You are on page 1of 136

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation

Guide

Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883

Last Revised: December 17, 2012 Text Part Number: OL-16215-10

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: • Turn the television or radio antenna until the interference stops. • Move the equipment to one side or the other of the television or radio. • Move the equipment farther away from the television or radio. • Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental. Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide © 2012 Cisco Systems, Inc. All rights reserved.

CONTENTS
Preface
vii vii vii viii viii xv xvi xvi

Objective Audience Conventions

Organization

Related Documentation

Searching Cisco Documents

Obtaining Documentation and Submitting a Service Request
1

CHAPTER

Product Overview

1-1 1-2 1-2 1-3

General Description Cisco 860 Series ISRs

Cisco 860VAE Series ISRs Interfaces 1-3 IOS Images 1-4

Cisco 880 Series ISRs 1-6 Cisco 880 Series Data Routers 1-6 Cisco 880 Series Voice and Data Routers 1-9 Cisco 881 SRST and Cisco 888 SRST 1-9 Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W 1-13 Cisco 880 Series with Embedded WLAN Antennas 1-15 Cisco 887VA-WD 1-15 C881WD 1-16 Cisco 890 Series ISRs 1-17 Cisco 891, Cisco 892, and Cisco 892F 1-17 Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA

1-20

Hardware Features 1-27 Kensington Lock 1-27 Reset Button 1-27 Cisco 860VAE Routers—Custom Configuration File 1-27 Custom Configuration File for Cisco 892FSP, 896VA, 897VA, and Cisco 898EA 1-28 LEDs 1-30 Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers 1-35 Memory 1-36
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10

iii

or Workstation Connecting a Phone 3-6 3-4 3-5 Connecting an External Ethernet Switch Connecting the V.Contents USB Port 1-37 Fan 1-37 Power Supply 1-38 Power over Ethernet Module 1-38 3G Cellular Data WAN Connectivity 1-38 Wireless LAN Connectivity 1-39 Supported Cisco Radio Antennas 1-40 Small Form-Factor Pluggable Port 1-40 Feature Summary 1-41 2 CHAPTER Installing the Router 2-1 Equipment. Server. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide iv OL-16215-10 . Tools. and Connections 2-2 Items Shipped with your Router 2-2 Additional Items 2-2 Connections 2-3 Ethernet Devices 2-3 Installing the Router 2-3 Warnings 2-4 Installing Antennas 2-4 Installing on a Table 2-7 Mounting on a Wall 2-8 Installing in a Rack 2-11 Installing the Router Ground Connection Installing the FIPS Cover 2-14 3 2-13 CHAPTER Connecting the Router Safety Warnings 3-2 3-1 Preparing to Connect the Router 3-4 Preventing Damage to the Router Connecting a PC.92 modem Port 3-8 3-7 Connecting a Terminal or PC to the Console Port Terminal Emulator Settings 3-10 Connecting a Modem to the Auxiliary Port Connecting the 3G Card 3-11 3-10 3-9 Installing the 3G Adapter for Extended Cable/Antenna 3-17 Cisco 860 Series.

Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 v .92 Port Connector Pinouts A-6 A-6 A-7 A-5 A-5 A-5 G.SHDSL Port Connector Pinouts Data BRI Port Connector Pinouts SFP Port Connector Pinouts A-8 Voice ISDN BRI Interface Pin Numbers and Functions A-7 Cisco 860 Series.Contents Connecting a Data BRI Port 3-21 3-23 3-24 Connecting an FE Line to an FE WAN Port Connecting a GE Line to an GE WAN Port Connecting an xDSL Line Connecting the AC Adapter Connecting an FXS Line Connecting an FXO Line 3-25 3-27 Connecting Power over Ethernet 3-28 3-32 3-34 Connecting a Voice ISDN BRI Line 3-35 3-37 Connecting a Small Form-Factor Pluggable Module Safety Warnings 3-37 Installing an SFP Module 3-38 Removing an SFP Module 3-38 Online Insertion and Removal 3-39 Verifying Connections 4 3-40 CHAPTER Initial Configuration Cisco IOS CLI 4-1 4-1 4-1 Cisco Configuration Professional Express Setup Command Facility 4-3 4-5 Verifying the Initial Configuration Initial Configuration of the Wireless Access Point A 4-6 APPENDIX Technical Specifications Router Specifications Wireless Access Point FE and GE Port Pinouts A-1 A-2 A-3 A-3 A-4 Console and Auxiliary Port Connector Pinouts FXS and FXO Port Connector Pinouts VDSL2 Port Connector Pinouts ADSL2+ Port Connector Pinouts V.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide vi OL-16215-10 .Contents Cable Specifications A-8 Ethernet Cable Specifications A-9 Maximum Cable Length A-9 Cisco 860 Series. Cisco 880 Series.

page xv Searching Cisco Documents. page xvi Objective This guide provides an overview and explains how to install. see the “Cisco One-Year Limited Hardware Warranty Terms” section in Readme First for the Cisco 800 Series Integrated Services Routers that was shipped with your router. and perform initial configuration for the wireless and nonwireless Cisco 860 series. page xvi Obtaining Documentation and Submitting a Service Request. page viii Conventions. page vii Audience. Cisco 860 Series. It contains the following sections: • • • • • • • Objective. and support information. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 vii . service. page vii Organization. page viii Related Documentation. and Cisco 890 series Integrated Services Routers (ISRs). Cisco 880 series. audience. connect. Some information may not apply to your particular router model. organization. Audience This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar with Cisco routers and Cisco IOS software and features. and conventions of this guide. and describes related documents that have additional information. For warranty.Preface This preface describes the objectives.

and how to verify the connections. Caution This symbol means reader be careful. “Technical Specifications” Provides the router. “Initial Configuration” Appendix A. “Connecting the Router” Chapter 4 Appendix A Chapter 4. Notes contain helpful suggestions or references to additional information and material. but could be useful information. port. Cisco 880 Series. Chapter 3 Chapter 3. Describes typical connections for the router. In this situation. procedures for connecting the router to various devices. and the procedures for installing the router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide viii OL-16215-10 . Chapter Chapter 1 Chapter 2 Name Chapter 1. Provides the procedures for initially configuring the router settings. you might do something that could result in equipment damage or loss of data. “Installing the Router” Description Describes the router models and the hardware features available.Preface Organization This guide is organized into the following chapters and appendix. The tip information might not be troubleshooting or even an action. Conventions This section describes the conventions used in this guide. the safety warnings and guidelines. the equipment and tools necessary for installing the router. and cabling specifications. Cisco 860 Series. Note Means reader take note. Lists the items shipped with the router. “Product Overview” Chapter 2. Tip Means the following information will help you solve a problem.

Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd. CONSERVEZ CES INFORMATIONS Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. You are in a situation that could cause bodily injury. be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil. huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Voordat u aan enige apparatuur gaat werken. Sie befinden sich in einer Situation. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. BEWAAR DEZE INSTRUCTIES Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 ix . Cisco 880 Series. die zu Verletzungen führen kann. dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Avant de travailler sur un équipement. Before you work on any equipment. Tilanne voi aiheuttaa ruumiillisia vammoja. die zusammen mit diesem Gerät ausgeliefert wurden.Preface Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. Statement 1071 SAVE THESE INSTRUCTIONS Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Cisco 860 Series. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. Ennen kuin käsittelet laitteistoa. wilt raadplegen. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen. SÄILYTÄ NÄMÄ OHJEET Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. BEWAHREN SIE DIESE HINWEISE GUT AUF.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. TA VARE PÅ DISSE INSTRUKSJONENE Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. GUARDE ESTAS INSTRUÇÕES ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Cisco 880 Series. considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Du befinner dig i en situation som kan leda till personskada. Existe riesgo para su integridad física. Du er i en situasjon som kan føre til skade på person. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. Prima di intervenire su qualsiasi apparecchiatura. Før du begynner å arbeide med noe av utstyret. CONSERVARE QUESTE ISTRUZIONI Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Você está em uma situação que poderá ser causadora de lesões corporais. SPARA DESSA ANVISNINGAR Cisco 860 Series. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. må du være oppmerksom på farene forbundet med elektriske kretser. GUARDE ESTAS INSTRUCCIONES Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. La situazione potrebbe causare infortuni alle persone. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide x OL-16215-10 . Antes de manipular cualquier equipo. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. Antes de iniciar a utilização de qualquer equipamento. og kjenne til standardprosedyrer for å forhindre ulykker.Preface Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 xi .Preface Cisco 860 Series. Cisco 880 Series.

Preface Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. GEM DISSE ANVISNINGER Cisco 860 Series. Cisco 880 Series. og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Você se encontra em uma situação em que há risco de lesões corporais. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xii OL-16215-10 . der er ved elektriske kredsløb. esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. der fulgte med denne enhed. Antes de trabalhar com qualquer equipamento. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr. skal du være opmærksom på de involverede risici. GUARDE ESTAS INSTRUÇÕES Advarsel VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler.

Preface Cisco 860 Series. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 xiii .

Statement 1038 Cisco 860 Series. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. or near a swimming pool. near a bath tub. Using any other cables/adaptors could cause a malfunction or a fire. Dispose of used batteries according to the manufacturer’s instructions. Statement 1035 Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. wash bowl. Statement 1015 Warning Do not use this product near water. Statement 1036 Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. in a wet basement.Preface Warning When installing the product. There may be a remote risk of electric shock from lightning. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xiv OL-16215-10 . Statement 371 Warning There is the danger of explosion if the battery is replaced incorrectly. Cisco 880 Series. please use the provided or designated connection cables/power cables/AC adaptors. Statement 1037 Warning Avoid using a telephone (other than a cordless type) during an electrical storm. kitchen sink or laundry tub. for example. Replace the battery only with the same or equivalent type recommended by the manufacturer.

Statement 1030 Warning Read the installation instructions before connecting the system to the power source. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 xv . Release 12. Release 12. and Cisco 890 Series Integrated Services Routers Software Configuration Guide Software Activation on Cisco Integrated Services Routers and Cisco Integrated Service Routers G2 Cisco IOS Software Activation Configuration Guide Declarations of Conformity and Regulatory Information for Cisco Access Products with 802. Cisco 880 Series. and Cisco 890 series ISR Hardware Installation Guide (this document). Release 12. Statement 1040 Related Documentation In addition to the Cisco 860 series.11b/g Radios Cisco IOS Release Notes Cisco IOS Quality of Service Solutions Command Reference. and Cisco 890 series ISR documentation set includes the following documents: • • • • • • • • • • • • • • • Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers Cisco 860 Series. the Cisco 860 series. Cisco 880 Series. Statement 1004 Warning Ultimate disposal of this product should be handled according to all national laws and regulations.3(8) JEC Wireless LAN Controllers Unified Wireless LAN Access Points Cisco IOS Voice Port Configuration Guide SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways Cisco CP Express User’s Guide Cisco 860 Series. replace.Preface Warning Only trained and qualified personnel should be allowed to install. Cisco 880 series.4T Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges.4T Cisco IOS Security Command Reference.4(10b) JA and 12. versions 12. or service this equipment. Cisco 880 series.4T Cisco IOS Security Configuration Guide.11a/b/g and 802.

html Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application.com/en/US/docs/general/whatsnew/whatsnew. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide xvi OL-16215-10 . press Ctrl-F (Windows) or Cmd-F (Apple). which also lists all new and revised Cisco technical documentation: http://www. Obtaining Documentation and Submitting a Service Request For information on obtaining documentation. see the monthly What’s New in Cisco Product Documentation.cisco. In most browsers. To search a PDF document in Adobe Reader. the option to search whole words only.Preface Searching Cisco Documents To search a HTML document using a web browser. invoke case sensitivity. Cisco 880 Series.0. Use the Find toolbar to find words or phrases within a specific document. The RSS feeds are a free service. and gathering additional information. submitting a service request. Cisco 860 Series. Adobe Reader’s online help has more information about how to search PDF documents. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. Cisco currently supports RSS Version 2. use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). or search forward and backward is also available.

