.5/125µm -22 to -14 dBm on 50/125µm Transmission Distance ~2 km on 62. SFP MSA Connections Supported 100Base-FX Fiber Type SMF Wavelength (nm) 1310 nm Optical Power Output -15 to -8 dBm Receiver Sensitivity -34 dBm Transmission Distance ~15 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported page 1-12 OmniSwitch Transceivers Guide April 2011 . Connector Type LC Standards Supported 802. Connector Type LC Standards Supported 802.100 FX Ethernet Transceivers Small Form-Factor Pluggables (SFPs) 100 FX Ethernet Transceivers SFP-100-LC-MM SFP Optical Transceiver.3u. SFP MSA Connections supported 100Base-FX Fiber Type MMF Wavelength 1310 nm Optical Power Output -19 to -14 dBm on 62.

) SFP-100-LC-SM40 SFP Optical Transceiver. Connector Type LC Standards Supported 802. SFP MSA Connections Supported 100Base-FX Fiber Type SMF Wavelength 1310 nm Optical Power Output -15 to -8 dBm Receiver Sensitivity -34 dBm Transmission Distances ~40 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 1-13 .Small Form-Factor Pluggables (SFPs) 100 FX Ethernet Transceivers 100 FX Ethernet Transceivers (cont.3u.

1490.3z. 1610 Optical Power Output -2 to +3 dBm Receiver Sensitivity -24 dBm Transmission Distances ~62 km Operating Temperature -5 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported page 1-14 OmniSwitch Transceivers Guide April 2011 . 1550. 1510.CWDM Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFPs) CWDM Gigabit Ethernet Transceivers . 1590. 1570. Connector Type LC Standards Supported 802. SFP MSA Connections Supported 1000Base-LX Fiber Type SMF Wavelength 1470. 1530. CWDMs are hot-pluggable and are available for long-reach applications. SFP-GIG-CWD Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber over various wavelengths.

5 dBm Receiver Sensitivity -12.2 to 0.Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers 10-Gigabit SFP+ Transceivers SFP-10G-SR 10-Gigabit SFP+ Optical Transceiver.3 dBm Receiver Sensitivity -11.6 dBm Transmission Distance ~ 10 km Operating Temperature 0 ºC to 70ºC Digital Diagnostic Monitoring Supported OmniSwitch Transceivers Guide April 2011 page 1-15 . Connector Type LC Standards Supported 802.3 Clause 52 Connections supported 10GBase-SR Fiber Type MMF Wavelength 850 nm Optical Power Output -7.3 Clause 52 Connections supported 10GBase-LR Fiber Type SMF Wavelength 1310 nm Optical Power Output -8.3 to -1.1 dBm Transmission Distance ~ 300 m Operating Temperature 0 ºC to 70ºC Digital Diagnostic Monitoring Supported SFP-10G-LR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.

Connector Type LC Standards Supported 802.3ae Connections supported 10GBase-E Fiber Type SMF Wavelength 1550 nm Optical Power Output -4.1 dBm Transmission Distance ~ 40 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported SFP-10G-LRM 10-Gigabit SFP+ Optical Transceiver.10-Gigabit SFP+ Transceivers Small Form-Factor Pluggables (SFPs) SFP-10G-ER 10-Gigabit SFP+ Optical Transceiver.7 to 4.5 dBm Receiver Sensitivity -6.3aq Connections supported 10GBase-LRM Fiber Type MMF Wavelength 1310 nm Optical Power Output -6. Connector Type LC Standards Supported 802.5 to .0 dBm Receiver Sensitivity -14.5 dBm Transmission Distance ~ 220 m Operating Temperature 0 ºC to 70ºC Digital Diagnostic Monitoring Supported page 1-16 OmniSwitch Transceivers Guide April 2011 .

Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers SFP-10G-C 10-Gigabit SFP+ Copper Transceiver. OmniSwitch Transceivers Guide April 2011 page 1-17 . 1m. Connector Type Direct Attached Standards Supported 802.3ae Cable Length 30cm. 10m 1 Digital Diagnostic Monitoring Not Supported 1 Check for availability of lengths. 7m. 3m.

see the appropriate OmniSwitch Hardware Guide.2 Industrial Small Form Factor Pluggables (iSFPs) OmniSwitch Series switches use both copper-based and fiber-based optical Industrial Small Form Factor Pluggable (SFP) transceivers. See “Bi-directional Ethernet Transceivers (cont. • Industrial 100-FX Ethernet Transceivers. iSFP specifications in this chapter include: • Industrial Gigabit Ethernet Transceivers. See “Industrial Gigabit Ethernet Transceivers” on page 2-19. see the appropriate OmniSwitch Hardware Guide. Additionally. see “SFP Compatibility Matrix” on page 4-34. Industrial SFPs are designed to operate at an increased temperature range of -40 ºC to 85 ºC. Copper-based and fiber-based optical SFPs can be mixed on the same module. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported iSFP transceivers.)” on page 2-23. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications. • Industrial 10-Gigabit Ethernet Transceivers. For additional details about OmniSwitch modules. See “Industrial 10-Gigabit SFP+ Transceivers” on page 2-27 For information on installing and managing OmniSwitch hardware. OmniSwitch Transceivers Guide April 2011 page 2-18 . For information on OmniSwitch SFP compatibility. See “Industrial Bi-directional Ethernet Transceivers” on page 2-22. • Industrial Bi-directional Ethernet Transceivers.

SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -9. Connector types LC Standards supported 802.5 to -3 dBm Receiver Sensitivity -20 dBm Transmission Distance ∼10 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 2-19 .5/125µm ~550 m on 50/125µm Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported iSFP-GIG-LX Industrial Gigabit SFP Optical Transceiver.5 to -3.5 dBm Receiver Sensitivity -18 dBm Transmission Distance ~275 m on 62. SFP MSA Connections supported 1000Base-LX Fiber Type SMF Wavelength 1310 nm Average Output Power -9.3z.Industrial Small Form Factor Pluggables (iSFPs) Industrial Gigabit Ethernet Transceivers Industrial Gigabit Ethernet Transceivers iSFP-GIG-SX Industrial Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z.

SFP MSA Connections Supported 1000Base-LH40 Fiber Type SMF Wavelength 1310 nm Optical Power Output -2 to +3 dBm Receiver Sensitivity -22 dBm Transmission Distance ~40 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported page 2-20 OmniSwitch Transceivers Guide April 2011 .3z. Connector Type LC Standards Supported 802.) iSFP-GIG-LH70 Industrial Gigabit SFP Optical Transceiver. SFP MSA Connections Supported 1000Base-LH70 Fiber Type SMF Wavelength 1550 nm Optical Power Output 0 to +5 dBm Receiver Sensitivity -22 dBm Transmission Distance ~70 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported iSFP-GIG-LH40 Industrial Gigabit SFP Optical Transceiver.Industrial Gigabit Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) Industrial Gigabit Ethernet Transceivers (cont.3z. Connector Type LC Standards Supported 802.

Industrial Small Form Factor Pluggables (iSFPs) Industrial Gigabit Ethernet Transceivers iSFP-GIG-T Industrial Gigabit SFP Copper Transceiver. CAT6 Transmission Distance ∼100 m Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 2-21 . SFP MSA Connections supported 1000Base-T Cable Type CAT5. CAT5e.3z. Connector Type RJ-45 Standards Supported 802.

ITU-T G. Connector Type SC Standards Supported 802. SFP MSA.Industrial Bi-directional Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) Industrial Bi-directional Ethernet Transceivers iSFP-100-BX-D Industrial Bi-Directional SFP Optical Transceiver. SFP MSA. ITU-T G. Connector Type SC Standards Supported 802.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported Notes Designed for use with iSFP-100-BX-U iSFP-100-BX-U Industrial Bi-Directional SFP Optical Transceiver.3ah.3ah.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1310 nm Receive: 1550 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported Notes Designed for use with iSFP-100-BX-D page 2-22 OmniSwitch Transceivers Guide April 2011 .

