You are on page 1of 65

Cisco.Test-inside.200-101.v2014-02-10.by.Nada.

120q
Number: 200-101
Passing Score: 825
Time Limit: 120 min
File Version: 12.5

Exam Code: 200-101
Exam Name: Interconnecting Cisco Networking Devices Part 2
(ICND2)
Powered by NCV. VIÑA. CHILE.

Sections
1. LAN Switching Technologies
2. IP Routing Technologies
3. IP Services
4. Troubleshooting
5. WAN Technologies

Multiple Choice
QUESTION 1
Refer to the exhibit.
Why has this switch not been elected the root bridge for VLAN1?

A.
B.
C.
D.

It has more than one interface that is connected to the root network segment.
It is running RSTP while the elected root bridge is running 802.1d spanning tree.
It has a higher MAC address than the elected root bridge.
It has a higher bridge ID than the elected root bridge.

Correct Answer: D
Section: LAN Switching Technologies
QUESTION 2
Refer to the exhibit.
At the end of an RSTP election process, which access layer switch port will assume the discarding role?

A.
B.
C.
D.
E.
F.

Switch3, port fa0/1
Switch3, port fa0/12
Switch4, port fa0/11
Switch4, port fa0/2
Switch3, port Gi0/1
Switch3, port Gi0/2

Correct Answer: C
Section: LAN Switching Technologies
QUESTION 3
Refer to the exhibit.
Which switch provides the spanning-tree designated port role for the network segment that services the
printers?

B. D. RSTP defines new port roles.1D STP. D. This switch is running RSTP while the elected designated switch is running 802. what is the reasons that interface FastEthernet 0/10 is not the root port for VLAN 2? A. This switch has a lower bridge ID for VLAN 2 than the elected designated switch. C. RSTP is a proprietary implementation of IEEE 802.1D STP.A. B. Switch1 Switch2 Switch3 Switch4 Correct Answer: C Section: LAN Switching Technologies QUESTION 4 Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950.1d Spanning Tree. This switch interface has a higher path cost to the root bridge than another in the topology. Correct Answer: BE Section: LAN Switching Technologies QUESTION 6 Which port state is introduced by Rapid-PVST? A. RSTP defines no new port states. This switch has more than one interface connected to the root network segment in VLAN 2. D. RSTP cannot operate with PVST+. E. learning listening discarding forwarding Correct Answer: C Section: LAN Switching Technologies . B. RSTP is compatible with the original IEEE 802. C. C. B. C. D.) A. Correct Answer: C Section: LAN Switching Technologies QUESTION 5 Which two of these statements regarding RSTP are correct? (Choose two.

learning.) A. C. discarding. D. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three. root SwitchD. B. Each of these four switches has been configured with a hostname. designated SwitchC. Gi0/2. F. D. Fa0/2.) A. C.) A.QUESTION 7 Refer to the exhibit. root SwitchB. Gi0/2. Fa0/2. B. RSTP significantly reduces topology reconverging time after a link failure. No other configuration changes have been made. RSTP port states are blocking. root SwitchB. designated SwitchA. Gi0/1. C. or forwarding. E. E. discarding listening learning forwarding disabled Correct Answer: AD Section: LAN Switching Technologies QUESTION 9 Which three statements about RSTP are true? (Choose three. . Fa0/1. as well as being configured to run RSTP. B. SwitchA. root Correct Answer: ABF Section: LAN Switching Technologies QUESTION 8 Which two states are the port states when RSTP has converged? (Choose two. RSTP expands the STP port roles by adding the alternate and backup roles.

It uses cost to determine the best route. OSPF is a classful routing protocol. OSPF routers discover neighbors before exchanging routing information. EIGRP and OSPF are classful routing protocols and summarize routes by default. Automatic summarization at classful boundaries can cause problems on discontiguous subnets. RIPv1 and OSPF are classless routing protocols. B. C. Correct Answer: C Section: IP Routing Technologies QUESTION 14 . C. PVST+ supports Layer 3 load balancing without loops. RSTP uses the same timer-based process as STP on point-to-point links. to provide optimized bandwidth usage. Classful routing protocols send the subnet mask in routing updates. OSPF routers send the complete routing table to all directly attached routers. Correct Answer: ACF Section: IP Routing Technologies QUESTION 13 Which statement is true. B. D. It converges quickly. D. F. PVST+ allows the root switch location to be optimized per VLAN. PVST+ reduces the CPU cycles for all the switches in the network. It uses the DUAL algorithm to determine the best route. physical data link network transport Correct Answer: B Section: LAN Switching Technologies QUESTION 11 What is one benefit of PVST+? A. Correct Answer: ABD Section: LAN Switching Technologies QUESTION 10 At which layer of the OSI model is RSTP used to prevent loops? A. D. F. B. C. Correct Answer: C Section: LAN Switching Technologies QUESTION 12 What are three characteristics of the OSPF routing protocol? (Choose three. E. D.) A. RSTP also uses the STP proposal-agreement sequence. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does. E. B. PVST+ automatically selects the root bridge location. as relates to classful or classless routing? A. C.D.