Port and feature locations are similar for both wireless and nonwireless routers. Cisco 860 Series. and Cisco 890 series Integrated Services Routers (ISRs). ADSL2. Both wireless and nonwireless models are available in the Cisco 860 series. page 1-27 Note For compliance and safety information. page 1-3 Cisco 880 Series ISRs. and contains the following sections: • • • • • • General Description. & G.5). & ADSL2+ (ITU G. page 1-17 Hardware Features.992. Cisco 880 series. and Cisco 890 series ISRs.1.992. page 1-6 Cisco 890 Series ISRs. page 1-2 Cisco 860 Series ISRs.2) and ADSL refers to support for ADSL. G. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-1 .CH A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco 860 series. Note Throughout this document the term VDSL refers to support for VDSL2 (ITU G. Note Some illustrations in this document show a wireless router. see Regulatory Compliance and Safety Information Roadmap that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.992. Cisco 880 Series.3.993. Cisco 880 series. page 1-2 Cisco 860VAE Series ISRs.

quality of service (QoS). Wi-Fi CERTIFIED™ wireless access point (AP). firewall.Chapter 1 General Description Product Overview General Description The Cisco 860 series. Optional. antivirus protection.11b/g/n-compliant wireless AP Figure 1-1 shows the front panel details of the Cisco 860 wireless router. These ISRs are powered by an external power supply adapter. integrated Virtual Private Network (VPN). The routers provide advanced features. Figure 1-1 Front Panel of the Cisco 860 Series Wireless ISR 1 1 LEDs Cisco 860 Series. The Cisco 860 series. embedded Wi-Fi CERTIFIED™. The various models differ in the WAN interface and features that they support. and Cisco 890 series ISRs provide data. 886VA and 887VA series routers have the additional capability of DSL Multi-mode (VDSL/ADSL). 802. and Secure Socket Layer (SSL).11n. The Cisco 860VAE. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-2 OL-16215-10 231969 . Cisco 880 Series. such as high speed DSL (G. Cisco 860 Series ISRs The Cisco 860 series ISRs are fixed-configuration data routers that support the following features: • • • An integrated 4-port 10/100 Ethernet switch for connecting to the LAN A10/100 Fast Ethernet (FE) port for connecting to the WAN. or VDSL). 802. and Cisco 890 series ISRs have a desktop form factor with built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. Cisco 880 series. ADSL. and backup capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users.SHDSL. These routers are capable of bridging and multiprotocol routing between LAN and WAN ports. Cisco 880 series. voice.

However.Chapter 1 Product Overview Cisco 860VAE Series ISRs Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. This section describes the features of the products in this series. Interfaces Table 1-1 describes the interfaces of the Cisco 860VAE series routers. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-3 232181 . Figure 1-2 Back Panel of the Cisco 861W ISR Cisco 861W WAN FE 4 1 2 3 4 5 6 7 8 1 2 3 4 Primary WAN port—10/100 Antenna—captive omnidirectional dipole WLAN antenna (wireless models only) 4-port 10/100 Ethernet switch Serial port—console or auxiliary 5 6 7 8 Reset button Power connector Earth ground connection Kensington security slot Cisco 860VAE Series ISRs The Cisco 860VAE series ISRs are fixed-configuration data routers. Table 1-1 Interfaces of the Cisco 860VAE Series ISRs Model Interfaces 4 FE switch ports 1 GE switch port 1 GE WAN port 2 1 866VAE x — x 867VAE x — x 866VAE-K9 x x x 867VAE-K9 x x x Cisco 860 Series. Nonwireless routers do not have antennas on the back panel. the feature locations are similar for all Cisco 860 series routers.

Figure 1-3 Cisco 860 Series Front Panel of the Cisco 860VAE series ISR 1 1 LEDs Cisco 860 Series. Cisco 867VAE. Cisco 866VAE-K9. Table 1-2 IOS Images of the Cisco 860VAE Series ISRs Model IOS Image c860vae-ipbasek9-mz c860vae-advsecurityk9-mz c860vae-advsecurityk9_npe-mz 866VAE x — — 867VAE x — — 866VAE-K9 — x x 867VAE-K9 — x x Figure 1-3 shows the front panel details of the Cisco 866VAE. 867VAE. IOS Images Table 1-2 describes the IOS images included in Cisco 860VAE series routers. 866VAE-K9. and Cisco 867VAE-K9 integrated services routers (ISRs). FE = Fast Ethernet 2. GE = Gigabit Ethernet 866VAE — x 867VAE x — 866VAE-K9 — x 867VAE-K9 x — Note The Cisco 866VAE. Cisco 880 Series. and 867VAE-K9 routers each have two WAN ports. Only one of the two ports can be active at any given time. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-4 OL-16215-10 246199 .Chapter 1 Cisco 860VAE Series ISRs Product Overview Table 1-1 Interfaces of the Cisco 860VAE Series ISRs (continued) Model Interfaces 1 VDSL/ADSL over POTS port 1 VDSL/ADSL over ISDN port 1.

5A RESET 1 1 2 3 4 5 xDSL port1 2 3 6 7 8 9 4 On/Off switch 5 6 7 8 9 GE WAN interface Ethernet LAN FE interfaces (FE0 through FE3 interfaces) USB port Serial port—console or auxiliary Power connector Reset button Kensington security slot 1.5A RESET 1 1 2 3 4 5 xDSL port 2 3 6 7 8 9 4 On/Off switch 5 6 7 8 9 GE WAN interface Ethernet LAN GE and FE interfaces (GE0 interface and FE0 through FE3 interfaces) USB port Serial port—console or auxiliary Power connector Reset button Kensington security slot Cisco 860 Series. Figure 1-5 shows the back panel details of the Cisco 867VAE-K9. Cisco 880 Series.Chapter 1 Product Overview Cisco 860VAE Series ISRs Figure 1-4 shows the back panel details of the Cisco 866VAE ISR. Figure 1-5 Back Panel of the Cisco 867VAE-K9 ISR Cisco 867VAE-K9 VDSL/ADSL WAN LAN CONSOLE 12V 2. Using RJ-11. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-5 284558 OVER POTS GE1 GE0 FE3 FE2 FE1 FE0 AUX 246200 OVER ISDN GE0 FE 3 FE 2 FE 1 FE 0 AUX . Figure 1-4 Back Panel of the Cisco 866VAE ISR Cisco 866VAE VDSL/ADSL WAN LAN CONSOLE 12V 2.

Figure 1-6 through Figure 1-9 show the features available on Cisco 880 series data routers. for a total of 768 MB system memory USB 1. VDSLoPOTS.11b/g/n-compliant wireless AP. or 10/100 FE. The USB port and the 3G card slot are located on the front panel. Cisco 860 Series. Figure 1-6 shows the front panel details of the Cisco 880 wireless data router. embedded Wi-Fi CERTIFIED™. Cisco 880 Series. • DIMM expansion socket that can accept up to 512 MB of additional memory. Depending on the router model. the primary WAN port can be G. Some of the features shown may not be available on your router. If this feature was not configured with the factory order.11b/g/n-compliant wireless AP Optional 2-port Power over Ethernet (PoE) • • Note The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.Chapter 1 Cisco 880 Series ISRs Product Overview Cisco 880 Series ISRs The Cisco 880 series ISRs have data and voice capabilities. ADSL over POTS. available only on the Cisco 880G models Cisco 880 Series Data Routers.SHDSL. 802.3af-compliant devices connected to ethernet ports 0 and 1. DSL Multi-mode (VDSL/ADSLoPOTS.1 port Express card slot for third-generation (3G) cellular data WAN connectivity.SHDSL port for connecting to the WAN Optional embedded Wi-Fi CERTIFIED™. 802. ADSL over ISDN. or G. and backup capabilities. VDSLoPOTS. you must order and install it to enable the PoE function. page 1-9 Cisco 880 Series with Embedded WLAN Antennas. VDSL/ADSL over ISDN. page 1-6 Cisco 880 Series Voice and Data Routers. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-6 OL-16215-10 . They have the following features: • • Integrated 4-port 10/100 Ethernet switch for connecting to the LAN 10/100 FE. VDSL/ADSLoISDN Cisco VA models only). See the Cisco 880 Series Integrated Services Routers data sheet for the WAN interface that is supported on your router. 3G. page 1-15 The following features are located on the front panel: • • This section contains the following topics: • • • Cisco 880 Series Data Routers The Cisco 880 series data routers provide integrated VPN. VDSL/ADSL over POTS.

BRI = Basic rate interface. Ports 0 and 1 provide PoE with the optional PoE module installed. Figure 1-7 shows the back panel details of the Cisco 886VA data router. Figure 1-7 Back Panel of the Cisco 886VA Router 1 2 3 4 5 6 7 8 9 1 2 3 4 5 Data BRI1 0 Primary WAN port—VDSL/ADSL over ISDN 4-port 10/100 Ethernet switch2 Serial port—console or auxiliary PoE power connector—optional 6 7 8 9 Reset button Power connector Earth ground connection Kensington security slot 1. Caution The primary WAN port is designed for an RJ-45 connector only.Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-6 Front Panel of the Cisco 880 Series Wireless Data Router 1 2 3 1 2 LEDs 3G express card slot—Supports third-party 3G card (Cisco 880G models only) 1 3 USB port 1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-7 254090 231950 . Cisco 880 Series. Damage to the primary WAN port may occur if a non-RJ-45 connector is inserted. Cisco 860 Series. 2.

Figure 1-9 shows the back panel details of the Cisco 888W data router. Figure 1-9 Back Panel of the Cisco 888W Data Router 1 2 3 4 5 6 7 8 9 10 Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-8 OL-16215-10 231951 254139 . Figure 1-8 Back Panel of the Cisco 887VA and 887VA-M Router 1 2 3 4 5 6 7 8 1 2 3 4 Primary WAN port—VDSL/ADSL over POTS1 4-port 10/100 Ethernet switch2 Serial port—console or auxiliary PoE power connector—optional 5 6 7 8 Reset button Power connector Earth ground connection Kensington security slot 1. Cisco 880 Series. However. Ports 0 and 1 provide PoE with the optional PoE module installed. the feature locations are similar across all Cisco 880 series data routers. 887VA-M has Annex M support. Damage to the primary WAN port may occur if a non-RJ-45 connector is inserted. the primary WAN port is designed for an RJ-45 connector only. Caution For the Cisco 887VA. Nonwireless routers do not have antennas on the back panel.Chapter 1 Cisco 880 Series ISRs Product Overview Figure 1-8 shows the back panel details of the Cisco 887VA and 886VA-M data router. 2.

or 10/100 FE. Cisco 881 SRST and Cisco 888 SRST Figure 1-10. The features available vary. Cisco 860 Series. the primary WAN port can be either G. The VDSLoPOTS port is in the same location as the G. Figure 1-11. Some features may not be available on your router. See Figure 1-2 for the location of the 10/100 FE WAN port. and Figure 1-12 show the features available on the Cisco 881 SRST and Cisco 888 SRST routers. ADSLoISDN. Foreign Exchange Office (FXO). or BRI connections.SHDSL or 10/100 FE. or 10/100 FE Antenna—captive omnidirectional dipole WLAN antenna (wireless models only) 4-port 10/100 Ethernet switch Serial port—console or auxiliary 6 7 PoE power connector for optional PoE module1 Reset button 3 4 5 8 9 Power connector Earth ground connection 10 Kensington security slot 1.SHDSL. 2. VDSLoPOTS. The voice ports managed voice services that interface with Foreign Exchange Station (FXS). If this feature was not configured with the factory order. Cisco 880 Series Voice and Data Routers The Cisco 880 series voice and data routers provide both voice and data ports. depending on the router model. Depending on the router model. ADSLoPOTS. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802. VDSLoPOTS. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-9 . See the Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are supported on your router.3af-compliant devices connected to ethernet ports 0 and 1. the primary WAN port can be G. Depending on the router model. you must order and install it to enable the PoE function. The 10/100 FE WAN port is located at the bottom left corner.SHDSL port.SHDSL.Chapter 1 Product Overview Cisco 880 Series ISRs 1 2 ISDN port—not available on 3G models Primary WAN port2—G. Cisco 880 Series.

Cisco 880 Series. Figure 1-10 Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router 1 2 1 LEDs 2 USB port Cisco 860 Series.Chapter 1 Cisco 880 Series ISRs Product Overview Figure 1-10 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-10 OL-16215-10 270495 .