ITU-T G.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1310 nm Receive: 1550 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 85ºC Digital Diagnostic Monitoring Supported Notes Designed for use with iSFP-100-BXLC-D OmniSwitch Transceivers Guide April 2011 page 2-23 .Industrial Small Form Factor Pluggables (iSFPs) Industrial Bi-directional Ethernet Transceivers Bi-directional Ethernet Transceivers (cont. SFP MSA. SFP MSA. Connector Type LC Standards Supported 802.) iSFP-100-BXLC-D Industrial Bi-Directional SFP Optical Transceiver.3ah.3ah. ITU-T G.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 85 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with iSFP-100-BXLC-U iSFP-100-BXLC-U Industrial Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.

SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1490 mm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.5 dBm Transmission Distance ~10 km Operating Temperature -40 ºC to 85 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with iSFP-GIG-BX-D page 2-24 OmniSwitch Transceivers Guide April 2011 .Industrial Bi-directional Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) iSFP-GIG-BX-D Industrial Bi-Directional SFP Optical Transceiver.5 dBm Transmission Distance ~10 km Operating Temperature -40 ºC to 85 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with iSFP-GIG-BX-U iSFP-GIG-BX-U Industrial Bi-Directional SFP Optical Transceiver.3ah. Connector Type LC Standards Supported 802. SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1310 nm Receive: 1490 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.3ah. Connector Type LC Standards Supported 802.

Industrial Small Form Factor Pluggables (iSFPs) Industrial 100 FX Ethernet Transceivers Industrial 100 FX Ethernet Transceivers iSFP-100-MM Industrial SFP Optical Transceiver.3u. Connector Type LC Standards Supported 802. SFP MSA Connections supported 100Base-FX Fiber Type MMF Wavelength 1310 nm Optical Power Output -20 to -14 dBm Receiver Sensitivity -30 dBm Transmission Distance ~ 2 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Not Supported iSFP-100-SM15 Industrial SFP Optical Transceiver. Connector Type LC Standards Supported 802.3u. SFP MSA Connections Supported 100Base-FX Fiber Type SMF Wavelength (nm) 1310 nm Optical Power Output -15 to -8 dBm Receiver Sensitivity -34 dBm Transmission Distance ~15 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 2-25 .

3u. Connector Type LC Standards Supported 802. SFP MSA Connections Supported 100Base-FX Fiber Type SMF Wavelength 1310 nm Optical Power Output -15 to -8 dBm Receiver Sensitivity -34 dBm Transmission Distances ~40 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Not Supported page 2-26 OmniSwitch Transceivers Guide April 2011 .Industrial 100 FX Ethernet Transceivers Industrial Small Form Factor Pluggables (iSFPs) Industrial 100 FX Ethernet Transceivers (cont.) iSFP-100-SM40 Industrial SFP Optical Transceiver.

3 dBm Transmission Distance ~ 10 km Operating Temperature -40 ºC to 85ºC Digital Diagnostic Monitoring Supported iSFP-10G-C 10-Gigabit SFP+ Copper Direct Attached Copper Cable.3ae Cable Length 30cm.Industrial Small Form Factor Pluggables (iSFPs) Industrial 10-Gigabit SFP+ Transceivers Industrial 10-Gigabit SFP+ Transceivers iSFP-10G-LR Industrial 10-Gigabit SFP+ Optical Transceiver. 3m.5 dBm Receiver Sensitivity -10. 10m Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 2-27 .2 to 0. Connector Type Direct Attached Standards Supported 802. Connector Type LC Standards Supported 802.3 Clause 52 Connections supported 10GBase-LR Fiber Type SMF Wavelength 1310 nm Optical Power Output -8.

