You are on page 1of 35

RuggedSwitch® RSG2100

Hardware Installation Guide

November 1, 2012 www.RuggedCom.com

RuggedSwitch® RSG2100

RuggedSwitch® RSG2100 : Hardware Installation Guide
Copyright © 2012 RuggedCom Inc.

All Rights Reserved
Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights are reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of RuggedCom Inc.

Disclaimer Of Liability
We have checked the contents of this manual against the hardware and software described. However, deviations from the description cannot be completely ruled out. RuggedCom shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this material. The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We appreciate any suggested improvements. We reserve the right to make technical improvements without notice.

Registered Trademarks
ROX™, RuggedBackbone™, RuggedRated™ and eRSTP™ are trademarks of RuggedCom Inc. ROS®, RuggedRouter® and RuggedSwitch® are registered trademarks of RuggedCom Inc. Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the owner. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a world-wide basis.

Third Party Copyrights
RuggedCom recognizes the following third party copyrights: • Copyright © 2004 GoAhead Software, Inc. All Rights Reserved.

Warranty
Five (5) years from date of purchase, return to factory. For warranty details, visit www.ruggedcom.com or contact your customer service representative.

Contacting RuggedCom
Corporate Headquarters RuggedCom Inc. 300 Applewood Crescent Concord, Ontario Canada, L4K 5C7 Tel: +1 905 856 5288 Fax: +1 905 856 1995 Toll-free: 1 888 264 0006 US Headquarters RuggedCom 1930 Harrison St., Suite 209 Hollywood, Florida USA, 33020 Tel: +1 954 922 7938 ext.103 Fax: +1 954 922 7984 Toll-free: 1 888 264 0006 Email: RuggedSales@RuggedCom.com Technical Support Toll Free (North America): 1 866 922 7975 International: +1 905 856 5288 Email: Support@RuggedCom.com Web: www.RuggedCom.com Europe Headquarters RuggedCom Unit 41, Aztec Centre, Aztec West, Almondsbury, Bristol United Kingdom BS32 4TD Tel: +44 1454 203 404 Fax: +44 1454 203 403

RuggedSwitch® RSG2100

Table of Contents
FCC Statement And Cautions ................................................................................................... 6 1. Product Overview ................................................................................................................... 7 1.1. Functional Overview .................................................................................................... 7 1.2. Feature Highlights ....................................................................................................... 7 1.3. Display Panel Description ........................................................................................... 9 2. RuggedSwitch® Modules ..................................................................................................... 11 2.1. Ethernet Panel Description ....................................................................................... 11 3. Installation ............................................................................................................................ 12 3.1. Mounting .................................................................................................................... 12 3.1.1. Rack Mounting ............................................................................................... 12 3.1.2. Panel and DIN Rail Mounting ......................................................................... 13 3.2. Fiber Optic Transceiver Orientation and Connection ................................................ 14 3.2.1. Pluggable Fiber Transceiver Modules ............................................................ 14 3.2.2. Fixed Fiber Transceivers ................................................................................ 15 3.2.3. Power Supply Wiring And Grounding ............................................................. 16 3.2.4. Dielectric Strength (HIPOT) Testing ............................................................... 19 3.2.5. Failsafe Alarm Relay Wiring and Specifications ............................................. 20 3.2.6. Console Port Wiring ....................................................................................... 20 3.2.7. Ethernet Ports ................................................................................................ 21 3.2.8. Pluggable optics – Installation, removal, and precautions .............................. 23 4. Technical Specifications ....................................................................................................... 26 4.1. Power Supply Specifications ..................................................................................... 26 4.2. Failsafe Relay Specifications .................................................................................... 26 4.3. Networking Standards Supported ............................................................................. 26 4.4. Copper Ethernet Port Specifications ......................................................................... 27 4.5. Fiber Optic Specifications ......................................................................................... 27 4.6. Fiber Ethernet Port Specifications ............................................................................ 27 4.6.1. Fast Ethernet (10/100Mbps) Optical Specifications ........................................ 28 4.6.2. Gigabit Ethernet (1Gbps) Optical Specifications ............................................ 28 4.7. PTP Card Specifications ........................................................................................... 29 4.7.1. IRIG-B PWM Input ......................................................................................... 29 4.7.2. IRIG-B Output ................................................................................................. 29 4.8. Operating Environment ............................................................................................. 30 4.9. Mechanical Specifications ......................................................................................... 31 5. EMI And Environmental Type Tests .................................................................................... 32 6. Agency Approvals ................................................................................................................ 34 7. Warranty ............................................................................................................................... 35

RuggedCom® RuggedSwitch®

3

RSG2100 Installation Guide Rev 118

.......... 18 3....................24............................... 14 3.................. 22 3...................................................................... GBIC Orientation for Top and Bottom Row Ports ....................................................................................................................................... DC Single Power Supply Wiring Example ...................................... Micro-D 10/100BaseTX Port Pin Configuration .......................................................................... 21 3.......................................................26... 19 3........... MTRJ 100FX connector .. 13 3............. RSG2100 Rack Mount Chassis Orientation: Front Mount ............................... SFP Orientation for Top and Bottom Row Ports ........................30................................... Rack Mount Adapter Mounting Locations ..... ST 10FL connector .........................................6..8............ 20 3..... 100FX/1000LX LC connector ................................................................................................................... Locking Latch Location on GBIC Optical Modules ............ Ethernet Panel LEDs ..................................................... 15 3..... 11 3...... 18 3.......21................ 17 3........................................11... RSG2100 LED Display Panel ....... AC Single Power Supply Wiring Example ............................... RS2000 Series Phillips Screw Terminal Block .....................2.....................................3................................15.............................20......................................... Micro-D 10/100/1000BaseTX Port Pin Configuration ......23..... 24 3.. 24 3.................14..................................................................... 16 3................................................................................... 15 3...... 11 2................. DC and AC Power Supply Wiring Example ............... 16 3........................................................... 31 RuggedCom® RuggedSwitch® 4 RSG2100 Installation Guide Rev 118 ....................................................................................................................... 22 3........................13.. 15 3.........1........... RS2000 Series Console Cable ..... 12 3....10................... DC Dual Redundant Power Supply Wiring Example ....... 15 3............................. Ethernet and LED Display Panels ............ 1000LX GBIC connector .................................. 100FX/1000LX SC connector ...........................................................................................................................................................................4......................1........ RJ45 Port Pin Configuration ..........................RuggedSwitch® RSG2100 List of Figures 1.27............. 15 3..................................................................................... Panel / DIN Rail Mounting Diagram (Connectors at Top) ..............25........................5....................................................... Chassis Ground Connection ......19....18.................2........1. Failsafe Alarm Relay Wiring .. 20 3..12.......... 22 3.............17..28....................................................................22....................................................................... 25 4................................... 12 3........................ 18 3............16...... 100FX/1000LX ST connector ............................................................ 18 3...............9..................... AC Dual Redundant Power Supply Wiring Example ..................................... Dielectric Strength (HIPOT) Testing ........................ Console Port on Display Board .......7....... 17 3..... RSG2100 Rack Mount Chassis Orientation: Rear Mount ............. 9 2...29...... SFP Removal ....... 1000LX SFP (mini-GBIC) Module and LC connector .................... 15 3.................... RS2000 Series Phoenix Plug Terminal Block ... RSG2100 Mechanical Dimensions .......... 24 3. 21 3...........1................................................