3af-compliant devices connected to ethernet ports 0 and 1. 2. 7. 3. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-11 241904 . TBP = trunk bypass. 4. one FXO4 port with TBP5 power failover 4-port 10/100 Ethernet switch6 Serial port—console or auxiliary PoE power connector for optional PoE module7 6 7 8 9 Antenna—captive wireless omnidirectional dipole WLAN antenna (wireless models only) Reset button Power connector Earth ground connection 10 Kensington security slot 1. The PoE power supply. Cisco 860 Series.Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-11 shows the back panel details of the Cisco 881SRST-W voice router. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802. SKU 800-IL-PM-2. If this feature was not configured with the factory order. Figure 1-11 Back Panel of the Cisco C881SRST-W Voice Router 6 1 2 2 3 4 5 7 8 9 10 1 2 3 4 5 Primary WAN port1—10/100 FE Voice ports—four FXS2/DID3 ports. you must order and install it to enable the PoE function. 5.SHDL or 10/100 FE. 6. the primary WAN port can be either G. is also required. DID = Direct Inward Dialing. Cisco 880 Series. Ports 0 and 1 provide PoE with the optional PoE module installed. FXO = Foreign Exchange Office. Depending on the router model. FXS = Foreign Exchange Station. SKU 800-ILPM-4.

you must order and install it to enable the PoE function. Caution The primary WAN port on all 888E models is designed for an RJ-45 connector only. the primary WAN port can be either G. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802. is also required.Chapter 1 Cisco 880 Series ISRs Product Overview Figure 1-12 shows the back panel details of the Cisco 888SRST-W voice router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-12 OL-16215-10 241905 . 3. Damage to the primary WAN port may occur if a non-RJ-45 connector is inserted. 2. Figure 1-12 Back Panel of the Cisco C888SRST-W Voice Router 2 1 2 6 3 4 5 7 8 9 10 1 2 3 4 5 Primary WAN port1—G. Depending on the router model.SHDSL Voice ports—four FXS/DIDports and one voice BRI port 4-port 10/100 Ethernet switch2 Serial port—console or auxiliary PoE power connector for optional PoE module3 6 7 8 9 Antenna—captive wireless omnidirectional dipole WLAN antenna (wireless models only) Reset button Power connector Earth ground connection 10 Kensington security slot 1. Cisco 880 Series. If this feature was not configured with the factory order.3af-compliant devices connected to ethernet ports 0 and 1.SHDL or 10/100 FE. SKU 800-IL-PM-2. Cisco 860 Series. The PoE power supply. SKU 800-ILPM-4. Ports 0 and 1 provide PoE with the optional PoE module installed.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-13 246861 .Chapter 1 Product Overview Cisco 880 Series ISRs Cisco 881-V. and Cisco 887VA-V-W Figure 1-13. Table 1-3 lists the maximum number of calls that is supported when the codec complexity command is configured for Flexible. Note Configuring the codec complexity setting to support secure calls uses DSP resources. and Cisco 887VA-V-W Routers 1 2 1 LEDs 2 USB port Cisco 860 Series. Some features may not be available on your router. Figure 1-14. Cisco 887VA-V. and Cisco 887VA-V-W. Cisco 887VA-V. but does not affect the maximum number of supported calls. Medium or High complexity. The features available vary. Cisco 887VA-V. depending on the router model. However. Figure 1-13 Front Panel of the Cisco 881-V. Cisco 880 Series. The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS or BRI voice ports. and Figure 1-15 show the features available on the Cisco 881-V and Cisco 887VA-V routers. Table 1-3 Maximum Number of Supported Calls Flexible Complexity C881-V C887VA-V C887VA-V-W 9 8 8 Medium Complexity 8 8 8 High Complexity 6 6 6 Figure 1-13 shows the front panel details of the Cisco 881-V. the number of concurrent calls that can be supported by the router is limited by the codec complexity setting on the router.

The Cisco 887VA-V (non-wireless) router does not have the antennas on the back panel. Figure 1-14 Back Panel of the Cisco 887 VA-V Router 11 VD SL/ D SL A overPO TS C 887VA -W VO I E C 6 5 4 3 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 Data BRI Voice BRI Voice ports—four FXS/DID ports Fast Ethernet LAN—four ports Console Port PoE power connector (optional) 7 8 9 Reset Button Power connector Earth ground connection 10 Kensington security slot 11 Primary WAN port—VDSL/ADSL over POTS Figure 1-15 shows the back panel for the Cisco 881-V router.Chapter 1 Cisco 880 Series ISRs Product Overview Figure 1-14 shows the back panel for the Cisco 887VA-V-W router. Figure 1-15 Back Panel of the Cisco 881-V Router C881 VOI CE 6 5 4 3 7 1 2 3 4 5 6 7 8 9 10 Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-14 OL-16215-10 246866 246864 . Cisco 880 Series.

11b/g/n-compliant wireless AP. Cisco 880 Series. 802. Figure 1-16 Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs OK PPP 0 1 CD DATA LINK 2. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-15 284983 . The front panel has LEDs only. and 880-WD ISRs have three embedded WLAN antennas. All the ports are in the back panel. Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a 60-W power supply for POE-enabled routers. see Cisco 880 Series Integrated Services Router Software Configuration Guide. Cisco 887VA-WD Figure 1-16 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. 880WD.4 GHz and 5 GHz) WLAN cards. embedded Wi-Fi CERTIFIED™. Have a fixed 512 MB of system memory. and backup capabilities.Chapter 1 Product Overview Cisco 880 Series ISRs 1 2 3 4 5 Fast Ethernet WAN port Voice BRI ports Voice ports—four FXS/DID ports and one FXO port.4GHz 5GHz POE FE LAN xDSL WLAN Cisco 800 Series VPN 0 1 2 3 Cisco 860 Series. These ISRs are fixed-platform routers that: • • • • Provide integrated VPN. For information on configuring the Cisco 880 series ISRs.4 GHz) WLAN cards or dual-band (2. Use single-band (2. Fast Ethernet LAN—four ports Console Port 6 7 8 9 PoE power connector (optional) Reset button Power connector Earth ground connection 10 Kensington security slot Cisco 880 Series with Embedded WLAN Antennas Some Cisco 880W.

All the ports are in the back panel. 5 Reset button C881WD Figure 1-18 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. Cisco 880 Series. Figure 1-18 Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs OK PPP 0 1 FE4 LINK 2. For information on system power supply requirements when PoE is enabled. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-16 OL-16215-10 284982 284988 overPOTS Cisco 887VA-WD FE LAN CONSOLE O POE OPTION REQUIRES 5A POWER ADAPTOR . see the “Power over Ethernet Module” section on page 1-38.4GHz 5GHz POE FE LAN WAN WLAN Cisco 800 Series VPN 0 1 2 3 Cisco 860 Series. The front panel has LEDs only. Figure 1-17 Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs 9 8 0 RESET 12VDC 5A 3 2 1 0 AUX 1 2 3 4 5 6 7 1 2 3 4 USB port 4-port 10/100 Ethernet switch Serial port—console or auxiliary Note 6 7 8 Power connector Kensington security slot Power switch VDSL/ADSL port No separate PoE power supply is 9 required for routers with embedded WLAN antennas.Chapter 1 Cisco 880 Series ISRs Product Overview Figure 1-17 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.

11a/b/g/n-compliant wireless AP Optional 4-port PoE Note The Cisco 890 series ISRs can include an optional PoE module that provides power to 802. see the “Power over Ethernet Module” section on page 1-38. If this feature was not configured with the factory order. Cisco 860 Series.3af-compliant devices connected to ethernet ports 0 through 3. Cisco 892. Figure 1-19 Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs 9 Cisco 881WD FE WAN FE LAN CONSOLE O RESET 12VDC 5A 4 0 3 2 1 0 AUX 1 2 3 4 5 6 7 8 1 2 3 4 5 Primary WAN port—10/100 FE USB port 4-port 10/100 Ethernet switch Serial port—console or auxiliary Note 6 7 8 9 Reset button Power connector Kensington security slot Power switch No separate PoE power supply is required for routers with embedded WLAN antennas. and Cisco 892F ISRs have the following features: • • • • • Integrated 8-port 10/100 Ethernet switch for connecting to the LAN 10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN Separate console and auxiliary ports Optional embedded Wi-Fi CERTIFIED™ dual radio 802. and Cisco 892F The Cisco 891. Cisco 890 Series ISRs Cisco 891. For information on system power supply requirements when PoE is enabled. Cisco 892. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-17 284987 POE OPTION REQUIRES 5A POWER ADAPTOR . you must order and install it to enable the PoE function.Chapter 1 Product Overview Cisco 890 Series ISRs Figure 1-19 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. Cisco 880 Series.

Chapter 1 Cisco 890 Series ISRs Product Overview • • Security feature card (SFC) socket DIMM expansion socket that can accept up to 512 MB of additional memory. and a total of 1 GB system memory in Cisco 892F series ISRs Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for non-captive dual-band WLAN antenna (wireless models only) Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9 GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only) Two USB 1. for a total of 768 MB system memory in Cisco 891 and 892 series ISRs.1 ports • • • The following feature is located on the front panel: • Figure 1-20 shows the front panel details of the Cisco 890 wireless router. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-18 OL-16215-10 272367 . Figure 1-20 Front Panel of the Cisco 890 Series Wireless ISR 1 2 1 LEDs 2 USB ports Cisco 860 Series.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-19 272369 . The Cisco 890 series ISRs can include an optional PoE module that provides power to 802. The V.Chapter 1 Product Overview Cisco 890 Series ISRs Figure 1-21 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have RP-TNC antennas or connectors on the back panel. Cisco 880 Series. However.92 port (not shown) is available only on the Cisco 891 router models and is located between the console port and the Ethernet switch. 2. Some of the features that are shown may not be available on your router. the feature locations are similar across all Cisco 890 series routers. 3.3af-compliant devices connected to ethernet ports 0 through 3. Cisco 860 Series. If this feature was not configured with the factory order you must order and install it to enable the PoE function. Figure 1-21 Back Panel of the Cisco 892-W Router 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 Antenna—dipole swivel antenna attached to RP-TNC connectors (wireless models only) Backup—Data BRI2 or V. The Data BRI port is available only on the Cisco 892 router models.923 port Primary WAN port—FE and GE Auxiliary port Console port 8-port 10/100 Ethernet switch 7 8 9 PoE power connector for optional PoE module1 Reset button Power connector 10 Earth ground connection 11 Kensington security slot 1.

897VA (897VA.Chapter 1 Cisco 890 Series ISRs Product Overview Figure 1-22 shows the location of the SFP port in a Cisco 892F-W router. 897VA. 897VA. 896VA. 897VAW. 897VAMW). and Cisco 898EA The Cisco 892FSP. and 898EA routers have the following features: • • • • • • • • Integrated 8-port 10/100/1000 Gigabit Ethernet(GE) switch for connecting to the LAN Two 10/100/1000 GE ports for the Cisco 892FSP One 10/100/1000 GE port for the Cisco 896VA. Cisco 880 Series. Cisco 897VA. Note The Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have an SFC socket. and the Cisco 898EA.0 port Optional internal adapter for inline PoE on 4 switch ports for IP phones or external wireless access points for Cisco 896VA. 897VAM. Cisco 896VA. No PoE support on Cisco 892FSP. and Cisco 898EA One USB 2. Single console and auxiliary ports for configuration and management 512 MB of on-board memory (upgrade option to 1 GB) 256 MB flash memory for the Cisco 896VA. but not both. Either the SFP socket or the 10/100/1000 GE port can be active at a given time. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-20 OL-16215-10 278179 EN . 897VA. Figure 1-22 SFP Port Location in a Cisco 892F-W Router Cisco 892F-W SFP S 1 2 1 SFP port 2 SFP LEDs Cisco 892FSP. Cisco 860 Series. and 898EA models only.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-21 284782 284781 .Chapter 1 Product Overview Cisco 890 Series ISRs Figure 1-23 shows the back panel of the Cisco 892FSP router. Figure 1-24 Front Panel of the Cisco 892FSP Router 1 1 LEDs Cisco 860 Series. Figure 1-23 Back Panel of the Cisco 892FSP Router C i 892FSP sco GE W AN GE W AN SFP C O N SO LE RESE T 9 8 8 AU X 12VD C 2. Cisco 880 Series. 5A 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 GE WAN interface SFP port USB port 8-port Gigabit Ethernet switch Console / Auxiliary port 6 7 8 9 Power connector On/Off switch Reset button Earth ground connection 10 Kensington security slot Figure 1-24 shows the front panel of the Cisco 892FSP router.

If this feature was not configured with the factory order. Figure 1-26 Front Panel of the Cisco 896VA and Cisco 897VA Router 1 1 LEDs Cisco 860 Series.2A 2. Cisco 880 Series.Chapter 1 Cisco 890 Series ISRs Product Overview Figure 1-25 shows the back panel of the Cisco 896VA router. POE is an optional feature for this model. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-22 OL-16215-10 344765 344766 . you must order and install it to enable the PoE function. Port 0 through 3 can be configured as POE. Figure 1-25 Back Panel of the Cisco 896VA Router 12 7 6 GELAN 5 4 Cisco 896VA CONSOLE VDSL/ADSL overISDN GE WAN ISDN 0 8 3 2 POE 1 0 54VDC 12VDC 1.5A RESET 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 ISDN GE WAN interface SFP port USB port 8-port Gigabit Ethernet switch1 Console / Auxiliary port 7 8 9 Power connector On/Off switch Reset button 10 Earth ground connection 11 Kensington security slot 12 VDSL / ADSL over ISDN 1. Figure 1-26 shows the front panel of the Cisco 896VA and the Cisco 897VA router.

2A 2. POE is an optional feature for this model. Cisco 880 Series. Port 0 through 3 can be configured as POE. you must order and install it to enable the PoE function. Figure 1-27 Back Panel of the Cisco 897VA Router 12 Cisco 897VA CONSOLE VDSL/ADSL overPOTS GE WAN 7 6 GELAN 5 4 ISDN 0 8 3 2 POE 1 0 54VDC 12VDC 1.5A RESET 1 2 3 4 5 6 7 8 9 10 1 2 3 GE WAN interface SFP port USB port 7 8 9 On/Off switch Reset button Earth ground connection Cisco 860 Series. Figure 1-28 shows the back panel of the Cisco 897VAM router.5A RESET 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 ISDN GE WAN interface SFP port USB port 8-port Gigabit Ethernet switch Console / Auxiliary port 1 7 8 9 Power connector On/Off switch Reset button 10 Earth ground connection 11 Kensington security slot 12 VDSL / ADSL over POTS 1.Chapter 1 Product Overview Cisco 890 Series ISRs Figure 1-27 shows the back panel of the Cisco 897VA router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-23 344769 344767 . Figure 1-28 Back Panel of the Cisco 897VAM Router 11 VDSL/ADSL overPOTS GE WAN 7 6 GELAN 5 4 CONSOLE 8 3 2 POE 1 0 54VDC 12VDC 1. If this feature was not configured with the factory order.2A 2.