0.14 B.0. The link to the ISP should NOT participate in OSPF and should only be advertised as the default route. B. Delay.0 0.2. B. D.0 10. Successor routes are stored in the neighbor table following the discovery process.0 0.0.0 10.2.0. Successor routes are saved in the topology table to be used if the primary route fails.16 0. C.255.255. C.0. Successor routes are flagged as 'active' in the routing table. D.0.0 10.0.10.2. Delay.0.0. and Load Correct Answer: A Section: IP Routing Technologies QUESTION 15 Which statements are true about EIGRP successor routes? (Choose two.14 D.13 0. Correct Answer: AD Section: IP Routing Technologies QUESTION 16 Refer to the exhibit.10. MTU.0. Core(config-router)# default-information originate Core(config-router)# network 10.) A. Reliability.0. Bandwidth Bandwidth and Delay Bandwidth.14 C.0.10.255 area 0 Core(config-router)# exit Core(config)# ip route 0.0 0.2.2. Core(config-router)# default-information originate .15 area 0 Core(config-router)# exit Core(config)# ip route 0.0. and MTU Bandwidth.0.0 0. A successor route may be backed up by a feasible successor route.Which parameter or parameters are used to calculate OSPF cost in Cisco routers? A.242 area 0 Core(config-router)# exit Core(config)# ip route 0. Core(config-router)# default-information originate Core(config-router)# network 10.0.0. The network associate is configuring OSPF on the Core router.10.10.0. What set of commands will properly configure the Core router? A. A successor route is used by EIGRP to forward traffic to a destination. All the connections to the branches should be participating in OSPF. Core(config-router)# default-information originate Core(config-router)# network 10. E.0.

It decreases the metric for routes that are advertised from RouterB.0.0. E.0.14 Correct Answer: C Section: IP Routing Technologies QUESTION 17 Refer to the exhibit.0 0. It specifies that the router ID for RouterB should be 10.2. Correct Answer: BC Section: LAN Switching Technologies QUESTION 18 What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router? A.0.0 10.10. Which two statements are true about the loopback address that is configured on RouterB? (Choose two. It indicates that RouterB should be elected the DR for the LAN. D. It ensures that data will be forwarded by RouterB. 2 4 16 unlimited Correct Answer: B Section: IP Routing Technologies QUESTION 19 Which parameter would you tune to affect the selection of a static route as a backup.2. B. It provides stability for the OSPF process on RouterB. hop count .1.) A.Core(config-router)# network 10.0. D. C. C.0.31 area 0 Core(config-router)# exit Core(config)# ip route 0. when a dynamic protocol is also being used? A.10. B.32 0.0.0.

Configuration complexity decreases as network size increases. D.B. B. and EIGRP. B. the sequencing and acknowledgment of link-state packets the requirement for a hierarchical IP addressing scheme for optimal functionality the high volume of link-state advertisements in a converged network the high demand on router resources to run the link-state routing algorithm the large size of the topology table listing all advertised routes in the converged network Correct Answer: BD Section: IP Routing Technologies QUESTION 21 Which two are advantages of static routing when compared to dynamic routing? (Choose two. G. Correct Answer: BG Section: IP Routing Technologies QUESTION 22 Which command enables IPv6 forwarding on a Cisco router? A. E. Routing tables adapt automatically to topology changes. Route summarization is computed automatically by the router. C. Routing traffic load is reduced when used in stub network links. E. Security increases because only the network administrator may change the routing table.) A. C. the route learned through EIGRP B. Routing updates are automatically sent to neighbors. Each process learns a route to the same remote network. D.) A. An efficient algorithm is used to build routing tables. B. each configured with default characteristics. C. the route learned through RIP . If there are no static routes to the destination and none of the routes were redistributed. using automatic updates. the route learned through OSPF C. C. OSPF. D. which route will be placed in the IP routing table? A. E. ipv6 local ipv6 host ipv6 unicast-routing ipv6 neighbor Correct Answer: C Section: IP Services QUESTION 23 A router is running three routing processes: RIP. administrative distance link bandwidth link delay link cost Correct Answer: B Section: IP Routing Technologies QUESTION 20 What are two drawbacks of implementing a link-state routing protocol? (Choose two. F. D.

Which routers are likely to have been elected as DR? (Choose two. 10. what router ID will OSPF use for this router? A.16.) A. D.168.154. the route with the lowest metric E.5. Given the output for this command. C.1. As part of examining the router resources.1 172.2 10. All the router OSPF priorities are at the default and the router IDs are shown with each router. There is concern that a lack of router resources is impeding internetwork performance. if the router ID has not been manually set.154. C.3 Correct Answer: C Section: IP Routing Technologies QUESTION 25 The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. Corp-1 Corp-2 Corp-3 Corp-4 . all three routes with the router load balancing Correct Answer: A Section: IP Routing Technologies QUESTION 24 Refer to the exhibit. the OSPF DRs need to be known.1.1 192.5. B. B. D.D.

Branch-1 F. It sends a multicast query packet to all adjacent neighbors requesting available routing paths to the destination network. It sends a copy of its neighbor table to all adjacent routers. C. D. D. C. B. show ip ospf link-state show ip ospf lsa database show ip ospf neighbors show ip ospf database Correct Answer: D Section: IP Routing Technologies QUESTION 28 What is the default administrative distance of OSPF? A.E. C.1111 switchport port-security maximum 2 switchport port-security What is the result of the above configuration being applied to the switch? A. B. 90 100 110 120 Correct Answer: C Section: IP Routing Technologies QUESTION 29 The following configuration is applied to a Layer 2 Switch (Choose two). Correct Answer: C Section: IP Routing Technologies QUESTION 27 Which command is used to display the collection of OSPF link states? A. It routes all traffic that is addressed to the destination network to the interface indicated in the routing table.1111. B. Branch-2 Correct Answer: DF Section: IP Routing Technologies QUESTION 26 What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is in active status? A. A host with a mac address of 0000.1111 and up to two other hosts can connect to FastEthernet 0/4 simultaneously .1111. It broadcasts Hello packets to all routers in the network to re-establish neighbor adjacencies. D. interface fastethernet 0/4 switchport mode access switchport port-security switchport port-security mac-address 0000.

but the technician is able to ping the S0/0 interface of R2 from Host1. SNMP or syslog messages Correct Answer: D Section: IP Services QUESTION 31 A technician pastes the configurations in the exhibit into the two new routers shown. C. The configurations of the hosts have been verified as correct. A ping from Host1 to Host2 fails. The switch can send an SNMP message to the network management station E. SNMP or syslog messages port disabled.1111 and one other host can connect to Fast Ethernet 0/4 simultaneously C. no SNMP or syslog messages port disabled. What is the cause of the problem? . unknown packets dropped. A host with a mac address of 0000.1111. port enabled. unknown packets dropped. Otherwise. the routers are configured with their default configurations. no SNMP or syslog messages port enabled. Violating addresses are dropped and no record of the violation is kept D. Which of these correctly describes the results of port security violation of an unknown packet? A. B. D. The port is effectively shutdown Correct Answer: BD Section: IP Services QUESTION 30 Refer to the exhibit.B.