For additional details about OmniSwitch modules. OmniSwitch Transceivers Guide April 2011 page 3-28 . see the appropriate OmniSwitch Hardware Guide.3 10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Small Form Factor Pluggables (XFPs) are fiber-based optical transceivers. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported XFP transceivers. For information on OmniSwitch XFP compatibility. See “XFP MSA Specification” on page 3-29 • XFP Transceiver Installation. See “10-Gigabit Ethernet Transceivers” on page 3-31. see “XFP Compatibility Matrix” on page 5-42. see the appropriate Hardware Guide. • 10-Gigabit Ethernet Transceivers. XFPs are fully hotswappable and are available for both short-reach and long-reach applications. For information on installing and managing OmniSwitch hardware. See “XFP Transceiver Installation and Removal” on page 3-30. XFP specifications in this chapter include: • XFP MSA Specificaton.

manufacturer and other information. The connector provides the interface for the hot pluggable XFP module.10-Gigabit Small Form Factor Pluggables (XFPs) XFP MSA Specification XFP MSA Specification The 10-Gigabit Small Form-Factor Pluggable (XFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. standard interfaces. refer to the documentation included with the transceiver. For information on installing XFPs. 10-Gigabit Small Form Factor Pluggable (XFP) Eye Safety XFP transceivers are international Class 1 laser products and are eye-safe devices when operated within the limits of manufacturers’ specifications. OmniSwitch Transceivers Guide April 2011 page 3-29 . Operating XFP transceivers in a manner inconsistent with intended usage and specification may result in hazardous radiation exposure. Each XFP module contains a serial interface to provide identification information that describes the XFP capabilities. the physical appearance of the actual module may vary slightly. This diagram is a representation only. The XFP connector consists of a 30-pin receptacle and an XFP housing cage.

be sure to replace the protective rubber cover (provided) when the XFP is not in use. you must first open the XFP’s hinged bail latch to approximately ninety degrees. when inserting. Then.) ( XFP . be sure that the bail latch is closed. Eye Safety: XFP transceivers are international Class 1 laser products and are eye-safe devices when operated within the limits of manufacturers’ specifications. Dust Exposure: To reduce the risk of dust exposure and physical damage. this can be used. Note: Never force the transceiver in or out of the transceiver slot. this can be used. bail delatch must be closed. Attach the other end of the strap to the chassis. ensure that the wrist strap touches your skin. Attach the other end of the strap to the chassis. ensure that the wrist strap touches your skin. XFP Transceiver Transceiver Slot Bail Wire Shown in open “removal” position. Slide the XFP straight into the slot until the module clicks firmly into place. you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage. Note: After removing a transceiver. If your chassis provides a grounding lug. This allows sufficient time for software to detect the removal of the transceiver.XFP Transceiver Installation and Removal 10-Gigabit Small Form Factor Pluggables (XFPs) XFP Transceiver Installation and Removal Follow the instructions below when installing an XFP transceiver.Bail Wire page 3-30 OmniSwitch Transceivers Guide April 2011 . If your chassis provides a grounding lug. grasp the hinged face and carefully pull the XFP straight out of the slot. ESD Caution: Before handling the module. wait for a minimum of 5 seconds before re-inserting any transceiver into the same port. If using a wrist strap. To remove. Refer to your hardware user guide for details. To install. Operating XFP transceivers in a manner inconsistent with intended usage and specification may result in hazardous radiation exposure. If using a wrist strap. Refer to your hardware user guide for details.

Connector Type LC Standards Supported 802.10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers 10-Gigabit Ethernet Transceivers XFP-10G-SR 10-Gigabit XFP Optical Transceiver. Connector Type LC Standards Supported 802. XFP MSA Connections Supported 10GBase-SR Fiber Type MMF Wavelength 850 nm Optical Power Output -7.5 dBm Receiver Sensitivity -16 dBm Transmission Distances ∼ 10 km Power Consumption 2.2 to .5 W Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported XFP-10G-LR 10-Gigabit XFP Optical Transceiver. XFP MSA Connections Supported 10GBase-LR Fiber Type SMF Wavelength 1310 nm Optical Power Output -8. Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported OmniSwitch Transceivers Guide April 2011 page 3-31 .3ae.5 W Max.3 to -1.0 dBm Receiver Sensitivity -9.9 dBm Transmission Distance ∼ 300 m (with OM3 fiber) Power Consumption 1.3ae.