Chapter 1 Cisco 890 Series ISRs Product Overview 4 5 6 8-port Gigabit Ethernet switch1 Console / Auxiliary port Power connector 10 Kensington security slot 11 VDSL / ADSL over POTS 1. If this feature was not configured with the factory order. Figure 1-30 Back Panel of the Cisco 897VAW Router 11 VDSL/ADSL overPOTS GE WAN 7 6 GELAN 5 4 CONSOLE 8 3 2 POE 1 0 54VDC 12VDC 1. you must order and install it to enable the PoE function.5A RESET 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 GE WAN interface SFP port USB port 8-port Gigabit Ethernet switch Console / Auxiliary port Power connector 1 7 8 9 On/Off switch Reset button Earth ground connection 10 Kensington security slot 11 VDSL / ADSL over POTS Cisco 860 Series.2A 2. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. Cisco 880 Series. Figure 1-29 shows the front panel of the Cisco 897VAM router. Figure 1-29 Front Panel of the Cisco 897VAM Router 1 1 LEDs Figure 1-30 shows the back panel of the Cisco 897VAW router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-24 OL-16215-10 344771 344768 .

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-25 344772 344770 . Cisco 860 Series. Port 0 through 3 can be configured as POE. If this feature was not configured with the factory order. POE is an optional feature for this model. Port 0 through 3 can be configured as POE.2A 2. you must order and install it to enable the PoE function. If this feature was not configured with the factory order.5A RESET 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 GE WAN interface SFP port USB port 8-port Gigabit Ethernet switch1 Console / Auxiliary port Power connector 7 8 9 On/Off switch Reset button Earth ground connection 10 Kensington security slot 11 VDSL / ADSL over POTS 1. Cisco 880 Series. Figure 1-31 Front Panel of the Cisco 897VAW and the Cisco 897VAMW Router 1 1 LEDs Figure 1-32 shows the back panel of the Cisco 897VAMW router. Figure 1-32 Back Panel of the Cisco 897VAMW Router 11 VDSL/ADSL overPOTS GE WAN 7 6 GELAN 5 4 CONSOLE 8 3 2 POE 1 0 54VDC 12VDC 1. POE is an optional feature for this model. Figure 1-31 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW router. you must order and install it to enable the PoE function.Chapter 1 Product Overview Cisco 890 Series ISRs 1.

If this feature was not configured with the factory order. Cisco 880 Series.2A 2. Figure 1-34 Front Panel of the Cisco 898EA Router 1 1 LEDs Cisco 860 Series. Port 0 through 3 can be configured as POE. Damage to the primary WAN port may occur if a non-RJ-45 connector is inserted. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-26 OL-16215-10 344773 344774 . Caution The primary WAN port is designed for an RJ-45 connector only. Figure 1-34 shows the front panel of the Cisco 898EA router. Figure 1-33 Back Panel of the Cisco 898EA Router 11 RJ45 ONLY 7 6 GELAN 5 4 Cisco 898EA CONSOLE SHDSL GE WAN SFP 8 8 3 2 POE 1 0 AUX 54VDC 12VDC 1.5A RESET 1 1 2 3 4 5 6 GE WAN interface SFP port USB port 2 3 7 8 9 1 4 5 6 7 8 9 10 On/Off switch Reset button Earth ground connection 8-port Gigabit Ethernet switch Console / Auxiliary port Power connector 10 Kensington security slot 11 SHDSL (RJ45 Only) 1.Chapter 1 Cisco 890 Series ISRs Product Overview Figure 1-33 shows the back panel of the Cisco 898EA router. you must order and install it to enable the PoE function. POE is an optional feature for this model.

Cisco 880 Series. Cisco 860 Series. the reset button can be used to load a custom configuration file without having to use the CLI. and 890 series ISRs. or by pressing the Reset button for 5 seconds while running IOS. by pressing the Reset button within 5 seconds of powering up the router. Note If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified IOS software. To secure the router to a desktop or other surface.Chapter 1 Product Overview Hardware Features Hardware Features This section provides an overview of the following hardware features for the Cisco 860 series. Cisco 860VAE Routers—Custom Configuration File On Cisco 860VAE routers. the router reboots. 880 series. Reset Button The Reset button is used to restore the router to the factory default configurationor to load a custom configuration file. 2. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-27 . • • • • • • • • • • • Kensington Lock Reset Button LEDs Memory USB Port Fan Power over Ethernet Module 3G Cellular Data WAN Connectivity Wireless LAN Connectivity Small Form-Factor Pluggable Port Feature Summary Kensington Lock A Kensington security slot is located on the router back panel. but the AP continues running. use the Kensington lockdown equipment. A feature summary is available at the end of this section. Clients with Cisco Unified IOS software are controlled by a wireless LAN controller (WLC) and can be reset only by the controller. The configuration file can be located on an external USB flash drive or on the router's compact flash. There are two different ways to do this: 1.

nvram: *. The custom configuration file must use cfg as the filename extension. The router reloads itself after the startup configuration has been replaced with the new customer configuration. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-28 OL-16215-10 . this occurs within 5 seconds. Cisco 880 Series. 4. the system aborts the process. 3.Chapter 1 Hardware Features Product Overview The custom configuration file must be named one of the following: • • customer-config SN-customer-config where “SN” is the unique hardware serial number. follow these steps: Step 1 Step 2 Verify that IOS is running correctly by checking that the system status LED is on. Typically. To reset the router to the factory default configuration. 2. the configuration file can be located on the router's compact flash or on the router's nvram. the system aborts the process. The priority for loading a configuration file is as follows: 1. Custom Configuration File for Cisco 892FSP.cfg Router flash: *. When the system attempts to load a custom configuration file. configuration files on nvram have priority over configuration files on the router's compact flash. 2. configuration files on a USB flash drive have priority over configuration files on the router's flash drive and the “SN-customer-config” file name has priority over the “customer-config” file name. Cisco 860 Series. and Cisco 898EA For the first method. When the system attempts to load a custom configuration file. Press and hold the Reset button until the system status LED begins to flash. The priority for loading a configuration file is as follows: 1. USB flash0: SN-customer-config USB flash0: customer-config Router flash: SN-customer-config Router flash: customer-config If the router does not find a valid custom configuration file.cfg If the router does not find a valid custom configuration file. 897VA. 896VA.

Press and hold the Reset button until the system status LED begins to flash. For the second method. The priority for loading a configuration file is as follows: 1. 3. this occurs within 5 seconds. this occurs within 5 seconds. 4.SN usbflash0:customer-config Router flash:customer-config. To reset the router to the factory default configuration or to load a custom configuration file. The router reloads itself after the startup configuration has been replaced with the new customer configuration. Cisco 880 Series.SN" file name has priority over the customer-config file name. the system aborts the process. Typically. Cisco 860 Series. When the system attempts to load a custom configuration file.SN ? where "SN" is the unique hardware serial number. Typically. The router reloads itself after the startup configuration has been replaced with the new customer configuration. follow these steps: Step 1 Step 2 Verify that IOS is running correctly by checking that the system status LED is on. usbflash0:customer-config.Chapter 1 Product Overview Hardware Features To reset the router to the factory default configuration or to load a custom configuration file. 2. configuration files on a USB flash drive have priority over configuration files on the router's flash drive and the "customer-config. follow these steps: Step 1 Step 2 Turn the power on. Press and hold the Reset button until the system status LED begins to flash.SN Router flash:customer-config If the router does not find a valid custom configuration file. the configuration file can be located on an external USB flash drive or on the router's compact flash. The custom configuration file must be named one of the following: • • customer-config customer-config. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-29 .

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-30 OL-16215-10 . Cisco 880 Series. Cisco 866VAE-K9. Blinking—Data is either being received or being transmitted. — — All models WLAN (2. Blinking—Data is either being received or being transmitted. and Cisco 890 Series ISRs LED Power OK Color Green Description On—DC power is being supplied to the router and the Cisco IOS software is running. SSID1 is configured. and 890 series ISRs. Off—Port is not connected. SSID is configured. Table 1-6 lists the LED description for the Cisco 892FSP ISR. • • • Table 1-4 Table 1-4 describes the LEDs for the Cisco 860 series. and client Wireless models is associated. Fast blinking—Data is either being received or being transmitted.Chapter 1 Hardware Features Product Overview LEDs The LEDs are located on the front panel of the router. 897VA. or the router is in Rommon monitor mode. Off—Port is not connected. All models All models All models Green On—Ethernet port is connected.4 GHz) Green On—Radio is connected. 896VA. Off—Ethernet port is not connected. LED Descriptions for the Cisco 860 Series. Off—Radio is shut down. Table 1-5 lists the LED descriptions for the Cisco 866VAE. 861 models 881 models All models GE WAN Port Link Status Green On—Port is connected. 880 series. and no SSID is configured. Off—Power is not supplied to the router. Wireless models Wireless models Cisco 860 Series. and 898EA. Slow blinking—Radio is connected. Blinking—Bootup is in process. Cisco 867VAE. Cisco 880 Series. — — All models Green On—Port is connected. Blinking—Data is either being received or being transmitted. but no data is being received or being transmitted. and beacons are being transmitted. Blinking—Data is either being received or being transmitted. Off—Ethernet port is not connected. and Cisco 867VAE-K9 ISRs. 860 Series 880 Series 890 Series All models All models All models Link Status FE0 Link Status FE1 Link Status FE2 Link Status FE3 Link Status FE4 Link Status FE5 Link Status FE6 Link Status FE7 FE WAN Port Link Status Green On—Ethernet port is connected.

and client is — associated. Cisco 880 Series. On—ISDN D channel is connected. Blinking—Ethernet link is up. 897VA.Chapter 1 Product Overview Hardware Features Table 1-4 LED Descriptions for the Cisco 860 Series. Fast blinking—Data is either being received or being transmitted. and data is either being received or being transmitted. — xDSL ATM xDSL EFM Data BRI LINK Data BRI B1 Green Green Green Green On—The router is operating in ATM6 mode. 888 models — 898EA 892 models 892 models xDSL CD xDSL Data Green Blinking—The xDSL interface is either receiving or transmitting data. and no SSID is configured. but no data is being received or being transmitted. WLAN LINK (Autonomous Mode) Green On—Wireless link is up. On—VPN is connected. Off—No data is being transmitted or being received. — or data is passing through ISDN channel 1. Wireless models Wireless models PoE Green Amber On—PoE is connected and powered. and Cisco 890 Series ISRs (continued) LED WLAN (5 GHz) Color Green Description 860 Series 880 Series Wireless models 890 Series Wireless models On—Radio is connected. Blinking—Training to the line. 5 — Models with PoE Models with PoE VPN PPP 3 4 Green Green Green — — — All models All models All models All models 887. Off—Not operating in EFM mode. Slow blinking—Radio is connected. SSID is configured. On—The xDSL interface is connected to the DSLAM . Off—Wireless link is down. but wireless AP is not communicating with LWAPP controller. 896VA. Blinking—Ethernet link is up. 896VA. Blink—The router is operating in EFM7 mode. 887VA-M8 898EA 88 models 888E — 887. Off—Ethernet link is down. Wireless models Wireless models Wireless models WLAN LINK (Unified Mode) Green On—Ethernet link is up. Off—Not operating in ATM mode. — — — Blinking—B1 channel is either receiving or sending data. Off—Indicates that a connection has not been established or the port is shut down. Off—PoE is not installed. On—Fault with the PoE. 887VA-M8 898EA 888 models 887. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-31 . 888 models 887. 887VA. Off—Radio is shut down. 887VA. Cisco 880 Series. 897VA. Cisco 860 Series. SSID is configured. and wireless access point (AP) is — communicating with LWAPP2 controller. and beacons are being transmitted. On—At least one PPP session is established.

— SRST models — — V. Present with failure. — — — — — — BRI Voice B2 Green On—BRI B2 channel is connected. Blinking—FXO port is either receiving or transmitting data. On—Service is established. — 891 models 892F models SFP14 EN Off Green Amber Not present. SSID = service set identifier. On—FXO port is connected. Cisco 880 Series. Fast Blinking—Medium RSSI (-89 to -70 dBm). — — — FXS/DID Voice Green On—FXS/DID port is connected.Chapter 1 Hardware Features Product Overview Table 1-4 LED Descriptions for the Cisco 860 Series. or data is passing through ISDN channel 2. On—BRI B1 channel is connected. — — — — 3G models — 3G models — 3G models — 88113 — Green 12 3G CDMA Green Green FXO Voice BRI Voice LNK BRI Voice B1 Green Green On—BRI interface is connected. 887V.92 port is either receiving or transmitting data. Blinking—Blinking frequency indicates port speed. Fast Blinking—Data is either being received or being transmitted. Slow Blinking—Low or medium RSSI (-99 to -90 dBm). On—Service is established. Off—No service. Blinking—BRI B2 channel is either receiving or transmitting data. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-32 OL-16215-10 . Blinking—FXS/DID port is either receiving or transmitting data. 860 Series — 880 Series 890 Series 887. Blinking—V. Cisco 860 Series. Present and enabled. — 3G models — Amber 3G GSM 11 On—No service. and Cisco 890 Series ISRs (continued) LED Data BRI B2 Color Green Description Blinking—B2 channel is receiving or sending data. Slow Blinking—Searching for service. On—Service is established. Cisco 880 Series. Off—No service. — — — — — — — — SFP S Green 892F models 1.92 Modem Green On—Modem is connected. On—High RSSI (-69 dBm or higher). 892 888 models models 3G models — 3G8 WWAN9 Green — 3G RSSI10 Green Off—Low signal strength (lower than -100 dBm). Blinking—BRI B1 channel is either receiving or transmitting data.