A. What three actions will the switch take when a frame with an unknown source MAC address arrives at the interface? (Select three. C. The interfaces on R2 are not configured properly. Send an SNMP trap. C. Correct Answer: C Section: IP Routing Technologies QUESTION 32 Refer to the exhibit. D. Correct Answer: ABC Section: IP Services QUESTION 33 What does the frame-relay interface-dlci command configure? A. B. The IP addressing scheme has overlapping subnetworks. local DLCI on the subinterface remote DLCI on the main interface remote DCLI on the subinterface local DLCI on the main interface Correct Answer: A Section: WAN Technologies . E. D. Write the MAC address to the startup-config. D. R1 has no route to the 192. B. B. E.168.1. Shut down the port. C.) A.128 network. Forward the traffic. The ip subnet-zero command must be configured on both routers. The serial cable on R1 needs to be replaced. F. Send a syslog message. Increment the Security Violation counter.

B.10. The router will forward packets from R3 to R1. Correct Answer: DE Section: (none) QUESTION 35 Refer to the exhibit. The router will forward packets from R3 to R1 to R2. Based on the exhibited routing table. C.192/26 LAN be forwarded to 192.) A.1? A. D.QUESTION 34 What can be done to secure the virtual terminal interfaces on a router? (Choose two. Administratively shut down the interface.10. D. B. The router will forward packets from R3 to R2 to R1. Configure a virtual terminal password and login process. C. Physically secure the interface. The router will forward packets from R3 to R2 to R1 AND from R3 to R1.168. E.168. how will packets from a host within the 192. Create an access list and apply it to the virtual terminal interfaces with the access-group command. Correct Answer: C Section: (none) QUESTION 36 Refer to the exhibit. What information about the interfaces on the Main_Campus router is true? . Enter an access list and apply it to the virtual terminal interfaces using the access-class command.

These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172. Correct Answer: B Section: LAN Switching Technologies QUESTION 37 Refer to the exhibit.3. B. What is true about this configuration? A. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172. The LAN interfaces are configured on different subnets.0 B. D. The hosts in the VLANs have been configured with the appropriate default gateway.A.0.19.19.255 area 0 C.0 . These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172. C-router is to be used as a "router-on-a-stick" to route between the VLANs.19. Interface FastEthernet 0/0 is configured as a trunk.0. All the interfaces have been properly configured and IP routing is operational. C.0. E. Interface FastEthernet 0/0 is administratively deactivated.0 0.0. The Layer 2 protocol of interface Serial 0/1 is NOT operational. The router is a modular router with five FastEthernet interfaces.

Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. In addition. No further routing configuration is required. Correct Answer: E Section: IP Routing Technologies QUESTION 39 Refer to the exhibit.100.16. Any packet destined for a network that is not directly connected to router R1 will be dropped. B. How will the default route configured on R1 affect the operation of R2? A. Assume that all of the router interfaces are operational and configured correctly.100. E. and 172. R1 will then send that packet back to R2 and a routing loop will occur. assume that OSPF has been correctly configured on router R2. Correct Answer: D Section: LAN Switching Technologies QUESTION 38 Refer to the exhibit. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.D. C. Assume that all router interfaces are operational and correctly configured.128.16. The networks directly connected to router R2 will not be able to communicate with the 172.0. How will router R2 be affected by the configuration of R1 that is shown in the exhibit? .16. 172.100.64 subnetworks. D.

0/24 will remain in the RTA routing table.14. RTA is configured with a basic configuration. D. The link between the two routers is operational and no routing protocols are configured on either router. B. Router R2 will not form a neighbor relationship with R1. The line shown in the exhibit is then added to router RTA .16. Correct Answer: A Section: IP Routing Technologies QUESTION 40 Refer to the exhibit.14. C. Router R2 will obtain a full routing table. C. what effect will the shutdown have on router RTA? A. A packet to host 172. Based on the output displayed . R2 will obtain OSPF updates from R1. but will not obtain a default route from R1. from R1. but all other directly connected networks will be present. Correct Answer: A Section: IP Routing Technologies QUESTION 41 Refer to the exhibit. D. The show interfaces serial 0/1 command was issued on the R10-1 router.16. Should interface Fa0/0 on router RTB shut down. RTA will remove the route.225 will be dropped by router RTA Router RTA will send an ICMP packet to attempt to verify the route. A route to 172. including a default route. Because router RTB will send a poison reverse packet to router RTA.A. as well as the two Ethernet networks connected to R1. R2 will not have a route for the directly connected serial network. B.

What does this mean? . Each VLAN uses a separate address space. E.which statement is correct? A. The cable connected to the serial 0/1 interface of the R10-1 router is a DTE cable. Correct Answer: E Section: WAN Technologies QUESTION 42 Which three statements are typical characteristics of VLAN arrangements? (Choose three. The R10-1 router can ping the router interface connected to the serial 0/1 interface. B. A switch maintains a separate bridging table for each VLAN. Correct Answer: BDE Section: LAN Switching Technologies QUESTION 43 The output of the show frame-relay pvc command shows "PVC STATUS = INACTIVE". D.) A. VLANs cannot span multiple switches. VLANs typically decrease the number of collision domains. The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is using the default serial interface encapsulation. B. C. The CSU used with the serial 0/1 interface of the R10-1 router has lost connection to the service provider. D. C.544. F. Connectivity between VLANs requires a Layer 3 device. E. The clock rate used for interface serial 0/1 of the R10-1 router is 1. A new switch has no VLANs configured.000 bits per second.