.......................................................... RSG2100 Power Supply Specifications ............. Micro-D 10/100BaseTX Port Pin Assignment ............... 10 3..............2......................................................................... 28 4.......... 22 3...................................... IRIG-B123 AM Output Specifications .......................1.................... 29 4............................................10............................................................7..............11......................... 29 4....................................x) EMI Immunity Type Tests ........4.................6.................................... 26 4............................1...............6................ Agency Approvals ...................................... Fast Ethernet (10/100Mbps) Optical Specifications ....... LED Display – Device status LED behavior definition ............................................. Gigabit Ethernet Optical Specifications .............. Cabling Categories And 1000Base-TX Compliance .................... Port Status LED behavior definition ............ RJ45 Ethernet Pin Assignment ..........2.................................................... 26 4........................ 17 3....................9...........................................1............. IEC 61850-3 EMI Type Tests ........4................................ RSG2100 Power Terminal Block Connection Description ...................................... 34 RuggedCom® RuggedSwitch® 5 RSG2100 Installation Guide Rev 118 ................. IRIG-B PWM Input Specifications ..... 32 5.RuggedSwitch® RSG2100 List of Tables 1......5......... RS232 Over RJ45 Console Cable Pin-out ......................................................................................... 33 6......................... Operating Environment .........................................................................2................... Micro-D 10/100/1000BaseTX Port Pin Assignment .......................3..........3................................................5................. 21 3.............. 27 4.........90.... Failsafe Relay Specifications ..............................1....................... 22 3....................... 29 4................................... 9 1..................... Mechanical Specifications ............................... 26 4........................................................................ 31 5............................. 22 3...... 33 5................. Environmental Type Tests .................................... IEEE 1613 (C37............. Networking Standards Supported ................ 30 4.......................................... Copper Ethernet Port Specifications .......................................... 23 4......... 28 4... IRIG-B003 PWM Output Specifications .............2.1....................3........8........................................

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference on his own expense. RuggedCom® RuggedSwitch® 6 RSG2100 Installation Guide Rev 118 . Attempted service by unauthorized personnel shall render all warranties null and void. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. may cause harmful interference to radio communications. This equipment generates. and is controlled by the authority responsible for the location. Caution: LASER This product contains a laser system and is classified as a CLASS 1 LASER PRODUCT. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Warranty in this guide. could invalidate specifications. Caution: Physical Access This product should be installed in a restricted access location where access can only be gained by service personnel or users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken. Should this device require service. please refer to Chapter 7. if not installed and used in accordance with the instruction manual. test results. or other means of security. and void the user's authority to operate the equipment. and agency approvals. Changes or modifications not expressly approved by RuggedCom Inc.FCC Statement And Cautions FCC Statement And Cautions Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. Caution: Service This product contains no user-serviceable parts. uses and can radiate radio frequency energy and. and access is through the use of a tool or lock and key.

MTRJ • Industry standard transceiver modules: SFP. Functional Overview The RuggedSwitch® RSG2100 is a rugged. activity and speed RuggedRated™ for Reliability in Harsh Environments • Immunity to EMI and heavy electrical transients: • Zero-Packet-Loss™ Technology RuggedCom® RuggedSwitch® 7 RSG2100 Installation Guide Rev 118 .1.2. control applications. The RSG2100 is packaged in a rugged galvanized steel enclosure with industrial grade DIN. Feature Highlights Ethernet Ports • 3-Gigabit Ethernet ports supporting copper and fiber media • 16-Fast Ethernet ports supporting copper and fiber media • Modular port design for unrivalled flexibility • Multimode and Singlemode fiber support • Bi-directional simplex (single strand) fiber support • Full compliance with IEEE: 802. or 19" rack-mount mounting options. LC.3x) • Industry standard fiber optic connectors: LC.3u & 802. GBIC • Long haul optics allow Gigabit at distances of up to 70km Simple Plug and Play Operation • Automatic learning of up to 8192 MAC addresses • Auto-negotiation on all 10/100/1000BaseTX. and micro-D ports • Auto-MDI/MDIX (crossover) on all 10/100BaseTX and micro-D ports • LED indicators for link. Product Overview 1. panel. railway and industrial environments. The RSG2100’s superior rugged hardware design coupled with the embedded Rugged Operating System (ROS™) provides improved system reliability and advanced cyber security and networking features. 1. ST. 802. The RSG2100’s modular flexibility offers 10BaseFL/100BaseFX/1000BaseX fiber and 10/100/1000BaseTX copper port combinations.3. Product Overview 1. fully managed. Optional front or rear mount connectors make the RSG2100 highly versatile for any application and can support multiple fiber connectors (ST. SC. MTRJ. store and forward switching • Full duplex operation and flow control (IEEE 802. modular Ethernet switch specifically designed to operate reliably in electrically harsh and climatically demanding utility substation. SC) without loss of port density.1. making it ideally suited for creating Ethernet networks for mission-critical. real-time.3z • Non-blocking.