RSSI = Received Signal Strength Indicator. such as in-training. Cisco 867VAE. 4. Cisco 860 Series. and Cisco 867VAE-K9 ISRs LED Power/System Activity Description Power/System LED: Solid Power is on and system running in the Rommon mode. Power/System LED: Solid IOS functioning in GE WAN mode. 13. GE_MODE LED: Solid DSL_LINK LED: Off Power/System LED: Solid IOS functioning in DSL_WAN mode. Cisco 880 Series.” or no cable attached to DSL connector. ATM = Asynchronous Transfer Mode. CDMA = code division multiple access. Cisco 866VAE-K9. 14. DSL_LINK LED will be solid after DSL DSL_LINK LED: Solid or training complete or flashing during training. SFP = small-form-factor pluggable. 3. 10. xDSL = General term referring to various forms of DSL. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-33 . EFM = Ethernet in the First Mile. 8. Cisco 866VAE-K9. DSL_LINK and GE_MODE LED will be turned off later after booting into Rommon. Cisco 867VAE. LWAPP = Lightweight Access Point Protocol. WWAN = wireless WAN. Off—Device is powered off or GE WAN mode is selected. 5. 9. GSM = Global System for Mobile Communication. 11. Faster blinking—Heavier traffic Off—Device is powered off or the DSL WAN interface is down. including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line). both Power/System. or controller “OFF. SRST = Survivable Remote Site Telephony. DSLAM = digital subscriber line access multiplexer. PPP = Point-to-Point Protocol. flashing xDSL1 ACT Green On—DSL interface is up. Table 1-5 LED Descriptions for the Cisco 866VAE. 3G = Third-Generation. GE_MODE LED: Off Note During the early booting stage. and Cisco 867VAE-K9 ISRs. Blinking—DSL WAN activity (traffic in either direction). GE_MODE LED: Off Note In IOS DSL_WAN mode. GE_MODE and DSL_LINK LED: Off DSL_LINK LED will be turned on temporarily for the power on test. 7. Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state. 6.Chapter 1 Product Overview Hardware Features 2. Table 1-5 describes the LEDs for the Cisco 866VAE. 12. xDSL Link Green On—DSL WAN Mode is selected and DSL training complete.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-34 OL-16215-10 . Cisco 866VAE-K9.Chapter 1 Hardware Features Product Overview Table 1-5 LED Descriptions for the Cisco 866VAE. including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line). Cisco 880 Series. Blinking—GE WAN activity (traffic in either direction). 1. Cisco 867VAE. Cisco 860 Series. xDSL = General term referring to various forms of DSL. and Cisco 867VAE-K9 ISRs LED GE ACT Activity Green Description On—GE WAN interface is up. Off—Device is powered off or GE WAN interface is down. GE Mode Green On—GE WAN Mode is selected. Off—Device is powered off or DSL WAN mode is selected.

Chapter 1 Product Overview Hardware Features Table 1-6 describes the LEDs for the Cisco 892FSP. Off—No PPP session. BRI2 and the FXS ports share LED indicators. Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers On the Cisco 881-V. and Cisco 887VA-V-W routers. Blinking—Data is either being received or being transmitted. Cisco 880 Series. Steady on—At least one tunnel is up. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-35 . VPN_OK PPP_OK Green Green — — Off—No tunnel. Green/Amber Blinking—Data is either being received or being transmitted. Blinking—Data is either being received or being transmitted. Off—No link. 896VA. Cisco 887VA-V. 897VA. Off—No link. GE0 GE1 GE2 GE3 GE4 Green/Amber Link Status Green On—Ethernet port is connected. GE WAN ports Green Link Status On—Port is connected. and 898EA Routers LED PWR_OK Color Green Activity Power Status Description Off—No power. Steady on—At least one PPP established. Blinking—Data is either being received or being transmitted. Green/Amber Off—Ethernet port is not connected. The following ports share an LED indicator: • • • • BRI 1B1 channel and FXS 3 BRI 1B2 channel and FSX 4 BRI 2B1 channel and FXS 5 BRI 2 B2 channel and FXS 6 Cisco 860 Series. GE5 GE6 GE7 Green Link Status On—Ethernet port is connected. the BRI1. Steady on—Normal operation. SFP WAN ports Green Link Status On—Port is connected. Amber On—Fault with PoE. There is a fault with the inline power supply. Blink—Boot up phase or in ROM Monitor mode. Table 1-6 LED desciption for Cisco 892FSP ISR. Off—Ethernet port is not connected.

and a separate non-volatile flash contains the cookie configuration. use the show port summary command. the boot flash contains the ROMMON boot code. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-36 OL-16215-10 300149 . For activity status on the BRI ISDN port. 880 series. Cisco 880 Series. Table 1-7 describes the default flash memory storage. use the show isdn status command. You can determine the activity status on each interface by using the following commands. and 890 series ISRs use non-upgradable flash memory storage. 128 MB for IOS 64 MB boot flash and IOS Cisco 880 series voice routers and Cisco 890 series routers 256 MB Cisco 860 Series. the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or when the FXS port is active. Figure 1-35 Close-up of the BRI and FXS LED Indicators Memory The Cisco 860 series. Table 1-7 Flash Memory Storage Models Cisco 860 series and 880 series routers Cisco 880 series routers with embedded WLAN antennas Cisco 860VAE routers Cisco 860VAE-K9 Flash Memory Storage 128 MB 256 MB 8 MB boot flash. 880 series. and 890 series routers contain flash memory and main memory. Figure 1-35 shows a close-up view of the LED indicators. the LED illuminates (green) when either port is active. For example.Chapter 1 Hardware Features Product Overview Because the LED indicators are shared. • • For activity status on the FXS ports. The onboard flash memory contains the Cisco IOS software image. Flash Memory The Cisco 860 series.

0-compliant port located on the back panel. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-37 . as a diagnostic aid. 897VA. Cisco897VA. for a maximum of 768 MB. Except for Cisco 892FSP. while other models have either one or two fans. 898EA routers 512 MB USB Port Table 1-9 describes the USB ports for different router models. 256-MB or 512-MB double data rate 2 (DDR2) SODIMM. After the router has booted. Cisco 860 Series. Fan Some router models do not have a fan. The USB port provides connection for USB devices such as security tokens and flash memory. One USB 1.0-compliant ports located on the front panel. Table 1-8 Main Onboard Memory Storage Models Cisco 860 series routers Cisco 880 series routers Onboard Memory Storage 256 MB 256 MB (expandable to 768 MB) Expandability Not expandable. Cisco 890 series1 Cisco 892FSP. One USB 2. Cisco 896VA. Cisco 898EA 1. Cisco 896VA. 896VA. and Cisco 898EA. Two USB 2. Not expandable.Chapter 1 Product Overview Hardware Features Note Flash memory is not upgradable.1-compliant port located on the front panel. the fans spin as fast as necessary to minimize fan noise while maintaining a safe internal operating temperature. Cisco 860VAE series routers 256 MB Cisco 880 series routers with 512 MB embedded WLAN antennas Cisco 892FSP. Table 1-9 USB Ports Models Cisco 860 series (non-VAE) Cisco 860VAE series Cisco 880 series USB No USB ports. The USB port does not support eToken. Cisco 880 Series. Main Memory Table 1-8 describes the main onboard memory storage for different router models. Cisco 897VA. Expandable to 1 GB. The fans spin at full speed.1-compliant port located on the back panel. immediately after the router is powered up. A memory expansion slot accommodates a PC2-4200. Not expandable. One USB 1. An external USB flash memory module may be used if additional flash memory is needed.

3G Cellular Data WAN Connectivity The 3G (Evolution Data Only [EVDO]. Figure 3-27 shows the power adapter connector. but it can also be used as a primary WAN data link. Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link. The 3G express card slot is located on the front panel.5G (HSPA). The Cisco 892FSP power connector is different from the barrel-type connector on other 890 series models. see Configuring Cisco EHWIC and 880G for 3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3. Other Cisco 880G models come with embedded WAN modems for use over GSM or CDMA networks. This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the PoE 48 V external power adapter. The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a 48 V external power adapter. and 3.3af-compliant devices connected to FE ports 0 and 1. Some Cisco 880G models come with a 34-mm express card slot ready for use with a commercial 3G card radio. For information on configuring Cisco 880 series ISRs for 3G. 897VA.Chapter 1 Hardware Features Product Overview The following models have no fan: • • • • Cisco 892FSP Cisco 896VA Cisco 897VA Cisco 898EA Power Supply The Cisco 892FSP has a single +12V power supply input. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony and broadband wireless data in a mobile environment.7G (HSPA+)/3. The Cisco 896VA. 1. The AC adapter cable connector has four pins and a built-in locking mechanism. The Cisco 890 series ISRs can include an optional PoE module that provides power to 802. Cisco 860 Series. -54 VDC 80 W) and non-PoE (12 VDC 60 W) power supplies. GSM routers have two SIM card slots. see Figure 1-17 and Figure 1-19. Power over Ethernet Module The Cisco 880 series ISRs can include an optional Power over Ethernet (PoE) module that provides power to 802. and Cisco 898EA use PoE (12 VDC 43 W. Cisco 880 Series. see the Cisco 880 Series Integrated Services Routers Data Sheet. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-38 OL-16215-10 .3af-compliant devices connected to FE ports 0. For the back panels of some of these routers. These routers have antenna connectors on the back panel. 2. Note The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a 30 W power supply for non-POE-enabled routers or a 60 W power supply for POE-enabled routers. For a list of supported 3G cards.

com for feature information: http://www.4 GHz Three embedded. 2. Table 1-10 describes the radios and antennas for the Cisco 860 series.Chapter 1 Product Overview Hardware Features Wireless LAN Connectivity The embedded Wi-Fi CERTIFIED™.4 GHz and 5 GHz 100 Mb/s per radio. omnidirectional antennas: 2 dBi at 2. omnidirectional dipole antennas: 2 dBi at 2. The Cisco 880 series and 890 series routers support both autonomous and unified features and network configurations.11b/g/n draft 2. 2. 5-GHz frequency bands.11a/n and 802. Table 1-10 Wireless Device Radios and Antennas Radio Module Single-band 802. Autonomous and up to 200 Mb/s unified total Three dual-band. The wireless AP does not have an external Console port.4 GHz and 5 dBi at 5 GHz 2. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. “Connecting a Terminal or PC to the Console Port. Cisco 880 Series. omnidirectional antennas: 2 dBi at 2. dual-band. and 890 series routers. 880 series. Note Cisco 860VAE ISRs do not support wireless LAN connectivity. See the following document on Cisco.” To configure the wireless device.4 GHz 100 Mb/s per radio.11b/g/n radio modules Cisco 880 series routers with embedded WLAN antennas 2. Actual data rate is highly dependent on your wireless environment. removable.html Cisco 860 Series. The Cisco 860 series routers support autonomous features and network configurations. use the Cisco IOS command-line interface (CLI). Use the router’s Console port as described in Chapter 3.4-GHz/5-GHz omnidirectional dipole RP-TNC antenna2 1. The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1.11b/g/n radio modules Cisco 890 2.4 GHz and 5 GHz Dual-band simultaneous 802.11a/b/g/n-compliant wireless AP is preinstalled in the router as an optional feature.4 GHz Note Single-band 802. 802. 3. Maximum Data Radio Band Throughput1 2.0 radio module Platform Cisco 860 and 880 series routers Cisco 860VAE ISRs do not support wireless LAN connectivity.cisco. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-39 . 2.11a/n and 802.4 GHz Up to 100 Mb/s Mode Cisco 860 series: autonomous only Cisco 880 series: autonomous and unified Antenna Three captive. The antennas require some minor installation.com/en/US/docs/routers/access/wireless/hardware/notes/antdip. Autonomous and up to 200 Mb/s unified total Three embedded.11b/g/n radio module Dual-band 802.