B. Based on the output from RouterA. The cable that is connected to S0/0 on RouterA is faulty.0. D. The PVC is configured correctly. Correct Answer: D Section: WAN Technologies QUESTION 44 Refer to the exhibit. F. is operating normally. Interface S0/0 on RouterA is configured with an incorrect subnet mask. The PVC is configured correctly. Interface S0/0 on RouterB is administratively down. B.168.) . The PVC is configured correctly on the local switch. E.) A.3. C.A.0 are unable to reach hosts in network 192. The output that is shown is generated at a switch. but there is a problem on the remote end of the PVC E. and is no longer actively seeking the address of the remote router. is operating normally. Hosts in network 192.2. The PVC is not configured on the local switch. The PVC is configured correctly and is operating normally. what are two possible reasons for the failure? (Choose two. but no data packets have been detected for more than five minutes. Which three statements are true? (Choose three. D. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA Correct Answer: EF Section: IP Routing Technologies QUESTION 45 Refer to the exhibit. and is waiting for interesting traffic to trigger a call to the remote router. C.168. The IP address that is configured on S0/0 of RouterB is not in the correct subnet. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.

A. D. This switch must be the root bridge for all VLANs on this switch. Thirty VLANs have been configured on this switch. All designated ports are in a forwarding state. or forwarding. C. E. B. All ports will be in a state of discarding. what is required for RouterA to exchange routing updates with RouterC? A. D. All interfaces that are shown are on shared media. learning. The bridge priority is lower than the default value for spanning tree. F. When running EIGRP. Correct Answer: ACE Section: LAN Switching Technologies QUESTION 46 Refer to the exhibit. B. AS numbers must be changed to match on all the routers Loopback interfaces must be configured so a DR is elected The no auto-summary command is needed on Router A and Router C Router B needs to have two network statements. C. one for each connected network Correct Answer: A Section: IP Routing Technologies .

Correct Answer: D Section: LAN Switching Technologies QUESTION 49 Refer to the exhibit. B. B.) . Only the hosts in VLAN 1 on the two switches will be able to communicate with each other. A technician has configured the FastEthernet 0/1 interface on Sw11 as an access link in VLAN 1. C. The hosts in all VLANs on the two switches will be able to communicate with each other. C.QUESTION 47 Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state? A. converged redundant provisioned spanned Correct Answer: A Section: LAN Switching Technologies QUESTION 48 Refer to the exhibit. D. Only the hosts in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other. what will be the result of making this change on Sw11? A. Based on the output from the show vlan brief command issued on Sw12. What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two. D. Hosts will not be able to communicate between the two switches.

168. Router(config)# router eigrp 100 Router(config-router)# network 192.255.20.0 Router(config-if)# no shut down B.1.1 Correct Answer: BE Section: LAN Switching Technologies QUESTION 50 What command is used to verify the DLCI destination address in a Frame Relay static configuration? A. Router(config)# interface fastethernet 0/0 Router(config-if)# ip address 192.0 D. C.1 255.10. show frame-relay pvc show frame-relay lmi show frame-relay map show frame relay end-to-end Correct Answer: C Section: WAN Technologies QUESTION 51 .168.168.2 Router(config-subif)# encapsulation dot1q 20 Router(config-subif)# ip address 192.255.1 255.0 C.1 255.20.168.1 Router(config-subif)# encapsulation dot1q 10 Router(config-subif)# ip address 192.1. Switch1(config)# interface fastethernet 0/1 Switch1(config-if)# switchport mode trunk F. D.168.168.A.255.255.0 Router(config-router)# network 192. B.255.255.10. Switch1(config)# vlan database Switch1(config-vlan)# vtp domain XYZ Switch1(config-vlan)# vtp server E. Switch1(config)# interface vlan 1 Switch1(config-if)# ip default-gateway 192.0 Router(config)# interface fastethernet 0/0. Router(config)# interface fastethernet 0/0 Router(config-if)# no shut down Router(config)# interface fastethernet 0/0.

The router will return the packet to its source. The router will forward the packet via Serial2. The router will forward the packet via either Serial0 or Serial1. How will the router handle a packet destined for 192.156? A. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two. Correct Answer: C Section: IP Routing Technologies QUESTION 52 Refer to the exhibit.0. B.Refer to the exhibit.) . D. The router will drop the packet.2. C.

Router1 will not play a role in communications between host A and host D. E. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces. It avoids split-horizon issues with distance vector routing protocols. Correct Answer: B Section: WAN Technologies QUESTION 54 Which two statistics appear in show frame-relay map output? (Choose two. the number of BECN packets that are received by the router the value of the local DLCI the number of FECN packets that are received by the router the status of the PVC that is configured on the router the IP address of the local router Correct Answer: BD Section: WAN Technologies QUESTION 55 Which protocol is an open standard protocol framework that is commonly used in VPNs.) A. D. Layer 2 B. C. D. B. Correct Answer: DF Section: LAN Switching Technologies QUESTION 53 What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology? A. E. to provide secure end-to-end communications? A. B.A. F. A multipoint interface offers greater security compared to point-to-point subinterface configurations. C. B. Layer 3 . B. Host E and host F use the same IP gateway address. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type. D. D. C. The multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point-to-point configurations. IP addresses can be conserved if VLSM is not being used for subnetting. RSA L2TP IPsec PPTP Correct Answer: C Section: WAN Technologies QUESTION 56 At which layer of the OSI model does PPP perform? A. Router1 and Switch2 should be connected via a crossover cable. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit. C.