7 to +4 dBm Receiver Sensitivity -15. Connector Type LC Standards Supported 802. XFP MSA Connections Supported 10GBase-ZR Fiber Type SMF Wavelength 1550 nm Optical Power Output 0 to +4 dBm Receiver Sensitivity -24 dBm Transmission Distance ∼ 80 km Power consumption 3.5 W Max. Operating Temperature -5 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported page 3-32 OmniSwitch Transceivers Guide April 2011 .3ae.) XFP-10G-ER40 10-Gigabit XFP Optical Transceiver. Connector type LC Standards Supported 802.8 dBm Transmission Distance ∼ 40 km Power Consumption 3.10-Gigabit Ethernet Transceivers 10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers (cont.3ae. XFP MSA Connections Supported 10GBase-ER Cable Type SMF Wavelength 1550 nm Optical Power Output -4.5 W Max. Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported XFP-10G-ZR80 10-Gigabit XFP Optical Transceiver.

Connector Type CX4 Standards Supported 802.33 Optical Power Output -3 to +3 dBm Receiver Sensitivity -23 or -27 dBm Transmission Distance ∼ 80 km Power consumption <3. C-Band optical transceiver supporting single-mode fiber over various wavelengths.1546.1549. DWDMs are hot-pluggable and are available for long-reach applications.10-Gigabit Small Form Factor Pluggables (XFPs) 10-Gigabit Ethernet Transceivers 10-Gigabit Ethernet Transceivers (cont. This is due to the time required for the transceiver to reach its optimum operating temperature.12 Channel 59 .32 Channel 37 .72 Channel 38 .3ak Transmission Distance ∼15 m Digital Diagnostic Monitoring Not Supported Notes InfiniBand type cables not supported. 100GHz ITU Grid.5W Operating Temperature -5 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported Notes The transmitter becomes operational within 60 seconds of power-up.) XFP-10G-CX4 10-Gigabit XFP Copper Transceiver. XFP-10G-DWDM Dense Wavelength Division Multiplexing (DWDM). OmniSwitch Transceivers Guide April 2011 page 3-33 .1546. XFP MSA Connections supported 10GBase-CX4 Cable Type Standard CX4 copper cables compliant with IEEE 802.92 Channel 39 .1530.3ak. Connector type LC Standards Supported XFP MSA Fiber Type SMF Wavelength Channel 35 .1547.

5 6.5 Not supported SFP-100-LC-SM40 6.1.3.1 SFP-GIG-T 1 1.1.1.1. OmniSwitch Transceivers Guide April 2011 page 4-34 .5 All SFP-GIG-LH70 6.1.5 Not supported SFP-100-BX20NU 6.5 Not supported SFP-100-LC-MM 6.5 6.1 SFP-GIG-BX-U 6.1.3 SFP-DUAL-SM10 6. Supports 10/100/1000 Mbits.5 All SFP-GIG-LX 6.1.5 All SFP-GIG-CWD 6.5 Not supported SFP-100-BXLC-D 6.3.5 All SFP-GIG-EXTND 6.1.1 6.1.1.1.3.5 6.1.5 Not supported SFP-100-LC-SM15 6.1 6.1.5 Not supported SFP-GIG-BX-D 6.1.1.4 SFP Compatibility Matrix OmniSwitch 9000 Series The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 9000 Series: SFP OS9-GNI-C20L OS9-GNI-U24 SFP-GIG-SX 6.1.3.5 All 6.3 SFP-100-BX20LT 6.5 Not supported SFP-100-BXLC-U 6.1.3 SFP-DUAL-MM 6.1.5 All SFP-GIG-LH40 6.1.