For more information.0 dBi at 5 GHz AIR_ANTM5560P-R Patch 5. Corner-Mount.4 GHz 5. Ceiling-mount dual-band antenna. Cisco 880 Series.0 dBi at 5 GHz Small Form-Factor Pluggable Port The SFP port supports auto-media-detection. Table 1-11 Cisco Antennas Supported on the Cisco 890 Series ISRs Cisco Part Number AIR-ANTM2050D-R Antenna Type Omnidirectional Maximum Gain 2. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 1-40 OL-16215-10 .0 dBi at 2. see Cisco Multiband Wall-Mount. see Cisco Multiband Swivel-Mount Dipole Antenna (AIR-ANTM2050D-R).0 dBi at 2.4 GHz 5. See the Cisco 892F data sheet for a list of supported SFPs. Note Cisco supports only the antennas listed in Table 1-11 with the Cisco 890 series dual-band radio module. For more information. Wall-mount dual-band antenna.4 GHz 6. Cisco 860 Series. This antenna has a clip that allows it to be mounted on a drop-ceiling cross member.5 dBi at 2. and remote fault indication (RFI). auto-failover. It is a swivel-mount dipole dual-band blade antenna. as described in the IEEE 802. see Cisco Multiband Diversity Omnidirectional Ceiling-Mount Antenna. and Cisco 892F come with three removable dipole antennas that can be replaced using the Cisco approved antenna extenders listed in Table 1-11. For more information. or Mast-Mount Antenna.0 dBi at 5 GHz Description This is the default antenna.Chapter 1 Hardware Features Product Overview Supported Cisco Radio Antennas The Cisco 891. AIR-ANTM4050V-R Omnidirectional 4.3ah specification. Cisco 892.

and Cisco 890 series ISRs.11b/g/n Some Cisco 880 series routers contain a single 802. or router. 892.11b/g/n and 802. 866VAE-K9. The Console port may be configured as a virtual auxiliary port for dial backup and remote management. 897VAM. Cisco IOS Firewall.11a/b/g/n compliance. 867VAE-K9 All models FE1 built-in switch ports Provides connection to 10/100BASE-T (10/100-Mb/s) All models Fast Ethernet networks. The 867VAE-K9 autosensing function in these routers eliminates the need for a crossover cable and enables the router to detect MDI5 or MDIX6 in any other PC or hub with a straight-through cable or a crossover cable. 898EA All models Console or AUX port Security features Provides support for VPNs7.11a/n10 All models Provides Wi-Fi CERTIFIED™ 802. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 1-41 . Cisco 880 Series. — (10/100/1000-Mb/s) Gigabit Ethernet networks. Provides connection to 10/100BASE-T. and IPSec8. Cisco 892. and Cisco 892F have separate console and auxiliary ports. The autosensing function in these routers eliminates the need for a crossover cable and enables the router to detect MDI2 or MDIX3 in any other PC or hub with a straight-through cable or a crossover cable. 897VAMW.11a/n FE WAN port 881 891. All models 866VAE-K9. Embedded wireless AP 861. 892.11b/g/n9 and 802. Cisco 880 Series. Wireless models 802. Table 1-12 Hardware Features Available in Cisco 860 Series. Cisco 892FSP has combined console and auxiliary port. 892F Cisco 860 Series. The Cisco 890 series routers contain dual 802. The router is capable of bridging and multiprotocol routing between the LAN and WAN ports.Chapter 1 Product Overview Hardware Features Feature Summary Table 1-12 summarizes the hardware features available in the Cisco 860 series. All models 892FSP. — 867VAE. 867. an xDSL11 modem. Cisco 891. 867VAE-K9 Wireless models 802. Can be connected to 861 other network devices. Wireless models The Cisco 860 series routers contain a single 802. 897VAW. Cisco 880 series. 891.11b/g/n and 802. 860 Series All models 880 Series All models 890 Series All models — 866VAE. 802.11b/g/n radios. 892F GE4 built-in switch port Provides connection to 10/100/1000BASE-T 866VAE-K9.11a/n radios. 896VA. Provides a connection to the terminal or PC for software All models configuration or troubleshooting. 897VA.11a/n and 802. such as a cable modem. The Cisco 880 series routers also provide URL filtering.11b/g/n radio. and Cisco 890 Series ISRs Feature Reset button Description Resets the router configuration to the factory default. Resets the router configuration to customer configuration.11b/g/n radio while others contain dual 802.

Chapter 1 Hardware Features

Product Overview

Table 1-12

Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

Feature GE WAN port

Description 10/100/1000 GE WAN Port.

860 Series

880 Series

890 Series All models

866VAE, — 867VAE, 866VAE-K9, 867VAE-K9 — 887V —

VDSLoPOTS12 port ADSLoPOTS

Provides connection to a VDSL network.

— —

Provides ADSL connection over basic telephone service — with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL). Provides ADSL connection over ISDN. —

ADSLoISDN

— 892FSP, 896VA, 897VA, 897VAM, 897VAW, 897VAMW, 898EA All models

DSL Multi-mode Provides ADSL2/2+ or VDSL connection over POTS or (VDSL and ISDN (ISDN on 886VA only). ADSL2/2+)

866VAE, 886VA, 867VAE, 887VA,887V 866VAE-K9, A-M 867VAE-K9

Real-time clock (RTC)

RTC provides nonvolatile date and time when the router is powered on. The RTC is used for verifying the validity of the Certification Authority stored on the router. It is backed up by a nonreplaceable lithium battery. Supports USB 1.1. Provides connection for USB devices such as security tokens and flash memory. The Cisco 880 series routers have a single USB port; the Cisco 890 series routers have two USB ports. Cisco 880 series routers with embedded WLAN antennas have one USB 2.0 port. Cisco 892FSP and Cisco 860VAE series routers have one USB 2.0 port on the rear panel for temporary installation of a Cisco-approved USB memory device for maintenance purposes only. The port supports only USB 2.0. Refer to the product datasheet for the list of supported USB flash memory devices.
Note

866VAE, All models 867VAE, 866VAE-K9, 867VAE-K9 866VAE, All models 867VAE, 866VAE-K9, 867VAE-K9

USB port,

All models

Cisco 860VAE series router USB port does not support eToken. — Models with PoE Models with PoE

PoE13

(Optional) Provides power for 802.3af-compliant devices (such as phones) that are connected to the router. The Cisco 880 series routers support a 2-port PoE module; the Cisco 890 series routers support a 4-port PoE module.

G.SHDSL14 port 3G15 card slot

Provides 2-wire or 4-wire connection to a G.SHDSL network. Provides backup data link.

— —

888 3G models

898EA —

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-42

OL-16215-10

Chapter 1

Product Overview Hardware Features

Table 1-12

Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

Feature Dying gasp

Description Detects when the router is losing power, and sends a power-fail signal to warn the DSLAM16 about the impending line drop.

860 Series

880 Series

890 Series 892FSP, 896VA, 897VA, 897VAM, 897VAW, 897VAMW, 898EA

866VAE, 888EA, 867VAE, xDSL models 866VAE-K9, 867VAE-K9, xDSL models

Data BRI port

Provides backup and remote management functions by — connecting to the ISDN service provider if the main VDSL or G.SHDSL link fails.

xDSL 892 models, except for the 3G and SRST17 models — 881 SRST 891 —

V.92 modem FXO18 port FXS19/DID20 port BRI voice port

Provides dial backup and remote management functions if the main WAN link fails. An FXO interface connects local calls to a central office or PBX. This is the interface a standard telephone provides.

— —

An FXS interface connects directly to a standard telephone, — fax machine, or similar device. This interface supplies ringing voltage and dial tone to the station. The ISDN BRI S/T voice interface provides a client-side — (TE) ISDN S/T physical interface for connection to an NT1 device that terminates an ISDN telephone network. Supports auto-media-detection, auto-failover, and remote fault indication (RFI), as described in the IEEE 802.3ah specification. See the Cisco 892F data sheet for a list of supported SFPs. —

SRST models —

887V

SFP21 port

892F models, 892FSP, 896VA, 897VA, 897VAM, 897VAW, 897VAMW, 898EA

1. FE = Fast Ethernet. 2. MDI = media-dependent interface in normal mode. 3. MDIX = media-dependent interface in crossover mode. 4. GE = Gigabit Ethernet. 5. MDI = media-dependent interface in normal mode. 6. MDIX = media-dependent interface in crossover mode. 7. VPN = Virtual Private Network. 8. IPsec = IP security. 9. This applies to most models of the Cisco 880 series routers. 10. This applies to Cisco 880 series routers with embedded, wireless antennas. 11. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital subscriber line), and G.SHDSL. 12. VDSLoPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service. 13. PoE = Power over Ethernet. This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the PoE 48-V external power adapter.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10

1-43

Chapter 1 Hardware Features

Product Overview

14. G.SHDSL = (global industry standard) symmetrical high-speed DSL. 15. 3G = Third-Generation. 16. DSLAM = digital subscriber line access multiplexer. 17. SRST = Survivable Remote Site Telephony. 18. FXO = Foreign Exchange Office. 19. FXS = Foreign Exchange Station. 20. DID = Direct Inward Dialing. 21. SFP = small-form-factor pluggable.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-44

OL-16215-10

Do not open. Statement 1073 Cisco 860 Series. Warning All wireless LAN products in the 5. and contains the following sections: • • Equipment.S. Cisco 880 Series. Canada: Canadian Electrical Code.2/5. Tools. because they may cause serious injury or death. or where it can come into contact with such circuits. When installing the antenna.:NFPA 70. For proper installation and grounding of the antenna. Article 810. Statement 372 Warning Read the installation instructions before connecting the system to the power source. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 2-1 . take extreme care not to come into contact with such circuits. Statement 1030 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1052 Warning No user-serviceable parts inside. Statement 1004 Warning Only trained and qualified personnel should be allowed to install.3GHz band cannot be used outdoors. Section 54). Statement 1040 Warning Do not locate the antenna near overhead power lines or other electric light or power circuits. and Connections. page 2-3 Note For compliance and safety information. replace. page 2-2 Installing the Router.CH A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series. please refer to national and local codes (for example. see the Regulatory Compliance and Safety Information Roadmap that ships with the router and the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. U. Use the product only indoors. National Electrical Code. and 890 series Integrated Services Routers (ISRs). or service this equipment. 880 series.

and Connections Installing the Router Equipment. Shipped with Cisco 886. Cisco 880 Series. 6. By default. no cables are shipped with Cisco 860VAE models unless requested through the dynamic configuration tool. 6 2 Cisco 860 Series Routers 1 — 1 1 1 1 1 3 Cisco 860VAE Series Routers1 — — n/a n/a — 1 1 1 Cisco 880 Series Routers 1 — 1 1 1 1 1 1 4 5 Cisco 890 Series Routers 1 1 1 1 1 1 1 1 — 1. 887M. Cisco CP is optional by order and available only on some SKUs. Table 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series.Chapter 2 Equipment. DSL = digital subscriber line. and Connections This section describes the equipment. Shipped with Cisco 888E models only. and connections necessary for installing your Cisco 860 series. page 2-3 Ethernet Devices. Tools. Shipped with Cisco 867 models only. 4. Table 2-1 lists the items and their quantities that are shipped with each router model. tools. 880 series. 887. and 890 series ISRs. page 2-2 Connections. page 2-3 Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the router. Tools. 3. Screws for mounting the router on a wall: Cisco 860 Series. page 2-2 Additional Items. and 886-J models only. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-2 OL-16215-10 . 5. and Cisco 890 Series ISRs Item Straight-through RJ-45 Ethernet cable ADSL RJ-11-to-RJ-11 straight-through cable RJ-11 DSL cable DSL RJ-45-to-dual-RJ-11 breakout cable RJ-45-to-DB-9 console cable External 12 VDC power supply adapter AC power supply cable with cable retention clip Cisco Configuration Professional (Cisco CP) CD 2. Cisco 880 Series. It contains the following topics: • • • • Items Shipped with your Router. Additional Items The following items are not shipped with the router but are required for installation: • • ESD-preventive cord and wrist strap.

The screws must be long enough to penetrate at least 3/4 in. page 2-7 Mounting on a Wall. Cisco 880 Series. This section also describes how to attach WLAN antennas to the Cisco 890 series routers. and workstations or PCs. • • • • If you plan to configure the software using Cisco IOS commands through the console port. (5 to 7 mm). servers. or two number-10 washer-head screws. page 2-8 Installing in a Rack. and 890 series ISRs. This section contains the following topics: • • • • • • • Warnings. These routers can either be installed on a table top or other flat horizontal surface or be mounted on a wall. provide a Kensington or equivalent locking cable. • • Ring terminal with an inner diameter of 1/4 in. for NEC-compliant chassis grounding. page 2-13 Installing the FIPS Cover.Chapter 2 Installing the Router Installing the Router – Two number-10 wood screws (round. provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port. Connections Obtain a broadband or Ethernet connection from your service provider. – AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding. • • Wire crimper for chassis grounding. Installing the Router This section describes how to install the Cisco 860 series. Ethernet Devices Identify the Ethernet devices that you will connect to the router: hub. page 2-14 Cisco 860 Series. The Cisco 890 series ISRs may be mounted in a rack. 880 series. page 2-4 Installing on a Table. for mounting the router on a hollow-wall. for mounting on a wall stud. (20 mm) into the supporting wood or metal wall stud. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports. provide the modem and modem cable.or pan-head) with number-10 washers. page 2-4 Installing Antennas. provide an NT1 device and an ISDN S/T cable. If you plan to connect a modem. If you plan to use the Data BRI port. page 2-11 Installing the Router Ground Connection. Wire for connecting the chassis to an earth ground: – AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding. If you plan to use the cable-lock feature. – Two number-10 wall anchors with washers. Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 2-3 .

including heating vents. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. overheating could occur and cause damage to the router. Statement 1024 Warning Read the wall-mounting instructions carefully before beginning installation.4-GHz to 5-GHz omnidirectional dipole antennas. otherwise. Cisco 880 Series. overheating could occur and cause damage to the router. Do not keep any object in direct contact with the surface for a prolonged period. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Caution Do not place anything on top of the router that weighs more than 10 pounds (4. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-4 OL-16215-10 .5 kilograms). Excessive weight on top of the router could damage the chassis. Place router in ventilated area to avoid local air heating. otherwise. Cisco 860 Series. Caution Do not cover or obstruct the router vents located on both sides of the router. Statement 242 Warning This equipment must be grounded. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. and do not stack routers on a desktop.Chapter 2 Installing the Router Installing the Router Warnings Warning This equipment needs to be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Statement 378 Note • • • Do not stack anything on top of the router. Caution Do not install the router or power supplies next to a heat source of any kind. Do not cover or obstruct the router vents located on both sides and top of the routers. Installing Antennas The Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel. Caution The top surface of the router is hot since heat is dissipated through the top. The antennas that are shipped with the router are dual-band 2.