1Q with double tagging • GVRP (GARP VLAN Registration Protocol) support: IEEE 802. status. security • SNTP time synchronization (both client and server) • Industrial automation features (e. maintenance-free connections • CSA/UL 60950 safety approved to +85 °C Rugged Operating System (ROS™) Networking Features • MSTP (Multiple Spanning Tree Protocol) support: IEEE 802. statistics. emission and immunity of signalling and telecommunications apparatus) • Exceeds EN 50155 (railway applications: electronic equipment used on rolling stock) • -40°C to +85°C operating temperature (no fans) • Conformal coated printed circuit boards (optional) • 18 AWG galvanized steel enclosure • Hazardous Location Certification: Class 1 Division 2 Universal Power Supply Options • Fully integrated.g.1w • eRSTP™ (Enhanced Rapid Spanning Tree) support.3ad • Loss of link management on fiber ports • Port configuration.1.1D • IGMP Snooping for multicast filtering • Link aggregation support: 802.1Q-2005 • RSTP (Rapid Spanning Tree Protocol) support: IEEE 802. < 5ms network fault recovery • QoS (Quality of Service) support: IEEE 802. Modbus) RuggedCom® RuggedSwitch® 8 RSG2100 Installation Guide Rev 118 .1p. mirroring. dual-redundant (optional) power supplies • Universal high-voltage range: 88-300 VDC or 85-264 VAC • Popular low voltage DC ranges: 12 VDC. for real-time traffic • Port rate limiting and broadcast storm limiting • VLAN (Virtual LAN) support: IEEE 802. Product Overview • Meets IEEE 1613 (electric utility substations) • Exceeds IEC 61850-3 (electric utility substations) • Exceeds IEC 61800-3 (variable speed drive systems) • Exceeds NEMA TS-2 (traffic control equipment) • Exceeds IEC 61000-6-2 (generic industrial environment) • Exceeds EN 50121-4 (railway applications: electromagnetic compatibility. 24 VDC. or 48 VDC • Screw or pluggable terminal blocks for reliable.

which provides real-time status information for each port and for the chassis as a whole. Display Panel Description RS2000 series products are equipped with a versatile display panel. Duplex. LED Display – Device status LED behavior definition RuggedCom® RuggedSwitch® 9 RSG2100 Installation Guide Rev 118 . The following table lists the possible LED colors and their corresponding descriptions. LED Power 1 / Power 2 Color Green Red Off Alarm Red Off Description Power supply operating normally Power supply failure No power supply installed An alarm condition exists – log in to the web management interface or to the CLI to determine the alarm code No alarms exist Table 1. v3 (56-bit encryption) • RMON (Remote MONitoring) • Rich set of diagnostics with logging and alarms 1. RSG2100 LED Display Panel The device status LEDs provide a quick visual indication of the operational status of the unit. Product Overview Rugged Operating System (ROS™) Management Features • Secure Web-based. shown in the following figure. management interfaces • Menu and Command Line based management interfaces via serial port. v2. SSH and Telnet • Remote command execution via RSH • SNMP v1. It features: • RS232 console port for ‘out of band’ console access and configuration • Power supply and Alarm status indicators • Convenient port status indicators conveying Link/Activity.1.3.1.1. or Speed via the Mode pushbutton (toggles between the three display modes) • System reset via the Mode push-button (if held for 5 seconds) Figure 1. to allow simple diagnostics and troubleshooting.

Mode Status Color Green (Solid) Green (Blinking) Off Duplex Green (Solid) Orange (Solid) Off Speed Green (Blinking) Green (Solid) Orange (Solid) Off Description Link detected Activity No link Full-Duplex operation Half-Duplex operation No link 1000Mb/s 100Mb/s 10Mb/s No link Table 1. push the Mode button. Port Status LED behavior definition RuggedCom® RuggedSwitch® 10 RSG2100 Installation Guide Rev 118 .1. To set the display mode.2. and Speed. Duplex. Product Overview The port LEDs operate in three display modes: Status.

2. The figure below shows the physical layout of these ports.2. and blinks for activity. RuggedSwitch® Modules 2. The LED is solid for ports with a valid link. Figure 2.2.1. five of which are modular and may be selected at the time the unit is ordered. Ethernet Panel Description Figure 2. “Ethernet Panel LEDs” shows a copper port module in slot 1 and a fiber module in slot 2. 3 and 4 support two-port Ethernet modules up to 1Gbps. Ethernet Panel LEDs RuggedCom® RuggedSwitch® 11 RSG2100 Installation Guide Rev 118 . Ethernet and LED Display Panels The Ethernet connector panel of the RSG2288 is organized into six slots. Slots 1. along with the link and activity LEDs for each port. RuggedSwitch® Modules 2. Slot 6 contains the PTP Source Card to support advanced time synchronization. Figure 2.2.1. Each Ethernet module is equipped with an LED per port that indicates link/activity status information. Slot 5 supports a oneport module up to 1Gbps.

3. Mounting RSG2000 series products are designed for maximum mounting and display flexibility. Figure 3.1. Secure the rack mount adapter to the front side of the chassis using the included black PAN head Phillips screws in the positions shown in Figure 3. Customers can order an RSG2000 series switch that can be mounted in a standard 19" rack. The entire chassis can then be mounted to a standard 19" rack. or directly onto a panel. RuggedCom® RuggedSwitch® 12 RSG2100 Installation Guide Rev 118 .3.1. Placing the connectors on the rear allows all data and power cabling to be installed and connected at the rear of the rack. Rack Mounting For rack mount installations.1. Installation 3. RSG2100 Rack Mount Chassis Orientation: Front Mount Figure 3. 1" DIN Rail. See the front and rear rack mount chassis orientation options below for examples of rack mount orientation.3. “Rack Mount Adapter Mounting Locations”. Two additional rack mount adapters are included to optionally secure the rear of the chassis in high-vibration or seismically active locations. Installation 3. RSG2100 Rack Mount Chassis Orientation: Rear Mount The RSG2000 family of products can be rack mounted using the included rack mount adapters.2.1. the RSG2000 series can be ordered with connectors on the front panel or on the rear of the chassis.

3. “Panel / DIN Rail Mounting Diagram (Connectors at Top)” for a panel and DIN mounting diagram. Panel and DIN Rail Mounting RS2000 series products can be ordered as panel/DIN mount chassis. any increase in airflow will result in a reduction of ambient temperature that will improve the long-term reliability of all equipment mounted within the rack space.1. Rack Mount Adapter Mounting Locations Since heat within the RSG2100 is channeled to the enclosure.3. Although forced airflow is not necessary. The adapter allows for the chassis to be mounted on a standard 1" DIN rail using the grooves in the adapter.3. Both options involve the use of the panel/DIN adapters to be mounted on each side of the chassis enclosure.4. See Figure 3. and secured using the included Phillips screw.2. Installation Figure 3.75") be kept unpopulated and free of equipment above each RS2000 series product to allow for a small amount of convectional airflow. RuggedCom® RuggedSwitch® 13 RSG2100 Installation Guide Rev 118 . it is recommended that 1 rack-unit of space (1.