Speed must be hardcoded to 1000 Mbits for support on OS9-XNI-U12E. OmniSwitch Transceivers Guide April 2011 page 4-35 .SFP Compatibility Matrix OmniSwitch 9000E Series OmniSwitch 9000E Series The following table shows the Ethernet transceiver configurations and minimum release required for support on the OmniSwitch 9000E Series: SFP OS9-GNI-U24E OS9-XNI-U12E 1 6.4.4 6.4.4.4.4.4 SFP-DUAL-MM 6.1 - SFP-10G-SR - 6.4.4.4.4.3 SFP-10G-ER - 6.4.4 6.4.4 6.1 6.4.3 SFP-10G-LRM - 6.4.4.1 - SFP-DUAL-SM10 6.4.1 6.1 6.1 - SFP-100-BX20LT Not supported - SFP-100-BX20NU Not supported - SFP-100-BXLC-D Not supported - SFP-100-BXLC-U Not supported - SFP-100-LC-MM Not supported - SFP-100-LC-SM15 Not supported - SFP-100-LC-SM40 Not supported - SFP-GIG-BX-D 6.3 SFP-10G-LR - 6.4 1 6.4. Supports 10/100/1000 Mbits.4.4.1 6.4 6.3 SFP-GIG-SX SFP-GIG-LX SFP-GIG-LH401 SFP-GIG-LH70 1 SFP-GIG-EXTND 1 SFP-GIG-CWD1 SFP-GIG-T 1.1 6.4.1 - SFP-GIG-BX-U 6.1 6. 2.1 6.4.3 SFP-10G-C - 6.4 6.4.4.2 1.4.

3.2 iSFP-GIG-LH40 6.2 iSFP-100-BXLC-U 1 6.4.2 SFP-10G-SR5.3.3.2 iSFP-100-MM1 6.2 iSFP-GIG-BX-U 6.4.4.3.2 iSFP-10G-LR iSFP-10G-C 5 6.2 iSFP-100-SM40 1 6.2 iSFP-100-BXLC-D 1 6.6 6.2 5.2 iSFP-GIG-T iSFP-100-BX-D 6.3.6 SFP-10G-ER 6.3.4.3.2 iSFP-GIG-LH70 6.2 iSFP-100-SM15 1 6.4.6 6.3 5.3.3 iSFP-100-BX-U 6. Supported on OS6855-U24X only.3. 6.2 1 6. * 10/100/1000 Mbps SFP transceivers are not supported on 10-Gigabit SFP+ ports.2 5 6.3 iSFP-GIG-BX-D 6.4. page 4-36 OmniSwitch Transceivers Guide April 2011 .4. Does not support industrial temperature ranges. 5. 4.OmniSwitch 6855 Series SFP Compatibility Matrix OmniSwitch 6855 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6855: SFP OS6855 iSFP-GIG-SX 6. Supports maximum of 22 Copper SFPs on OS6855-U24X.4.4. Not supported on combo ports. Supports maximum of 4 Copper SFPs on OS6855-U10.4. 2.4.4.2 1.4 6.2 iSFP-GIG-LX 6.2 iSFP-100-BX-D iSFP-100-BX-U1 6.3 SFP-10G-LRM All other non-industrial SFPs Not Supported 1.3. 3.2. Supports maximum of 8 Copper SFPs on OS6855-U24.