2/5. wall.3GHz band cannot be used outdoors. b. For optimum wireless performance. Use the product only indoors. Statement 372 Note Before you install the Cisco 890 series wireless router on a table. Cisco 860 Series. orient the antennas straight up.Chapter 2 Installing the Router Installing the Router Warning All wireless LAN products in the 5. If the router is being mounted on a wall. To attach the radio antennas to your wireless router. Figure 2-1 Attaching Antennas to the Router Step 2 Orient the antennas. the antennas should be perpendicular with respect to the floor. If the router is being mounted on a desk. connect the antennas to the back panel. It is difficult to attach the antennas after the router is installed. a. Cisco 880 Series. follow these steps: Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router. orient the antennas perpendicular to the floor. as shown in Figure 2-2 and Figure 2-3. or rack. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 2-5 272486 .

Chapter 2 Installing the Router Installing the Router Figure 2-2 Antennas Oriented Vertically Up Cisco 860 Series. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-6 274774 OL-16215-10 .

see the “Installing the Router Ground Connection” section on page 2-13. Cisco 880 Series.Chapter 2 Installing the Router Installing the Router Figure 2-3 Antennas Oriented Vertically Down Installing on a Table To install the router on a table or other flat horizontal surface. For the chassis ground connection procedures. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 274775 2-7 .5 cm) of clear space beside the cooling inlet and exhaust vents. Connect the chassis to a reliable earth ground. Note Do not place anything on top of the router. Keep at least 1 inch (2. firmly place the router on a table or other horizontal surface.

the distance between mounting holes is 8. To mount the router on a wall. consider cable limitations and wall structure. Note For most router models.5 cm) of clear space beside the cooling inlet and exhaust vents. Figure 2-4 shows the wall-mount holes located on the underside of the router. The mounting holes are bidirectional. 880 series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-8 OL-16215-10 .Chapter 2 Installing the Router Installing the Router Mounting on a Wall The Cisco 860 series. the distance is 7. Cisco 860 Series. follow these steps: Step 1 Determine the required distance between mounting holes on the router. You can hang the router with the front bezel facing upward or downward. Cisco 880 Series.85 inches (199 mm). For the Cisco 866 and Cisco 867 models. Tip When choosing a location for wall-mounting the router. as shown in Figure 2-4.2 inches (208 mm). and 890 series ISRs have mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface. Verify the required distance before drilling the holes. Keep at least 1 inch (2.

Cisco 860 Series.32 cm) between the screw head and the wall. into the wall. 1 1 5. See Figure 2-5.Chapter 2 Installing the Router Installing the Router Figure 2-4 Wall-mount Holes on the Underside of the Router 8. 1 Step 2 Step 3 Wall-mount holes Insert the screws. with anchors.961 in.673 in. The screw head may damage the protection wall inside. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 231987 2-9 . Place the power adapter on a nearby horizontal surface.200 in. 3. See Figure 2-5. Leave 1/8 inch (0. Hang the router on the screw without forcibly pushing towards the wall side.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-10 231982 OL-16215-10 .Chapter 2 Installing the Router Installing the Router Figure 2-5 Router Mounted on the Wall 1 1 4 2 3 1 2 Two number-10 wood screws mounted on the 3 wall Wall-mount holes 4 Horizontal surface on which to place the power adapter Distance between the screw head and the wall. Cisco 860 Series. For the chassis ground connection procedures. see the “Installing the Router Ground Connection” section on page 2-13.32 cm) Step 4 Connect the chassis to a reliable earth ground. Cisco 880 Series. (0. 1/8 in.

Use a number 2 Phillips screwdriver to install the bracket screws on both sides of the chassis. Figure 2-7 Attaching the Rack-mount Brackets to the Cisco 890 Series ISR Cisco 860 Series. attach the rack-mount brackets to the Cisco 890 series ISR chassis.Chapter 2 Installing the Router Installing the Router Installing in a Rack The Cisco 890 series ISRs can be mounted in a rack. Caution Do not over torque the screws. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 2-11 272484 278159 . as shown in Figure 2-7.9 N-m). Use two screws on each side. The recommended torque is 6 to 8 in-lb (0. follow these steps: Step 1 Remove the screws. as shown in Figure 2-6.7 to 0. To install a Cisco 890 series ISR in a rack. Cisco 880 Series. Figure 2-6 Screw Locations 1 1 1 Step 2 Screws Using the screws provided.

If the rack is provided with stabilizing devices. For the chassis ground connection procedures.Chapter 2 Installing the Router Installing the Router Caution Chassis installation must allow unrestricted airflow for chassis cooling. Step 4 Step 5 Place the power adapter on a nearby horizontal surface. Cisco 860 Series. When mounting this unit in a partially filled rack. attach the Cisco 890 series ISR with rack-mount brackets to a 19-inch rack. resting the brackets on the lower screws while you insert the upper pair of screws. Start with the lower pair of screws first. When the correct screw holes are used. install the stabilizers before mounting or servicing the unit in the rack. you must raise or lower the brackets to the next rack hole. The following guidelines are provided to ensure your safety: • • • This unit should be mounted at the bottom of the rack if it is the only unit in the rack. you must take special precautions to ensure that the system remains stable. Keep at least 1 rack unit of space above the router. Connect the chassis to a reliable earth ground. Cisco 880 Series. Warning To prevent bodily injury when mounting or servicing this unit in a rack. load the rack from the bottom to the top with the heaviest component at the bottom of the rack. see the “Installing the Router Ground Connection” section on page 2-13. Tip The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-12 OL-16215-10 . Note Do not stack equipment directly above the router. the small threaded holes in the brackets line up with unused screw holes in the rack. Statement 1006 Step 3 Using two screws for each side (supplied with the rack). Note Be sure to leave space above and below each unit in a rack to allow for cooling air circulation. If the small holes do not line up with the rack holes.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 2-13 231981 . use size 18 AWG (1 mm2) or larger copper wire. you can connect the power wiring. use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. Install the ground wire in accordance with local electrical safety standards. (5 to 7 mm).1 N-m).Chapter 2 Installing the Router Installing the Router Installing the Router Ground Connection The router must be connected to a reliable earth ground. For a ring terminal. use one of the screws provided.9 to 1. For a ground lug. as shown in Figure 2-8. use the two provided screws with captive locking washers. the WAN and LAN cables. For EN/IEC 60950–compliant grounding. and the cables for administrative access as required for your installation. Figure 2-8 Chassis Ground Connection Using Ring Terminal 1 1 Step 4 Ring terminal Connect the other end of the ground wire to a known reliable earth ground point at your site. To install the ground connection. After you install and properly ground the router. using the wire crimper. Attach the ground lug or ring terminal to the chassis. follow these steps: Step 1 Step 2 Step 3 Strip one end of the ground wire to the length required for the ground lug or terminal. Cisco 860 Series. Crimp the ground wire to the ground lug or ring terminal. • • For NEC-compliant grounding. Tighten the screws to a torque of 8 to 10 in-lb (0. Cisco 880 Series.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-14 OL-16215-10 284921 . Cisco 880 Series.Chapter 2 Installing the Router Installing the Router Installing the FIPS Cover Perform the following steps to install the FIPS cover in the router: Step 1 Remove the four mounting screws of the top cover. Cisco 860 Series.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 2-15 284922 . Detail A Adapter Plate Step 3 Step 4 Rotate and bring into the close position to hinge to the correct hexagon.Chapter 2 Installing the Router Installing the Router Step 2 Install the left-side FIPS cover. as shown in detail A. Cisco 860 Series. Cisco 880 Series. Place the adapter plate before closing by aligning the mounting holes.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 2-16 OL-16215-10 284924 284923 .Chapter 2 Installing the Router Installing the Router Step 5 Secure the FIPS cover with two mounting screws. Cisco 860 Series. Step 6 Step 7 Install the right-side FIPS cover the same way as the left-side FIPS cover. View after both covers are installed. Cisco 880 Series.

Chapter 2

Installing the Router Installing the Router

Step 8

If the FIPS covers are installed with the rack mount brackets, the adapter plates are not required in the installation.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10

2-17

284925

Chapter 2 Installing the Router

Installing the Router

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-18

OL-16215-10

CH A P T E R

3

Connecting the Router
This chapter describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and a network. The chapter contains the following sections:
• • • • • • • • • • • • • • • • • • • • •

Safety Warnings, page 3-2 Preparing to Connect the Router, page 3-4 Connecting a PC, Server, or Workstation, page 3-5 Connecting a Phone, page 3-6 Connecting an External Ethernet Switch, page 3-7 Connecting the V.92 modem Port, page 3-8 Connecting a Terminal or PC to the Console Port, page 3-9 Connecting a Modem to the Auxiliary Port, page 3-10 Connecting the 3G Card, page 3-11 Installing the 3G Adapter for Extended Cable/Antenna, page 3-17 Connecting a Data BRI Port, page 3-21 Connecting an FE Line to an FE WAN Port, page 3-23 Connecting a GE Line to an GE WAN Port, page 3-24 Connecting an xDSL Line, page 3-25 Connecting Power over Ethernet, page 3-27 Connecting the AC Adapter, page 3-28 Connecting an FXS Line, page 3-32 Connecting an FXO Line, page 3-34 Connecting a Voice ISDN BRI Line, page 3-35 Connecting a Small Form-Factor Pluggable Module, page 3-37 Verifying Connections, page 3-40

Note

For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10

3-1

However. LAN ports contain SELV circuits. Safety Warnings Warning When installing the product. Statement 371 Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-2 OL-16215-10 . To avoid electric shock. detach the end away from the unit first. Statement 1001 Warning This equipment has been designed for connection to TN and IT power systems. Statement 1015 Warning Take care when connecting units to the supply circuit so that wiring is not overloaded. Replace the battery only with the same or equivalent type recommended by the manufacturer. and WAN ports contain TNV circuits. Dispose of used batteries according to the manufacturer’s instructions. Use caution when connecting cables. Statement 1030 Cisco 860 Series. When detaching cables. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” or “CSA” shown on the cord). Statement 1007 Warning There is the danger of explosion if the battery is replaced incorrectly. Non-wireless routers do not have antennas or antenna connectors on the back panel. use caution when working near WAN ports. Note Depending on the features available for your router. or service this equipment. Cisco 880 Series. not regulated with the subject law by showing “PSE” on the cord. Statement 1021 Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. some content in this chapter may not apply to your router. Statement 1018 Warning To avoid electric shock. the procedures for connecting devices to the router are the same for both wireless and non-wireless routers. Using any other cables/adaptors could cause a malfunction or a fire. replace. please use the provided or designated connection cables/power cables/AC adaptors/batteries. do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits.Chapter 3 Safety Warnings Connecting the Router Note The illustrations in this chapter show a wireless router with antennas attached. Statement 1026 Warning Only trained and qualified personnel should be allowed to install. for any other electrical devices than products designated by CISCO. Some LAN and WAN ports both use RJ-45 connectors.