The diagrams in this section depict each fiber connector style supported by the RuggedSwitch® in order to provide a reference for the proper orientation of cable connections.e.2. the RS2000 series products can be equipped with several different types of fiber optic ports. 3.1. Note that when the module is installed in the unit. Panel / DIN Rail Mounting Diagram (Connectors at Top) 3.3. RuggedCom® RuggedSwitch® 14 RSG2100 Installation Guide Rev 118 . the transceiver orientation will be inverted relative to the diagram (i. Installation Figure 3. Modules populated on the top row of the device typically have locking mechanisms or tabs facing the top of the unit. The Transmit (TX) and Receive (RX) connections of each port must be properly connected and matched for proper link and operation.4.2. most of the body of the module as shown in top views below will not be visible. Fiber Optic Transceiver Orientation and Connection Depending on the order code of the product. A front view (looking into the connector) and a top view of the connector module are shown for each one. Modules located on the bottom row of the device have locking mechanisms or tabs facing the bottom of the unit. Note that if modules are populated on the bottom row of the device. Pluggable Fiber Transceiver Modules The following figures show front and top views of the pluggable fiber transceiver modules supported by RuggedSwitch®. RX and TX will be reversed).

9. 100FX/1000LX SC connector Figure 3. 100FX/1000LX LC connector Figure 3. 1000LX SFP (miniGBIC) Module and LC connector Figure 3. MTRJ 100FX connector RuggedCom® RuggedSwitch® 15 RSG2100 Installation Guide Rev 118 . most of the connector body as shown in the illustrations is not visible.6. Note that when the module daughter card is installed in the unit. Figure 3.7.2. Fixed Fiber Transceivers The following figures show front and top views of the fixed fiber transceiver modules supported by RuggedSwitch®.5.3.8. ST 10FL connector Figure 3. Installation Figure 3. 1000LX GBIC connector 3.2.10.

The safety cover must be re-attached after wiring to ensure personnel safety. “RS2000 Series Phoenix Plug Terminal Block”.3. Power Supply 1 (PS1) and Power Supply 2 (PS2).12.1.3. Refer to Table 3.3.12.2.2. Installation Figure 3. “AC Power Supply Wiring Examples ”. Both terminal blocks have a safety cover which must be removed via two Phillips screws before connecting any wires.3.13. The connections for PS1.1. The RSG2100 can be equipped with either a Phillips Screw Terminal Block or a Phoenix Pluggable Terminal Block. The Phillips Screw Terminal Block has Phillips screws with compression plates. Power Supply Wiring And Grounding The RSG2100 supports dual redundant power supplies. “RSG2100 Power Terminal Block Connection Description” for a description of each terminal.2. RS2000 Series Phillips Screw Terminal Block RuggedCom® RuggedSwitch® 16 RSG2100 Installation Guide Rev 118 . reliable connections under severe shock or vibration. “AC and DC Power Supply Wiring Example ” for power supply wiring examples. Figure 3.2.3. allowing either bare wire connections or crimped terminal lugs. Refer to Section 3.11.3.2. PS2 and the fail-safe relay are located on the terminal block as shown in Figure 3. 100FX/1000LX ST connector 3. We recommend the use of #6 size ring lugs to ensure secure. “RS2000 Series Phillips Screw Terminal Block” and Figure 3. “DC Power Supply Wiring Examples ” and Section 3. Section 3.

7 Nm). Installation Figure 3. Surge Ground is used as the ground conductor for all surge and transient suppression circuitry.13. Chassis Ground is connected to the Safety Ground terminal for AC inputs or the equipment ground bus for DC inputs.is connected to the negative (-) terminal if the power source is DC or to the (Neutral) terminal if the power source is AC. 3 4 PS1 Neutral / Chassis Ground 5 6 PS2 Live / + PS2 Surge Ground 7 8 9 PS2 Neutral / Relay NO Contact Relay Common RuggedCom® RuggedSwitch® 17 RSG2100 Installation Guide Rev 118 . failsafe relay contact. Figure 3. “Chassis Ground Connection”.is connected to the negative (-) terminal if the power source is DC or to the (Neutral) terminal if the power source is AC. NOTE: Surge Ground must be disconnected from Chassis Ground during HIPOT (dielectric strength) testing. Chassis ground connects to both power supply surge grounds via a removable jumper. shown in Figure 3. PS2 Live / + is connected to the positive (+) terminal if the power source is DC or to the (Live) terminal if the power source is AC. and to use a torque setting not exceeding 15 in•lbs (1.14. PS2 Surge Ground is connected to the Chassis Ground via a jumper on the terminal block. PS1 Surge Ground is connected to the Chassis Ground via a jumper on the terminal block.3. Surge Ground is used as the ground conductor for all surge and transient suppression circuitry. RS2000 Series Phoenix Plug Terminal Block The RSG2100 chassis ground connection. NOTE: Surge Ground must be disconnected from Chassis Ground during HIPOT (dielectric strength) testing. uses a #6-32 screw.14. PS1 Neutral / . It is recommended to terminate the ground connection in a #6 ring lug. Chassis Ground Connection Terminal Number 1 2 Description PS1 Live / + PS1 Surge Ground Usage PS1 Live / + is connected to the positive (+) terminal if the power source is DC or to the (Live) terminal if the power source is AC. Normally open. Failsafe relay common contact. PS2 Neutral / .

16.2.3. 3.1.3.3. independent AC sources can be used to power the product for greater redundancy. Installation Terminal Number 10 Description Relay NC Contact Usage Normally closed. DC Power Supply Wiring Examples + + + Figure 3. • When equipped with two HI voltage power supplies. AC Single Power Supply Wiring Example Figure 3.17. • Equipment must be installed according to the applicable country wiring codes. Table 3. RSG2100 Power Terminal Block Connection Description 3. DC Single Power Supply Wiring Example Figure 3. DC Dual Redundant Power Supply Wiring Example RuggedCom® RuggedSwitch® 18 RSG2100 Installation Guide Rev 118 . AC Power Supply Wiring Examples Figure 3. AC Dual Redundant Power Supply Wiring Example • 100-240VAC rated equipment: A 250VAC appropriately rated circuit breaker must be installed.1. failsafe relay contact.18.15.2.2.