3 SFP-DUAL-MM 6.1.1 SFP-GIG-BX-U 6.1.3 SFP-GIG-EXTND All 6. OmniSwitch Transceivers Guide April 2011 page 4-37 .3 SFP-100-BX20LT Not supported 6.1.1.2 SFP-100-BXLC-U Not supported 6.3.4.3 SFP-DUAL-SM10 6.1 SFP-GIG-T 1.1.3 SFP-100-LC-SM15 Not supported 6.1 6. Release 6.1.3.1.3 SFP-100-BX20NU Not supported 6.R02 added support for the SFP-GIG-T at 10/100/1000 Mbits on OS6850-U24X noncombo ports only.3 SFP-100-LC-SM40 Not supported 6.3.SFP Compatibility Matrix OmniSwitch 6850 Series OmniSwitch 6850 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6850: SFP OS6850 Combo Ports OS6850-U24X (Excluding U24X) SFP-GIG-SX All 6.1.1 6.1 6.4.1.3 SFP-100-BXLC-D Not supported 6.1.3.3.3.2 1.3.1 6.3 SFP-GIG-LH40 All 6.3 Not Supported 6.1. 2.3 SFP-GIG-BX-D 6.3 SFP-GIG-LH70 All 6.2 SFP-100-LC-MM Not supported 6.1.1.3 SFP-GIG-LX All 6.3 SFP-GIG-CWD All 6. SFP-GIG-T is not supported on OS6850 combo ports.1.1.

4.4 SFP-100-LC-SM401 Not supported 6.4 6.4.4.4.4 SFP-GIG-BX-U 6.4 1 Not supported 6.4 Not Supported 6.4.4.4.4 6.4 SFP-10G-LR 6.4 SFP-GIG-CWD 6.4.4 6.4 6.4 6.4 SFP-GIG-LH70 6.OmniSwitch 6850E Series SFP Compatibility Matrix OmniSwitch 6850E Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6850E: SFP 6850E OS6850E-U24X (Excluding U24X) SFP-GIG-SX 6.4.4 SFP-100-LC-SM15 1.4 6.4 SFP-10G-LRM 6.4 SFP-GIG-T 1 SFP-DUAL-MM SFP-DUAL-SM10 Not Supported 6.4. * 10/100/1000 Mbps SFP transceivers are not supported on 10-Gigabit SFP+ ports.4 SFP-10G-SR 6.4.4.4.4 SFP-10G-C 6.4.4.4 SFP-10G-ER 6.4.4.4 6.4.4.4.4.4. Supported on OS6850E-U24X non-combo ports only.4.4 1 Not supported 6.4 6.4.4 6.4.4.4 SFP-GIG-BX-D 6.4 SFP-GIG-LH40 6.4 Not Supported 6.4.4 SFP-100-LC-MM1 SFP-100-BXLC-D SFP-100-BXLC-U Not supported 6.4 6.4.4 SFP-100-BX20NU1 Not supported 6.4.4.4 SFP-GIG-LX 6.4 SFP-GIG-EXTND 6.4 6.4 6.4.4. page 4-38 OmniSwitch Transceivers Guide April 2011 .4.4.4 1 Not supported 6.4.4 6.4.4 SFP-100-BX20LT 1 Not supported 6.

3.3 SFP-GIG-LH70 6.3.3 SFP-GIG-LX 6.3.3.SFP Compatibility Matrix OmniSwitch 6400 Series OmniSwitch 6400 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6400: SFP OS6400 (All ports/All models) SFP-GIG-SX 6.3 SFP-100-LC-SM40 6.4.3 SFP-100-LC-SM15 6.3 SFP-GIG-LH40 6. 2. SFP-GIG-T supports 10/100/1000 Mbits on non-combo ports only.3.2 6.3 1.3 SFP-GIG-BX-U 6.2 SFP-100-LC-MM 6.3.3.3.3 SFP-GIG-EXTND 6.3.4.3 SFP-100-BXLC-D 6.3.2 SFP-100-BXLC-U 6.3.3.3 SFP-GIG-BX-D 6.3 SFP-DUAL-MM Not supported SFP-DUAL-SM10 Not supported SFP-100-BX20LT 6. OmniSwitch Transceivers Guide April 2011 page 4-39 . SFP-GIG-T is not supported on OS6400 combo ports.3.3 SFP-100-BX20NU 6.3 SFP-GIG-CWD SFP-GIG-T Not supported 1.