B. on a serial interface? A.151.168.C. active Which statements represent what is shown? (Choose three. Develop multipoint subinterfaces.168. status defined. Layer 5 Correct Answer: A Section: WAN Technologies QUESTION 57 The command show frame-relay map gives the following output: Serial 0 (up): ip 192. 192.168.4 dlci 122. Remove the broadcast keyword from the frame-relay map command. B. Create a full-mesh topology. E. B. Disable Inverse ARP. Router(config-if)# ppp authentication chap fallback ppp . C. D. broadcast.) A.151. Correct Answer: BD Section: WAN Technologies QUESTION 59 What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three. Layer 4 D. C.) A.4 represents the IP address of the remote router 192. dynamic. E.) A. E. Configure point-to-point subinterfaces. F.151.4 represents the IP address of the local serial interface DLCI 122 represents the interface of the remote serial interface DLCI 122 represents the local number used to connect to the remote address broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC active indicates that the ARP process is working Correct Answer: ADE Section: WAN Technologies QUESTION 58 What can be done to Frame Relay to resolve split-horizon issues? (Choose two. D. with PAP as the fallback method. D. reduced cost better throughput broadband incompatibility increased security scalability reduced latency Correct Answer: ADE Section: WAN Technologies QUESTION 60 Which command is used to enable CHAP authentication. C. F.

255. B. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.255.16.168.255. C.1. HDLC PPP X. Router(config-if)# authentication ppp chap fallback ppp D.252 Main(config-if)# no shut B.255. D.2 202 broadcast command? A.1. defines the destination IP address that is used in all broadcast packets on DCLI 202 defines the source IP address that is used in all broadcast packets on DCLI 202 defines the DLCI on which packets from the 192.1 255.16.B.168.2 IP address Correct Answer: D Section: WAN Technologies QUESTION 62 Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has builtin security mechanisms? A. C.1 255.252 Main(config-if)# encapsulation ppp Main(config-if)# no shut C.255.255.16. B.252 .25 Frame Relay Correct Answer: B Section: WAN Technologies QUESTION 63 Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers? A.1.168.1 255.1. D. Router(config-if)# ppp authentication chap pap C.2 IP address are received defines the DLCI that is used for all packets that are sent to the 192. Main(config)# interface serial 0/0 Main(config-if)# ip address 172. Router(config-if)# authentication ppp chap pap Correct Answer: B Section: WAN Technologies QUESTION 61 What is the result of issuing the frame-relay map ip 192. The router at the remote office is a non-Cisco router.1. C. How should the network administrator configure the serial interface of the main office router to make the connection? A. B. IETF ANSI Annex D Q9333-A Annex A HDLC Correct Answer: A Section: WAN Technologies QUESTION 64 A network administrator needs to configure a serial link between the main office and a remote location. Main(config)# interface serial 0/0 Main(config-if)# ip address 172. D.1.

252 Main(config-if)#encapsulation ietf Main(config-if)# no shut Correct Answer: B Section: WAN Technologies QUESTION 65 Which PPP subprotocol negotiates authentication options? A. One interface has a problem. The operational status of the interfaces cannot be determined from the output shown. D. B. C.255. All OSPF routers in an area must have the same process ID.16. E. what is the operational status of the interfaces of R2 as indicated by the command output shown? A.255. B. Main(config)# interface serial 0/0 Main(config-if)#ip address 172. NCP ISDN SLIP LCP DLCI Correct Answer: D Section: WAN Technologies QUESTION 66 Refer to the exhibit. Assuming that the entire network topology is shown. D.) Router(config)# router ospf 1 A. Two interfaces have problems.1. The interfaces are functioning correctly.1 255. C.Main(config-if)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut D. Correct Answer: C Section: IP Routing Technologies QUESTION 67 Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two. .

E.535. B. Correct Answer: CD Section: IP Routing Technologies QUESTION 68 Refer to the exhibit. Hello packets are sent to each neighbor to determine the processor identifier. which router is the feasible successor? A. Given the output from the show ip eigrp topology command. Different process identifiers can be used to run multiple OSPF processes The process number can be any number from 1 to 65. C. D.B. C. . Only one process number can be used on the same router.

D. 802.1Q trunking are correct? (Choose three. B. C.1Q trunking ports can also be secure ports.1Q native VLAN frames are untagged by default. D. 802.) A.) A. point-to-point connectivity. B. Which WAN protocol is being used? .D.1Q trunks can use 10 Mb/s Ethernet interfaces. C.1Q trunks require full-duplex. Correct Answer: B Section: IP Routing Technologies QUESTION 69 Which three of these statements regarding 802. E. 802.1Q trunks should have native VLANs that are the same at both ends. 802. PPP WAP DSL L2TPv3 Ethernet Correct Answer: AC Section: WAN Technologies QUESTION 71 Refer to the exhibit. 802. Correct Answer: ACE Section: LAN Switching Technologies QUESTION 70 Which two options are valid WAN connectivity methods? (Choose two. E.

ATM HDLC Frame Relay PPP Correct Answer: C Section: WAN Technologies QUESTION 72 What occurs on a Frame Relay network when the CIR is exceeded? A. D. They are ideal for full-mesh topologies.) A. . B. They require the use of NBMA options when using OSPF. E. CHAP authentication is performed only upon link establishment. CHAP authentication passwords are sent in plaintext. They require a unique subnet within a routing domain. Correct Answer: BC Section: WAN Technologies QUESTION 74 Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two. All TCP traffic is marked discard eligible and a BECN is sent. They create split-horizon issues. C. They emulate leased lines. B. D. B.) A. D. All TCP traffic is marked discard eligible. C. CHAP uses a three-way handshake. CHAP authentication periodically occurs after link establishment. All traffic exceeding the CIR is marked discard eligible. Correct Answer: D Section: WAN Technologies QUESTION 73 What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two. C. C. B. E. All UDP traffic is marked discard eligible and a BECN is sent. D. CHAP uses a two-way handshake.A.