• Equipment must be installed according to the applicable country wiring codes. This metal jumper connects transient suppression circuitry to chassis ground and must be removed in order to avoid damage to transient suppression circuitry during HIPOT testing.2. Dielectric Strength (HIPOT) Testing For dielectric strength (HIPOT) testing in the field. 3. • For dual DC power supplies. Installation • 88-300VDC rated equipment: A 300VDC appropriately rated circuit breaker must be installed. DC and AC Power Supply Wiring Example • 88-300VDC rated equipment: A 300VDC appropriately rated circuit breaker must be installed.3. RuggedCom® RuggedSwitch® 19 RSG2100 Installation Guide Rev 118 .3. • A circuit breaker is not required for 12-24 or 48VDC rated power supplies. • 100-240VAC rated equipment: A 250VAC appropriately rated circuit breaker must be installed. The figure below shows the proper HIPOT test connections and should be followed to avoid damage to the device. 4. separate circuit breakers must be installed and separately identified. • Equipment must be installed according to the applicable country wiring codes.2. AC and DC Power Supply Wiring Example + Figure 3. users must remove the metal jumper located across terminals 2. • Separate circuit breakers must be installed and separately identified.19. • A circuit breaker is not required for 12-24 or 48 VDC rated power supplies. and 6 of the power supply terminal block. 3.3.4.

Console connection settings are: 57600 bps.2. Figure 3. “RS2000 Series Console Cable”. Control of this output is user selectable and can be programmed via the Rugged Operating System (ROS). Installation Figure 3. The proper relay connections are shown in the figure below. This port is intended to be a temporary connection during initial configuration or troubleshooting and allows direct serial access to the management console. Failsafe Alarm Relay Wiring and Specifications The “Failsafe” output relay is provided to signal critical error conditions that may occur on RS2000 series products. One common application for this output is to signal an alarm if a power failure or removal of control power occurs.23. 8 data bits. Dielectric Strength (HIPOT) Testing 3. and 1 stop bit. Console Port Wiring An RS232 console port for configuration and management of the device is located on the LED display module shown in Figure 3. RuggedCom® RuggedSwitch® 20 RSG2100 Installation Guide Rev 118 . Failsafe Alarm Relay Wiring 3. The connection is made using the DB9-Female to RJ45 console cable included in the device packaging shown in Figure 3. no parity bits.3.22.20.5.2.6. The contacts are energized upon power-up of the unit and remain energized unless a critical error occurs. “Console Port on Display Board”.21.

• This port is not intended to be a permanent connection. Installation Figure 3.23.3.1.22. and the built-in secure web server.2. RuggedCom® RuggedSwitch® 21 RSG2100 Installation Guide Rev 118 . RS2000 Series Console Cable Signal Name (PC is DTE) DCD – Carrier detect RxD – Receive data (to DTE) TxD – Transmit data (from DTE) DTR – Data terminal ready GND .Signal ground DSR – Data set ready RTS – Ready to send CTS – Clear to send RI – Ring Indicator DB9.2. The figure below shows the RJ45 port pins configuration. RS232 Over RJ45 Console Cable Pin-out After initial configuration. All RS2000 series RJ45 RuggedSwitch® products feature auto-negotiation.Female 1 2 3 4 5 6 7 8 9 RJ45 Male 2 5 6 3 4 1* 8 7 1* Table 3. the RSG2100 can be configured via a number of networked mechanisms such as Telnet SSH. Ethernet Ports 3. Console Port on Display Board Figure 3.7. RJ45 Twisted-Pair Data Ports RS2000 series Ethernet switches may have several 10/100BaseTX ports that allow connection to standard CAT-5 UTP cable with RJ45 male connectors. and auto-crossover functions.7.2. Consult the ROS™ User Guide for further details. auto-polarity. The RJ45 receptacles can also accept and take advantage of screened (commonly known as “shielded”) cabling.5 ft) in length. • Serial cable must not exceed 2m (6. 3.

5.7. Micro-D 10/100/1000BaseTX Port Pin Configuration 9 Table 3. Micro-D 10/100BaseTX Port Pin Assignment Pin 1 2 3 4 5 6 7 8 Signal TP1+ (B+) TP3+ (D+) No Connection TP2+ (C+) TP0+ (A+) TP1. 7.2. RJ45 Ethernet Pin Assignment 3. 2. However.(C-) TP0.4. transient suppression circuitry is present on all copper ports to protect against damage from electrical transients and to ensure IEC 61850-3 and IEEE 1613 Class RuggedCom® RuggedSwitch® 22 RSG2100 Installation Guide Rev 118 .(A-) Figure 3.(D-) TP2.25. Pin 1 2 3 4 5 6 7 Signal TX+ No Connection No Connection No Connection RX+ TXNo Connection No Connection RX- Figure 3. 9 Description RX + RX TX + TX No Connection Figure 3.2. For 10/100/1000Base-TX ports: Pin 3 and Pin 8 are internally connected on the PCB board.3. Installation Pin 1 2 3 6 4.7.26. For 10/100Base-TX ports: Pin 2 and Pin 7 are internally connected.5. Micro-D Twisted-Pair Data Ports The RSG2100 may have several 10/100/1000BaseTX ports that allow connection to standard CAT-5 UTP cable with Micro-D connectors. RJ45 Port Pin Configuration Table 3.(B-) TP3.24. real-time automation applications. Protection on Twisted-Pair Data Ports RuggedCom does not recommend the use of CAT-5 cabling of any length for critical.3.3. Micro-D 10/100BaseTX Port Pin Configuration 8 9 Table 3. Pin 4 and Pin 8 are internally connected on the PCB board. Micro-D 10/100/1000BaseTX Port Pin Assignment 1. 3.2.