6.1 SFP-DUAL-MM Not supported SFP-DUAL-SM10 Not supported 1 6.6.6.6.1 SFP-100-BX20NU1 6.1 SFP-GIG-BX-U 6.1 SFP-GIG-LX 6.1 SFP-100-LC-SM40 1 6. Not supported on non-combo ports.6.1 SFP-100-BXLC-U SFP-100-LC-SM15 1 6.6.6.6.1 SFP-GIG-CWD Not supported SFP-GIG-T 6.6.1 SFP-GIG-EXTND 6. page 4-40 OmniSwitch Transceivers Guide April 2011 .1 1.6.1 1 6.1 SFP-GIG-LH70 6.1 SFP-100-BX20LT 1 SFP-100-BXLC-D 6.1 SFP-GIG-BX-D 6.6.6.1 SFP-GIG-LH40 6.6.1 SFP-100-LC-MM1 6.6.6.OmniSwitch 6250 Series SFP Compatibility Matrix OmniSwitch 6250 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6250: SFP OS6250 SFP-GIG-SX 6.

SFP Compatibility Matrix OmniStack 6200 Series OmniStack 6200 Series The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniStack 6200: SFP OS6200 (All ports/All models) SFP-GIG-SX All SFP-GIG-LX All SFP-GIG-LH40 All SFP-GIG-LH70 All SFP-GIG-EXTND All SFP-GIG-CWD Not supported SFP-GIG-T All SFP-DUAL-MM Not supported SFP-DUAL-SM10 Not supported SFP-100-BX20LT All SFP-100-BX20NU All 1 SFP-100-BXLC-D All 1 All SFP-100-LC-MM1 All SFP-100-BXLC-U 1 All SFP-100-LC-SM401 All SFP-GIG-BX-D All SFP-GIG-BX-U All SFP-100-LC-SM15 OmniSwitch Transceivers Guide April 2011 page 4-41 .

3.4.1 XFP-10G-LR 6.1 XFP-10G-ZR80 6.R02 6.4 XFP-10G-DWDM OmniSwitch 9000E Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 9000E Series: XFP OS9-XNI-U2E XFP-10G-SR 6.3.4.1.1 XFP-10G-DWDM 6.4.1 XFP-10G-ER40 6.1 XFP-10G-CX4 6.3.4.1.4.1 page 5-42 OmniSwitch Transceivers Guide April 2011 .OmniSwitch 9000 Series 5 XFP Compatibility Matrix XFP Compatibility Matrix OmniSwitch 9000 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 9000 Series: XFP OS9-XNI-U2 OS9-XNI-U6 XFP-10G-SR All All XFP-10G-LR All All XFP-10G-ER40 All All XFP-10G-ZR80 All All XFP-10G-CX4 6.R02 6.4 6.3.4.

R02 XFP-10G-DWDM OmniSwitch Transceivers Guide 6.4 April 2011 page 5-43 .3.3. OmniSwitch 6855-U24X supports 10-Gigabit SFP+ Transceivers. OmniSwitch 6850 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6850: XFP All OmniSwitch 6850 10-Gigabit Models XFP-10G-SR All XFP-10G-LR All XFP-10G-ER40 All XFP-10G-ZR80 All XFP-10G-CX4 6.XFP Compatibility Matrix OmniSwitch 6855 Series OmniSwitch 6855 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6855: XFP OmniSwitch 6855 1 Not Supported All 1.1.

OmniSwitch 6850E Series XFP Compatibility Matrix OmniSwitch 6850E Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6850E: XFP OmniSwitch 6850E 1 Not Supported All 1. OmniSwitch 6850E only supports 10-Gigabit SFP+ Transceivers. OmniSwitch 6400 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6400: XFP All OmniSwitch 6400 No 10-Gig Support OmniSwitch 6250 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniSwitch 6250: XFP All OmniSwitch 6250 No 10-Gig Support OmniStack 6200 Series The following table shows the 10-Gigabit Ethernet transceiver configurations and supported releases on the OmniStack 6200: XFP All page 5-44 OmniStack 6200 No 10-Gig Support OmniSwitch Transceivers Guide April 2011 .