F.64 0. C. C. B.63 area 0 After completing the configuration.0.) A. FastEthernet0 /1 .F. show frame-relay lmi show frame-relay map show frame-relay pvc show interfaces serial Correct Answer: B Section: WAN Technologies QUESTION 76 What is the purpose of Inverse ARP? A. B.168. D. Correct Answer: BC Section: WAN Technologies QUESTION 75 Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link? A. D. the associate discovers that not all the interfaces are participating in OSPF. E. A network associate has configured OSPF with the command: City(config-router)# network 192.12. CHAP has no protection from playback attacks. to map a known IP address to a MAC address to map a known DLCI to a MAC address to map a known MAC address to an IP address to map a known DLCI to an IP address to map a known IP address to a SPID to map a known SPID to a MAC address Correct Answer: D Section: WAN Technologies QUESTION 77 Refer to the exhibit.0. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three. FastEthernet0 /0 B.

1 subnets D 10.0.0 [90/20514560] via 10. 10.4. 6w0d.0/22 is subnetted.0.0 [90/20514560] via 10. Serial0/1 E.2.0. Serial0/0 Serial0/1.0.0. 10.4.) .0/28 is subnetted.C. 1 subnets D 10.0 [90/20514560] via 10.2.2.4.2.0.0. 6w0d.0/28 is subnetted.0/30 is subnetted.0. 1 subnets D 10.104 Correct Answer: BCD Section: IP Routing Technologies QUESTION 78 Refer to the exhibit.0.2. The Lakeside Company has the internetwork in the exhibit.0.2.0.2.0.0 [90/20514560] via 10. Serial0/1 D.0. 6w0d. 1 subnets D 10. E.2. 10.2.4. Serial0/1 F. Serial0/1 C. D. F. 1 subnets D 10.102 Serial0/1.2.0.0 [90/20514560] via 10.0.0. 10.2.4 [90/20514560] via 10.0. 6w0d.2. 6w0d. The administrator would like to reduce the size of the routing table on the Central router.2. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets? A. 10.0.0.0.0/22 is subnetted.4. 10.0. 1 subnets D 10. Serial0/1 B.0/30 is subnetted.103 Serial0/1.2.0. 6w0d.2. Serial0/1 Correct Answer: D Section: IP Routing Technologies QUESTION 79 What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.

16.255 area 0 Router(config-router)# network 192. B. F. B. C. stored in the routing table a backup route.255 0 Router(config-router)# network 192. a backup route.255. B. hello packets SAP messages sent by other routers LSAs from other routers beacons received on point-to-point links routing tables received from other link-state routers TTL packets from designated routers Correct Answer: AC Section: IP Routing Technologies QUESTION 80 Which commands are required to properly configure a router to run OSPF and to add network 192. Router(config)# router ospf 0 Router(config)# router ospf 1 Router(config)# router ospf area 0 Router(config-router)# network 192. F.0 0. C.168. Not all the descriptions are used. stored in the topology table a primary route. C.0 0.0.0 255. E.A. stored in the topology table Correct Answer: C Section: IP Routing Technologies QUESTION 82 Drag and Drop Question Drag each description on the left to the appropriate term on the right.0.168. D.0 area 0 Correct Answer: BE Section: IP Routing Technologies QUESTION 81 Which type of EIGRP route entry describes a feasible successor? A.0.16.0.16.168.255.) A. E. Select and Place: . D.168. stored in the routing table a primary route. D.16.0/24 to OSPF area 0? (Choose two.

Correct Answer: Section: (none) QUESTION 83 Drag and Drop Question Drag the term on the left to its definition on the right (Not all options are used.) Select and Place: .

Correct Answer: Section: (none) QUESTION 84 Drag and Drop Question Drag the description on the left to the routing protocol on the right. (Not all options are used.) .

(Not all acronyms are used) Select and Place: .Select and Place: Correct Answer: Section: IP Routing Technologies QUESTION 85 Drag and Drop Question Drag the Frame Relay acronym on the left to match its definition on the right.

Correct Answer: Section: WAN Technologies QUESTION 86 Hotspot Question .

2 3 4 5 6 7 Correct Answer: C Section: IP Routing Technologies . D. B. With all routers and interfaces operational. C.OSPF is configured using default classful addressing. how many networks will be in the routing table of R1 that are indicated to be learned by OSPF? A. E. F.

what type of messaging. D. The routing table from each router is sent every 60 seconds. Correct Answer: B Section: IP Routing Technologies .QUESTION 87 Hotspot Question After the network has converged. occurs between R3 and R4? A. No messages are exchanged. The full database from each router is sent every 30 seconds. B. Hellos are sent every 10 seconds. C. if any.

16. D. E.QUESTION 88 Hotspot Question To allow or prevent load balancing to network 172.0/24.) A. which of the following commands could be used in R2? (Choose two.3. C. B. R2(config-if)#clock rate R2(config-if)#bandwidth R2(config-if)#ip ospf cost R2(config-if)#ip ospf priority R2(config-router)#distance ospf Correct Answer: BC .

C.2.16.1.1 172.1 172. B.2. From the following list of IP addresses configured on R1. D. which address will the OSPF process select as the router ID? A.16.Section: IP Routing Technologies QUESTION 89 Hotspot Question R1 is configured with the default configuration of OSPF.16.225 .1 172. 192.0.168.

Correct Answer: A Section: IP Routing Technologies QUESTION 90 Hotspot Question .

.

D. B. E. what password should be configured on the SouthIslands router in the branch office to allow a connection to be established with the Dubai router? A. Enable Secret Telnet Console Correct Answer: A Section: WAN Technologies QUESTION 91 Hotspot Question . No password is required. C.If required.

.

.

C.4. D. B. 825 230 694 387 Correct Answer: C Section: WAN Technologies QUESTION 92 Hotspot Question .What would be the destination Layer 2 address in the frame header for a frame that is being forwarded by Dubai to the host address of 172.4? A.30.