and precautions The RS2000 series of products can be ordered with two pluggable optical form factors: SFP (Small Form-factor Pluggable). No action required. To ensure reliable. Table 3. error-free data communication.4. They include: • Ensuring that dust caps are mounted on SFP cages at all times unless a user is in the process of inserting or removing an SFP module. removal. Power and data cables should intersect at 90° angles when necessary to reduce inductive coupling. “Cabling Categories And 1000Base-TX Compliance” summarizes the relevant cabling standards. or by touching earth or chassis ground before performing installation or RuggedCom® RuggedSwitch® 23 RSG2100 Installation Guide Rev 118 . communications errors or interruptions may occur but recovery is automatic. Cabling Categories And 1000Base-TX Compliance Follow these recommendations for copper data cabling in high electrical noise environments: • Data cable lengths should be as short as possible . Pluggable optics – Installation.6. when inserting or removing optics there are several precautions that should be taken. This means that during the transient event. new and pre-existing communication paths should be verified for TIA/EIA-568-A compliance. and GBIC (GigaBit Interface Converter). Verify TIA/EIA-568-A compliance. This can be accomplished by properly grounding via an ESD wrist strap. system designers and integrators should refer to the Telecommunications Industry Association (TIA) TIA/EIA-568-A wiring standard that characterizes minimum cabling performance specifications required for proper Gigabit Ethernet operation. 3.6. 3. RuggedCom also does not recommend using these ports to interface to field devices across distances which could produce high levels of ground potential rise.8. Gigabit Ethernet 1000Base-TX Cabling Recommendations The IEEE 802.e. Installation 1 conformance. • Shielded/screened cabling can optionally be used. Copper data cables should not be used for inter-building communications.2. • Power and data cables should not be run in parallel for long distances. The dust caps will prevent the accumulation of residue or particles that might inhibit proper operation. No action required. Table 3. Cabling Category <5 5 5e 6 >6 1000BaseTX Compliant No Yes Yes Yes Yes Required Action New wiring infrastructure required. and should be installed in separate conduits.3. Connector and wiring standards to be determined. (i.2. New installations should be designed with Category 5e or higher. greater than 2500V) during line-to-ground fault conditions.7.ideally limited to 3m (10') in length. For wiring guidelines. • Ensuring that the user has properly discharged any possible electrostatic build-up in order to prevent electrostatic discharges (ESD). Nevertheless. SFP and GBIC modules can be safely inserted and removed while the chassis is powered and operating – a feature also referred to as “hot-swappable”. The cable shield should be grounded at one single point to avoid the generation of ground loops.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet communications over distances of up to 100 meters using all 4 pairs in category 5 (or higher) balanced unshielded twisted-pair cabling.

1. • Disconnecting all cables from the SFP or GBIC module prior to insertion or removal of the module. and should always be in place when cables are not connected.28. the figures below show the proper orientation of SFP and GBIC modules installed to both upper and lower slots.8. 3.2. one on either side of the module. Depress both latches simultaneously and gently pull the module from the chassis.29. To remove the SFP module. • Using only optics certified by RuggedCom Inc. Grasp RuggedCom® RuggedSwitch® 24 RSG2100 Installation Guide Rev 118 . To remove a GBIC module.3. Figure 3. Installation removal of optics. The module should be immediately stored in an ESD-safe environment. Locking Latch Location on GBIC Optical Modules 3. GBIC Orientation for Top and Bottom Row Ports Both SFP and GBIC modules should gently slide into their ports and should lock in place when fully inserted. SFP Module Removal SFP Modules are removed using the metal bail latch located on the top of the module.3.2. GBIC Module Removal GBIC modules have two locking latches. free from moisture and stored at the proper temperature (–40 to +85°C). as shown in the figure below.27. and modules on the lower row must be inserted top-side down. disconnect any cables and replace the dust cover to protect the optics. Figure 3.8. Module Insertion – GBIC and SFP Special attention must be paid to the orientation of SFP and GBIC modules upon installation in the RuggedSwitch® chassis. ESD can damage or shorten the life of optical modules when not plugged into a chassis.2.2. 3. with RuggedCom products. For example. SFP modules should be inserted with the bail-latch in the locked position. Dust covers should be in place when installing the modules. disconnect any cables and replace the dust cover to protect the optics. Modules on the upper row must be inserted top-side up. • Ensuring that SFP and GBIC optical modules are always stored in an ESD-safe bag or other suitable ESD-safe environment. Damage can occur to optics and product if compatibility and reliability have not been properly assessed.8. SFP Orientation for Top and Bottom Row Ports Figure 3.

Immediately store the module in an ESD-safe environment. Installation the bail latch and gently pull outwards to unlock and remove the module. SFP Removal RuggedCom® RuggedSwitch® 25 RSG2100 Installation Guide Rev 118 . Figure 3.3.30.

Networking Standards Supported Parameter IEEE 802.1p IEEE 802. Power Consumption 10/100TX FE Ports 15 W 15 W 15 W 15 W Worst Case 30 W 30 W 30 W 30 W 3. 0.2. Failsafe Relay Specifications 4. (F) Denotes fast-acting fuse (T) denotes time-delay fuse. Networking Standards Supported RuggedCom® RuggedSwitch® 26 RSG2100 Installation Guide Rev 118 . Technical Specifications 4.3ab IEEE 802.3af Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 10Mbps Ports Yes Yes Yes Yes Yes Yes Yes Yes 100Mbps Ports 1000Mbps Ports Notes 10BaseT / 10BaseFL 100BaseTX / 100BaseFX 1000BaseSX/LX 1000BaseTx Full Duplex Operation MAC Bridges VLAN (Virtual LAN) Priority Levels Power over Ethernet Ports (17-20) Table 4. c The “HI” power supply is the same power supply for both AC and DC. Power Supply Specifications Power Supply Type 12 – 24 VDC 48 VDC HI (125/250 VDC) HI (110/230 VAC) a b c c a Input Range Min 10 VDC 36 VDC 88 VAC 85 VAC Max 36 VDC 59 VDC 300 VDC 264 VAC Internal Fuse Rating 6.1D IEEE 802. 500VA Table 4.3 IEEE 802. 10/100Base-TX ports consume roughly 1W less than fiber optic ports. Technical Specifications 4. Table 4.3.3x IEEE 802.1. 125VDC 2A @ 240VAC.2. Failsafe Relay Specifications Parameter Max Switching Voltage Rated Switching Current Max Switching Capacity Value (Resistive Load) 240VAC.1Q IEEE 802.15A(T) 2A(T) 2A(T) cb cb Power consumption varies based on configuration.3.3A(F) b b Max.15A @ 125VDC.3z IEEE 802.3u IEEE 802. RSG2100 Power Supply Specifications 4. 2A @ 30VDC 150W.4.1.

4. Technical Specifications 4. Module order codes are contained within each product when assembled and configured at the factory. Fiber Optic Specifications The following sections list fiber optic specifications for ports that can be ordered with an RS2000 series Ethernet switch. The following sections list specifications for fiber optic modules in Fast Ethernet(10/100Mbps) and Gigabit Ethernet (1000Mbps). Copper Ethernet Port Specifications 4. Auto-negotiating Shielded/Unshielded Auto-Crossover. Copper Ethernet Port Specifications Parameter Speed Duplex Cable-Type Wiring Standard Max Distance Connector Isolation Specification 10/100 Mbps FDX / HDX ≥ Category 5 TIA/EIA T568A/B 100 m RJ45 1. RuggedCom® RuggedSwitch® 27 RSG2100 Installation Guide Rev 118 . Auto-Polarity Table 4. Consult the RuggedCom ROS® User Guide for help in obtaining the factory configuration data.6. and can determine the modules installed on a particular unit by reading the factory data file via the RuggedSwitch ROS® user interface.4.5. The user determines the type of optics at the time of ordering. 4. Fiber Ethernet Port Specifications The specifications are organized by signaling speed and then by order code.4.5kV RMS 1-minute Notes Auto-negotiating.