.

.

Which connection uses the default encapsulation for serial interfaces on Cisco routers?

A.
B.
C.
D.

The serial connection to the NorthCoast branch office.
The serial connection to the North branch office.
The serial connection to the Southlands branch office.
The serial connection to the Multinational Core.

Correct Answer: B
Section: WAN Technologies
QUESTION 93
Hotspot Question

0. B. Which command should be used to create this map? A.3 230 broadcast frame-relay map ip 172.3 694 broadcast frame-relay map ip 172. D.3 387 broadcast Correct Answer: B Section: WAN Technologies QUESTION 94 What are the benefit of using Netflow? (Choose three. Application & User Monitoring B.30. Network.A static map to the S-AMER location is required. frame-relay map ip 172.30.30.0. Network Planning C. C. Security Analysis .3 825 broadcast frame-relay map ip 172.0.30.0.) A.

E. Correct Answer: C Section: WAN Technologies QUESTION 97 Users have been complaining that their Frame Relay connection to the corporate site is very slow. D. GLBP supports up to eight virtual forwarders per GLBP group. Which statement describes DLCI 17? A. GLBP supports clear text and MD5 password authentication between GLBP group members. DLCI 17 describes a PVC on R2. C. GLBP supports up to 1024 virtual routers. F. The network administrator suspects that the link is overloaded. B.) A. B. Correct Answer: BDE Section: IP Services QUESTION 96 Refer to the exhibit. GLBP is an open source standardized protocol that can be used with multiple vendors. C. It cannot be used on R3 or R1. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider. GLBP can load share traffic across a maximum of four routers. Accounting/Billing Correct Answer: ACD Section: IP Services QUESTION 95 What are three benefits of GLBP? (Choose three. GLBP elects two AVGs and two standby AVGs for redundancy. DLCI 17 describes the ISDN circuit between R2 and R3. which output value indicates to the local router that traffic sent to the corporate site is experiencing congestion? . DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.D. Based on the partial output of the Router#show frame relay pvc command shown in the graphic. D.

8 is the local router port used to forward data. 102 is the remote DLCI that will receive the information. Which of the following statements is true concerning this command? A. D. E.16. D. E. The broadcast option allows packets. DLCI=100 last time PVC status changed 00:25:40 in BECN packets 192 in FECN packets 147 in DF packets 0 Correct Answer: C Section: WAN Technologies QUESTION 98 Refer to the exhibit. E. This command should be executed from the global configuration mode.3.16. What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown? A.1 was learned through Inverse ARP Correct Answer: E Section: WAN Technologies QUESTION 99 The command frame-relay map ip 10.16. .121. C. B. to be forwarded across the PVC.8 102 broadcast was entered on the router.16.3. C.1 from a DHCP server The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud The mapping between DLCI 100 and the end station IP address 172. This command is required for all Frame Relay configurations. The Serial0/0 interface is passing traffic.121. C. B. The IP address 10. D. such as RIP updates. The DLCI 100 was dynamically allocated by the router The Serial0/0 interface acquired the IP address of 172. B.A.

C.1/24 DLCI 28 192.10. E. F.1/24 DLCI 17 192. configure static frame relay map entries for each subinterface network.1/24 DLCI 99 192.Correct Answer: E Section: WAN Technologies QUESTION 100 In the Frame Relay network.12. D.168.168. which IP addresses would be assigned to the interfaces with point-to-point PVCs? A.3/24 DLCI 28 192.10.3/24 B.1/24 C.168.168.2/24 D.10.10.168.2/24 DLCI 28 192.10.168.2/24 DLCI 28 192. The retransmit interval and the .10.168.168.11.1 /24 DLCI 17 192. DLCI 16 192. DLCI 16 192.11.168.168.10. DLCI 16 192. remove the ip address from the physical interface create the virtual interfaces with the interface command configure each subinterface with its own IP address disable split horizon to prevent routing loops between the subinterface networks encapsulate the physical interface with multipoint PPP Correct Answer: BCD Section: WAN Technologies QUESTION 102 A network administrator is troubleshooting an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. DLCI 16 192.11.1/24 DLCI 99 192.10.10. Which of the following are required to solve this? (Choose three) A.4/24 Correct Answer: C Section: WAN Technologies QUESTION 101 It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit.10.13.1/24 DLCI 17 192.168.168.1/24 DLCI 99 192.168.2/24 DLCI 99 192. B.168.10.168.168.1/24 DLCI 17 192.

64/26 [90/2195456] via 192.168. D.20.168. Router# show ip eigrp adjacency Router# show ip eigrp topology Router#show ip eigrp interfaces Router#show ip eigrp neighbors Correct Answer: D Section: IP Routing Technologies QUESTION 103 Refer to the exhibit.5. D.20.192/26 network to a host on the LAN attached to router R1? R3# show ip route Gateway of last resort is not set 192 168.128/26 [90/2195456] via 192.0/24 is variably subnetted.168.20. Serial0/0 C 192.8/30 is directly connected. Serial0/0 D 192.queue counts for the adjacent routers also need to be checked. C. What path will packets take from a host on 192. 00:03:31.00:03:31.20. The company uses EIGRP as the routing protocol. FastEthernet0/0 D 192. Serial0/1 C 192.168. Serial0/1 A.192/26 is directly connected.0/30 [90/2681856] via 192. B.168. C. 00:03:31.168.0/24 from multiple sources.168.20.168.20.20. B.10.20.4/30 is directly connected.168. 2 masks D 192.20. 6 subnets.168.20.10.9.9. What command will display the required information? A.168. The path of the packets will be R3 to R2 to R1 The path of the packets will be R3 to R1 to R2 The path of the packets will be both R3 to R2 to R1 and R3 to R1 The path of the packets will be R3 to R1 Correct Answer: D Section: IP Routing Technologies QUESTION 104 A router receives information about network 192. Serial0/0 C 192. What will the router consider the most reliable information about the path to that network? .