Technical Specifications 4.5.5 -22.5/125 50/125 9/125 9/125 9/125 9/125 62.5 -3 -3 0 5 -3 -3 -3 -20 -20 -21 -24 -20 -20 -20 -20 -21 -23 -23 -23 -22 -22 -21 0 0 -3 -3 -3 -3 0 0 -3 -3 -3 -3 -3 -3 -3 Typical Distance (km) 0.6.55 10 25 40 70 10 10 10 Power Budget (dB) 10.9 -33.4 14.7 10 25 10 25 0.4 11.5/125 9/125 9/125 9/125 9/125 9/125 9/125 9/125 Tx Tx Rx Rx min max Sensitivity Saturation (dBm) (dBm) (dBm) (dBm) -16 -19.2 -11. Gigabit Ethernet (1Gbps) Optical Specifications 4.5 -9.5 -9.2.6. Fast Ethernet (10/100Mbps) Optical Specifications Order Code Speed Mode / Cable Standard Connector Tx λ (nm) Type (µm) 10FL 10FL 100FX MM/ST SM/ST MM/ST 820 1310 1300 62.5 -32 -34 -31 -38 -34 -35 -37 -37 -11.5 -19 -22.5 20 17 23 13 13 11.5/125 50/125 9/125 9/125 9/125 9/125 SIMPLEX 9/125 SIMPLEX 9/125 9/125 -9.5 -19 -19 -15 -15 -15 -5 -5 0 0 -9 -12.8 -14 -14 -14 -14 -14 -14 -14 -14 -7 -8 -8 0 0 5 5 -34 -34 -35 -33.5 -2.6.2 -3 -14 -14 -14 -14 -14 -14 -14 -3 -7 -3 -3 -3 0 0 Typical Distance (km) 2 2 5 2 2 2 2 2 2 2 20 20 20 50 50 90 90 Power Budget (dB) 18 14.5 10.5 -5 -10 -5 -9 -9 -9.1.5/125 50/125 62.2.5 -4 -4 -3 0 -3 0 -2.9 11 14.8 -27 -19 -22.5 11.5 -7 -6 0 -9 -9 -9.5 12-11-0036 12-11-0027 12-11-0028 12-11-0025 12-11-0026 25-10-0111 25-10-0100 25-10-0101 25-10-01085 25-10-01094 25-10-0202 25-10-02034 25-10-0102 RuggedCom® RuggedSwitch® 28 RSG2100 Installation Guide Rev 118 .4 0.5/125 50/125 50/125 62.2 8 14.1.5 13 19 16 23 29 30 42 37 12-11-0011 12-11-0012 12-11-0007 12-11-0009 100FX MM/SC 1300 12-11-0008 12-11-0046 12-11-0006 12-11-0005 12-11-0004 12-11-0031 12-11-0032 12-11-0033 12-11-0034 100FX 100FX 100FX 100FX 100FX 100FX 100FX 100FX 100FX MM/MTRJ MM/LC SM/ST SM/SC SM/LC SM/SC SM/LC SM/SC SM/LC 1300 1310 1310 1300 1300 1310 1310 1310 1310 Table 4.9 -33.) min max Sensitivity Saturation Standard Connector Type (µm) (nm) (dBm) (dBm) (dBm) (dBm) 1000SX 1000LX 1000LX 1000LX 1000LX 1000SX 1000LX 1000LX 1000LX 1000LX 1000BX 1000BX 1000LX MM/LC MM/LC SM/LC SM/LC SM/SC SM/SC MM/LC SM/LC SM/LC SM/LC SM/LC SM/SC SM/SC SM/SC 850 850 1310 1310 1310 1310 850 850 1310 1310 1550 1550 1310 1490 1310 62.4. Fast Ethernet (10/100Mbps) Optical Specifications 4.5 -33.3 0.5/125 62.5 19 10 15 11 11 11.9 11. Fixed Gigabit Transceivers Order Code Tx Tx Rx Rx Speed Mode / Cable Tx λ (typ.9 -33.5/125 50/125 9/125 62.9 -33.

IRIG-B PWM Input Parameter Input Voltage Input Impedance Typical Value TTL-Compatible >200kΩ Table 4. All optical power numbers are listed as dBm averages. 5. 2. Gigabit Ethernet Optical Specifications 1.4. These transceivers utilize a distributed feedback (DFB) type laser and are rated for -20°C to +85°C operation only.8. 3. IRIG-B Output Parameter Output Current (Is) Output Voltage (Vs) Output Impedance (Rs) Typical Value 100 mA 5 Vp-p 50Ω Table 4. PTP Card Specifications 4.9. Technical Specifications Order Code 25-10-0103 25-10-01134 Tx Tx Rx Rx Speed Mode / Cable Tx λ (typ. IRIG-B PWM Input Specifications 4.7.7. Maximum segment length is greatly dependent on factors such as fiber quality. 4. 4. IRIG-B123 AM Output Specifications RuggedCom® RuggedSwitch® 29 RSG2100 Installation Guide Rev 118 . and has been replaced with the 70 km 25-10-0109 SFP module. All cabling is duplex type unless otherwise specified.1.7.) min max Sensitivity Saturation Standard Connector Type (µm) (nm) (dBm) (dBm) (dBm) (dBm) 1000LX 1000LX SM/SC SM/SC 1310 1550 9/125 9/125 -3 0 2 5 -23 -23 -3 -3 Typical Distance (km) 25 70 Power Budget (dB) 20 23 Table 4. The 25-10-0108 SFP module is obsolete.7. Please consult RuggedCom sales associates when determining maximum segment distances. and number of patches and splices. IRIG-B003 PWM Output Specifications Parameter Carrier Frequency Modulation Depth Output Current (Is) Output Impedance (Rs) Output Voltage (Vs) Typical Value 1 kHz 3:1±10% 24 mA 10Ω 6 Vp-p Table 4.6.2.

8. Operating Environment RuggedCom® RuggedSwitch® 30 RSG2100 Installation Guide Rev 118 . Non-condensing Table 4. Technical Specifications 4.4. Operating Environment Parameter Ambient Operating Temperature Ambient Relative Humidity Ambient Storage Temperature Range -40 to 85°C 5% to 95% -40 to 85°C Comments Ambient Temperature as measured from a 30cm radius surrounding the center of the enclosure.10.