A. 253 252 255 254 Correct Answer: A Section: (none) QUESTION 106 Which feature does PPP use to encapsulate multiple protocols? A.0. C.0/24 a static route to network 192.254/24 a default route with a next hop address of 192. an OSPF update for network 192.10. Host A pings interface S0/0 on router 3.168.168. B.168. C.10.10. NCP LCP IPCP IPXP Correct Answer: A Section: WAN Technologies QUESTION 107 What is the purpose of LCP? .168. B.0/16 a static route to network 192. B. what is the TTL value for that ping? A. E.0/24 a directly connected interface with an address of 192. F. C.168.168.1 Correct Answer: E Section: (none) QUESTION 105 Refer to the exhibit. D. D.10.0/24 with a local serial interface configured as the next hop a RIP update for network 192. D.10.

to perform authentication to negotiate control options to encapsulate multiple protocols to specify asynchronous versus synchronous Correct Answer: B Section: WAN Technologies QUESTION 108 Refer to the exhibit.A.4 arrives at the AcmeB router.2. From R1.1. unable to ping any of the subnets attached to RouterB.168.1. What action does the router take? A. what could be the problem? . C. C. B. forwards the received packet out the Serial0/0 interface forwards a packet containing an EIGRP advertisement out the Serial0/1 interface forwards a packet containing an ICMP message out the FastEthemet0/0 interface forwards a packet containing an ARP request out the FastEthemet0/1 interface Correct Answer: C Section: (none) QUESTION 109 Refer to the exhibit. D. A packet with a source IP address of 192. a network administrator is able to ping the serial interface of R2 but.4 and a destination IP address of 10. Based on the partial outputs in the exhibit. B. D.

E. C. EIGRP has been configured with an invalid autonomous system number. The EIGRP network statements are incorrectly configured. The IP addressing on the serial interface of RouterA is incorrect. B. Correct Answer: D Section: (none) .A. EIGRP does not support VLSM. The routing protocol has summarized on the classful boundary. D.

C. The local VLAN configuration is updated only when an update that has a higher configuration revision number is received. B. D. C. Correct Answer: CF Section: (none) QUESTION 112 Which protocol provides a method of sharing VLAN configuration information between two Cisco switches? A. Correct Answer: BC Section: (none) QUESTION 111 What are two characteristics of a switch that is configured as a VTP client? (Choose two. they send a VTP advertisement request to the VTP servers. When dynamic MAC address learning is enabled on an interface. E. If a switch that is configured to operate in client mode cannot access a VTP server.) A.1Q RSTP Correct Answer: B Section: (none) QUESTION 113 The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two. then the switch reverts to transparent mode. D.QUESTION 110 A network administrator needs to configure port security on a switch. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN. On switches that are configured to operate in client mode. The network administrator can apply port security to dynamic access ports. B. B. D. C. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration. F.) A. up to the maximum defined. B. E. The network administrator can apply port security to EtherChannels. When switches in VTP client mode are rebooted. or renamed locally. the switch can learn new addresses. deleted. VTP advertisements are not forwarded to neighboring switches that are configured in VTP transparent mode. VTP client is the default VTP mode. no broadcast change of source address in the IPv6 header change of destination address in the IPv6 header Telnet access does not require a password autoconfig NAT . C. STP VTP 802. Which two statements are true? (Choose two. D. VLANs can be created.) A. F. E.

B400.0C07. C. C. D. B. D. D. To report and alert link up / down instances . C. in what order does it pass through each state? A.) A. B. exstart state > loading state > exchange state > full state exstart state > exchange state > loading state > full state exstart state > full state > loading state > exchange state loading state > exchange state > full state > exstart state Correct Answer: B Section: (none) QUESTION 117 What Netflow component can be applied to an interface to track IPv4 traffic? A. D. 0000. To identify applications causing congestion B.C007. To authorize user network access C.1203 0000.0201 Correct Answer: A Section: (none) QUESTION 116 When a router undergoes the exchange protocol within OSPF.Correct Answer: AE Section: (none) QUESTION 114 Which of these represents an IPv6 link-local address? A.0110 0007. B.5E00. flow monitor flow record flow sampler flow exporter Correct Answer: A Section: (none) QUESTION 118 What are three reasons to collect Netflow data on a company network? (Choose three. B. C.AC01 0000. FE80::380e:611a:e14f:3d69 FE81::280f:512b:e14f:3d69 FEFE:0345:5f1b::e14d:3d69 FE08::280e:611:a:f14f:3d69 Correct Answer: A Section: (none) QUESTION 115 Which one of these is a valid HSRP Virtual Mac Address? A.

bandwidth hogs. To detect suboptimal routing in the network F. To diagnose slow network performance. and bandwidth utilization E. To confirm the appropriate amount of bandwidth that has been allocated to each Class of Service Correct Answer: ADF Section: (none) .D.

110. The Boston router was recently installed but connectivity is not complete because of incomplete routing tables.168.184.105 198. D.NAT A network associate is configuring a router for the weaver company to provide internet access.18. and Lancaster.Simulations QUESTION 1 Lab .192.100. Identify and correct any problem you see in the configuration. The ISP has provided the company six public IP addresses of 198. A. The company has 14 hosts that need to access the internet simultaneously.100. B. The hosts in the company LAN have been assigned private space addresses in the range of 192.184. The necessary networking has been completed at each location.OSPF A sporting goods manufacturer has decided to network three (3) locations to improve efficiency in inventory control.17 .30. Note: The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process. The routers have been named to reflect the location: Boston. Frankfurt. and the routers have been configured with single area OSPF as the routing protocol. Correct Answer: Section: IP Routing Technologies QUESTION 2 Lab . C.168.18. .

D. Correct Answer: Section: IP Routing Technologies .A. C. B.