20 mm) 10 lb (4. Mechanical Specifications Parameter Dimensions Weight Enclosure Value 18.74 in (464. RSG2100 Mechanical Dimensions RuggedCom® RuggedSwitch® 31 RSG2100 Installation Guide Rev 118 .57 × 258. Mechanical Specifications Figure 4.4.9. Technical Specifications 4.5 kg) 18AWG galvanized steel Comments (Length × Width × Height) with mounting brackets installed Table 4.1.32 × 44.17 × 1.11.29 × 10.

EMI And Environmental Type Tests 5. +/.C. Impulse D. Power ports Signal ports IEC 60255-5 a Severity Levels 4 4 Note Note 4 4 4 4 3 4 3 3 3 3 Note 5 N/A N/A N/A 3 3 3 4 4 3 N/A N/A N/A N/A N/A N/A a a a 30% for 0. Power ports Signal ports IEC 61000-4-12 Damped Oscillatory D. Power ports A.C.C. +/.1s. mode@1MHz 30V Continuous.5kV common. Power ports D.5kVDC 2kVAC 5kV (Fail-Safe Relay output) 5kV 5kV H.4kV @ 2.5kV common.1s.C. 1000 A/m for 1 s 1000 A/m for 1 s D.C. 60% for 0.C Power ports A.C. EMI And Environmental Type Tests Test IEC 61000-4-2 IEC 61000-4-3 ESD Radiated RFI Description Enclosure Contact Enclosure Air Enclosure Ports Signal ports IEC 61000-4-4 Burst (Fast Transient) D.5kHz +/.1. Power ports A.C. Power ports A. Power ports A.V. 1kV diff. mode@1MHz 2.5. 100% for 50 periods 2. Power ports Signal ports IEC 60255-5 Dielectric Strength D.C. 300V for 1s 30V Continuous.C.4kV +/.5kV common.4kV +/. 300V for 1s 10% 2kVAC (Fail-Safe Relay output) 1. 1kV diff.4kV line-to-earth. Power ports Earth ground ports IEC 61000-4-8 Magnetic Field Enclosure Ports Test Levels +/. continuous.C.C.1kV line-to-line +/.05s 30% for 1 period.C. Power ports IEC 61000-4-11 Voltage Dips & Interrupts A. 100% for 0.C. Power ports RuggedCom-specified severity levels Table 5.8 kV +/.15 kV 20 V/m +/.C.C.C. +/. Power Supply Signal ports D.2kV line-to-earth. Power ports Signal ports IEC 61000-4-6 Induced (Conducted) RFI D. Power ports Earth ground ports Signal ports IEC 61000-4-5 Surge D. Power ports A. 1kV diff. IEC 61850-3 EMI Type Tests RuggedCom® RuggedSwitch® 32 RSG2100 Installation Guide Rev 118 . Power ports IEC 61000-4-29 Voltage Dips & Interrupts A. Power ports IEC 61000-4-16 IEC 61000-4-17 Mains Frequency Voltage Ripple on D.4kV +/.4kV line-to-earth.2kV line-to-line 10V 10V 10V 10V 40 A/m.2kV line-to-line +/. mode@1MHz 2.C. 60% for 50 periods 100% for 5 periods.

C. Environmental Type Tests RuggedCom® RuggedSwitch® 33 RSG2100 Installation Guide Rev 118 .90.90. Power ports Signal ports IEEE C37. Test IEC 60068-2-1 IEC 60068-2-2 IEC 60068-2-30 IEC 60255-21-1 IEC 60255-21-2 a Description Cold Temperature Dry Heat Humidity (Damp Heat. EMI And Environmental Type Tests Test IEEE C37.C. IEEE 1613 (C37.C.4kV 2.4kV +/. Power ports A.5kV common.150) Hz 30g @ 11mS Severity Levels N/A N/A N/A Class 2 Class 2 a a Class 2 refers to “Measuring relays and protection equipment for which a very high security margin is required or where the vibration levels are very high. Power ports Earth ground ports Signal ports IEEE C37.90. 6 cycles 2g @ (10 . • If the unit contains all fiber ports the IEEE 1613 conformance is Class 2 (During disturbance no errors will occur).15kV 35 V/m +/.V.90.” Table 5.C. mode@1MHz 2.5kV common.90.x) EMI Immunity Type Tests Meets Class 2 requirements for an all fiber configuration.C.C.1 Fast Transient D.3.3 IEEE C37.5kHz +/.C.8kV +/. Power ports A.4kV @ 2. mode@1MHz 5kV (Fail-Safe Relay output) 5kV 5kV 2kVAC 1.1 Oscillatory D.2. Cyclic) Vibration Shock Test Ad Test Bd Test Db Test Levels -40°C.C.5. meets Class 1 for copper ports: • If the unit contains copper ports. for shipboard applications and for severe transportation conditions.5kV common mode @1MHz 2. Power ports A. Power ports A. 16 Hours +85°C. Power ports Table 5. the IEEE 1613 conformance is Class 1 (During disturbance errors may occur but recovery is automatic).90 H. 1kV diff.2 ESD Radiated RFI Description Enclosure Contact Enclosure Air Enclosure ports Signal ports Test Levels +/. 16 Hours 95% (non-condensing). 55°C .5kVDC 2kVAC IEEE C37.4kV +/. Power ports Signal ports IEEE C37.90 Dielectric Strength D.g. e. 1kV diff. Impulse D.

2 No.1. Agency Approvals 6. Subchapter J EN60825-1:1994 + A11:1996 + A2:2001 ISO9001:2000 Comments Passed Passed Passed Passed Passed Passed Passed Designed and manufactured using a ISO9001: 2000 certified quality program Table 6. Class A 21 CFR Chapter 1. EN 61000-6-2 FCC Part 15. Agency Approvals Agency CSA UL CE FCC CISPR FDA/CDRH IEC/EN ISO Standards CSA C22.6. Class A EN55022. 60950 UL 60950 EN 60950. Agency Approvals RuggedCom® RuggedSwitch® 34 RSG2100 Installation Guide Rev 118 .

Attempted service by unauthorized personnel shall render all warranties null and void.7. contact the factory at: RuggedCom Inc. This product contains no user-serviceable parts. Warranty 7. For warranty details.RuggedCom. 300 Applewood Crescent Concord. visit www.com or contact your customer service representative. Ontario Canada L4K 5C7 Phone: +1 905 856 5288 Fax: +1 905 856 1995 RuggedCom® RuggedSwitch® 35 RSG2100 Installation Guide Rev 118 . Should this product require service. Warranty RuggedCom warrants this product for a period of five (5) years from the date of purchase.