Cisco 880 Series. For proper installation and grounding of the antenna. wash bowl. or near a swimming pool. The ringer is activated by an incoming call. disconnect the telephone-network cables to avoid contact with telephone-network voltages. for example. U. There may be a remote risk of electric shock from lightning. Statement 1074 Cisco 860 Series.:NFPA 70. Statement 1036 Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.Chapter 3 Connecting the Router Safety Warnings Warning Do not use this product near water. Statement 1041 Warning This equipment contains a ring signal generator (ringer). Do not touch the RJ-11 (phone) port wires (conductors). the conductors of a cable connected to the RJ-11 port. because they may cause serious injury or death. Statement 1052 Warning No user-serviceable parts inside. Canada: Canadian Electrical Code. Statement 1042 Warning Do not locate the antenna near overhead power lines or other electric light or power circuits. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-3 . kitchen sink or laundry tub. please refer to national and local codes (for example. When installing the antenna. Statement 1035 Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Do not open. Statement 1038 Warning To report a gas leak. Statement 1073 Warning Installation of the equipment must comply with local and national electrical codes. in a wet basement. near a bath tub. take extreme care not to come into contact with such circuits. Article 810.S. Statement 1039 Warning Before opening the unit. Statement 1037 Warning Avoid using a telephone (other than a cordless type) during an electrical storm. or the associated circuit-board when the ringer is active. do not use a telephone in the vicinity of the leak. which is a source of hazardous voltage. Section 54). National Electrical Code. or where it can come into contact with such circuits.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-4 OL-16215-10 . see “Technical Specifications” section on page A-1 for cabling specifications. follow these guidelines when connecting devices to your router: • Turn off power to the devices and to the router until all connections are completed. install the router according to the instructions in “Installing the Router” section on page 2-1 Preventing Damage to the Router To prevent damage to your router. Cisco 880 Series. we strongly recommend ordering the cable from Cisco.Chapter 3 Preparing to Connect the Router Connecting the Router Preparing to Connect the Router Before you connect the router to the devices. If you must supply your own cable. If this appendix does not provide specifications for a particular cable. Caution Do not turn on the devices until after you have completed all connections to the router. • • Connect the color-coded cables supplied by Cisco to the color-coded ports on the back panel. Cisco 860 Series.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-5 . Figure 3-1 Connecting a Server. (Optional) Connect additional servers. Cisco 880 Series. or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port. or Workstation Connecting a PC. follow these steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Server. Cisco 860 Series. Server. or workstations to the other Ethernet switch ports.Chapter 3 Connecting the Router Connecting a PC. or workstation. See Cisco Configuration Professional Quick Start Guide for more information. server. Note Use the Cisco Configuration Express to configure the Internet connection settings. or Workstation 2 1 3 231989 1 2 Step 2 Step 3 Yellow Ethernet cable supplied with the router 3 Ethernet switch port on the router RJ-45 port on the network interface card Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed in the PC. PCs. Figure 3-1 shows a Cisco 888W router connected to a PC. PC.

follow these steps: Note A power source must be provided for the phone to function. Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-6 OL-16215-10 270551 .Chapter 3 Connecting a Phone Connecting the Router Connecting a Phone To connect an 802. Cisco 880 Series.3af-compliant phone to an Ethernet switch port. or by using an external AC power source connected to the phone. This can be done in two ways: the phone can be powered via the PoE function using the PoE enabled Ethernet ports. Figure 3-2 Connecting a Phone Step 1 2 1 3 1 GHI ABC 2 5 8 DEF 3 6 9 # 4 7 JKL MNO PQRS TUV WXYZ * OPER 0 1 2 Yellow Ethernet cable Ethernet switch port 1 on the router 3 RJ-45 port on a phone Cisco 860 Series. Figure 3-2 shows a Cisco 888W router connected to a phone.

you can add Ethernet connections to the router by connecting an external Ethernet switch to the Ethernet switch on the router. Turn on the Ethernet switch. connecting to an external Ethernet switch port 2 Step 2 Step 3 Available port on the external Ethernet switch Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet connections. Figure 3-3 shows a Cisco 888W router connected to an Ethernet switch. complete the following steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. RJ-45–to–RJ-45. Connecting an External Ethernet Switch If more than four PCs in an office must be connected to each other. Figure 3-3 Connecting to an Ethernet Switch 1 3 1 SYSTEM RPS MODE STATUS UTIL DUPLX SPEED 2X 1X 2 3 4 5 6 7 8 9 10 11 12 15X 1X 1 2 3 4 5 6 7 8 9 10 11 12 15X 16X 2X Catalyst 350 1 16X 0 SERIES XL 2 INLINE POWE R 2 1 Ethernet switch port on the router 3 Yellow CAT5 Ethernet cable.Chapter 3 Connecting the Router Connecting an External Ethernet Switch Step 2 Connect the other end of the cable to the RJ-45 port on the phone. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 231986 3-7 . To connect an external Ethernet switch to an Ethernet switch port on the router. Cisco 880 Series.

Cisco 880 Series. To avoid electric shock.Chapter 3 Connecting the V. Figure 3-4 Connecting to Your Service Provider Through the V. When detaching cables.92 port.92 modem Port Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-8 OL-16215-10 272387 .92 port on the router 2 Telephone wall outlet To connect the router to your service provide network through the V. Statement 1026 For dialup connection to your service provider network through the V. Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet.92 port 1 2 1 V. use caution when working near WAN ports.92 port. follow these steps: Step 1 Step 2 Connect one end of the straight-through R-J11 cable to the V. Cisco 860 Series.92 port. which show this connection. detach the end away from the unit first.92 modem Port Connecting the Router Connecting the V. follow the steps given after Figure 3-4.

follow these steps: Step 1 Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router. Cisco 880 Series. Step 3 To communicate with the router.Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console Port Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console Auxiliary (Aux) port either to configure the software by using the CLI or to troubleshoot problems with the router. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 231990 3-9 . Figure 3-5 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router. start a terminal emulator application. Figure 3-5 Connecting a Terminal or PC to the Console Port 1 2 1 RJ-45 connector to the Console Aux port on the router 2 DB-9 connector Step 2 Connect the DB-9 end of the DB-9–to–RJ-45 serial cable to the to the COM port on your laptop or PC. Note Some laptops and PCs do not come with DB-9 serial port connectors and may require a USB-to-serial port adapter. To connect a terminal or PC to the console port on the router and access the CLI.

Figure 3-6 Connecting a Modem to the Aux Port 1 2 3 4 1 2 Aux port (RJ-45) Light blue console cable 3 4 DB-9 to DB-25 modem adapter (if required) Modem Cisco 860 Series. follow these steps: Step 1 Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-6. For more information on terminal emulation settings. see Applying Correct Terminal Emulator Settings for Console Connections. the router prompt is displayed. Cisco 880 Series.Chapter 3 Connecting a Modem to the Auxiliary Port Connecting the Router Terminal Emulator Settings Use the following settings for the terminal emulator connection: • • • • 9600 baud 8 data bits. Connecting a Modem to the Auxiliary Port To connect a modem to the router. no parity 1 stop bit No flow control When the terminal emulator establishes communications. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-10 OL-16215-10 272386 .

To connect and secure the 3G card. provided by their network carrier. see Configuring Cisco EHWIC and 880G for 3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3. Note The Cisco 880G router does not support online insertion and removal (OIR) of the third-generation (3G) card. Cisco 880 Series. follow these steps: Step 1 Align the 3G card to the 3G express card slot. Keep the card parallel to the surface and firmly push the card into the slot. Note When inserting the card into the 3G express card slot. You must enter the shutdown command on the cellular interface before you remove the 3G card from the router. The 3G card is designed to fit tightly into the 3G express card slot. Connecting the 3G Card Note For information on embedded multiband. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-11 . into the 3G card. you may hear a metal-on-metal sound as the 3G card rubs against the internal metal cage. Cisco 860 Series. as shown in Figure 3-7.7G (HSPA+)/3. Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR). Firm pressure may be required to insert the card. Connect the DB-25 end of the modem adapter to the modem. Tip Holding the 3G card on the flat metal surface makes it easier to align and insert the 3G card.Chapter 3 Connecting the Router Connecting the 3G Card Step 2 Step 3 Step 4 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. multiservice WAN modems. Note Global System for Mobile Communications (GSM) customers need to insert a SIM card.5G (HSPA).

HSPA = High-Speed Packet Access.Chapter 3 Connecting the 3G Card Connecting the Router Figure 3-7 Inserting the 3G Card 4 271473 3 2 3 1 2 3 1 6 5 5 4 5 6 Screw holes for locking bracket Pin holes for aligning the locking bracket SIM slot (in HSPA1 cards only) 3G card with the Cisco logo facing up 3G express card slot Notches on the 3G card 1. as shown in Figure 3-8. Figure 3-8 Opening the Anti-theft Locking Bracket Front View Back View 1 1 1 Pins on the locking bracket for alignment Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-12 271474 OL-16215-10 . Cisco 880 Series. Step 2 Open the top of the anti-theft locking bracket.

Figure 3-9 Installing the Locking Bracket 1 3 2 271726 1 2 3G card Locking bracket 3 Notch on the 3G card Cisco 860 Series. and the pins on the locking bracket should be inserted into the corresponding holes in the router. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-13 .Chapter 3 Connecting the Router Connecting the 3G Card Step 3 Slide the opened locking bracket under the 3G card. as shown in Figure 3-9. The locking bracket should align with the notches on either side of the 3G card.

insert the antenna connector into the antenna connector receptacle on the 3G card. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-14 OL-16215-10 . as shown in Figure 3-10. Cisco 880 Series. and tighten with a number 2 Phillips screwdriver. Cisco 860 Series.Chapter 3 Connecting the 3G Card Connecting the Router Step 4 Close the locking bracket. Figure 3-10 Closing the Locking Bracket 1 2 271580 1 Step 5 3G card 2 Locking bracket Insert the screws. Figure 3-11 Inserting the Screws 4 271476 1 3 4 2 1 2 Step 6 3G card Locking bracket 3 4 Screws Screw holes on the locking bracket To connect the antenna to the 3G card. as shown in Figure 3-11.

Please locate the receptacle of your card before plugging in the cable. or front of the 3G card. and Figure 3-13 shows the antenna with the SMK-TS-9 connector. The antenna connector receptacle is located on either the left. Figure 3-12 shows the antenna connected to the 3G card with an SSMB type plug. Figure 3-12 Antenna connected to the 3G Card with SSMB connector 1 272653 3 2 1 2 Antenna on a cradle Antenna SSMB connector 3 Antenna connector receptacle1 1. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-15 .Chapter 3 Connecting the Router Connecting the 3G Card Note The antenna connector receptacle may be located on the left. right. depending on your card. Cisco 860 Series. right or front of the card for different SKUs.

Table 3-1 lists the different adapters and SKUs supported by each adapter.Chapter 3 Connecting the 3G Card Connecting the Router Figure 3-13 Antenna with the SMK-TS. the adapters come with different connectors. PCEX-3G-CDMA-S. with an SMK-TS-9 to TNC connector. PCEX-3G-CDMA-B. follow Step 7. see the “Installing the 3G Adapter for Extended Cable/Antenna” section on page 3-17. PCEX-3G-HSPA-A. CISCO881G-V-K9 Step 7 Clean the flat surface to which you will affix the antenna. PCEX-3G-HSPA. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-16 279085 OL-16215-10 . PCEX-3G-CDMA-V. CISCO881G-G-K9 Use this with the pentaband dipole indoor antenna (3G-ANTM-SMKTS9). For instructions on how to install the adapter. Otherwise. CISCO881G-S-K9. Cisco 880 Series. 3G-ACC-SSMB-TNC 3G adapter for extended cable/antenna with an SSMB to TNC connector.9 Connector Original antenna assembly SMK-TS-9 connector Cable If you are using an extension cable. you must attach the 3G adapter for extended cable antenna to the body of the router. CISCO881G-A-K9. Use this with the pentaband dipole indoor antenna shipped with your product. Depending on the SKU ordered. Table 3-1 3G Adapters and Supported SKUs 3G Adapter SKU Description SKUs Supported 3G-ACC-SMKTS9-TNC 3G adapter for extended cable/antenna PCEX-3G-HSPA-R6.

Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/Antenna Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-17 . 3G-ACC-SMKTS9-TNC. Installing the 3G Adapter for Extended Cable/Antenna For better signal and reception. then firmly press the cradle to the flat surface. Cisco 880 Series. if you are using the Cisco 3G Adapter for Extended Cable/Antenna. Figure 3-14 Locating the Phillips Screw 2 1 2 1 279124 Phillips screw on the left side of router 2 Air vent holes to be aligned with adapter Cisco 860 Series. follow these steps to install it: Step 1 Locate and remove the Phillips screw on the left side of the router as shown in Figure 3-14. Keep the screw aside for Step 4.

Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-18 279123 OL-16215-10 . Cisco 860 Series. Figure 3-16 Inserting the Hooks 1 279122 1 1 Hooks aligned and inserted into the router.Chapter 3 Installing the 3G Adapter for Extended Cable/Antenna Connecting the Router Step 2 Locate the hooks on the adapter as shown in Figure 3-15. Figure 3-15 Locating the Hooks on the Adapter 1 1 Step 3 Hooks on the adapter Align and insert the hooks of the adapter into the air vent holes on the left side router body as shown in Figure 3-16.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 279091 3-19 .Chapter 3 Connecting the Router Installing the 3G Adapter for Extended Cable/Antenna Step 4 Align the circular adapter hole with the hole on the router chassis from where you removed the screw in Step 1 and use the screw to attach the adapter to the router as shown in Figure 3-17. Cisco 880 Series. Figure 3-17 Attaching the Adapter Cisco 860 Series.

Chapter 3 Installing the 3G Adapter for Extended Cable/Antenna Connecting the Router Step 5 Connect the extension cable to the 3G card. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-20 279089 OL-16215-10 . Table 3-2 lists the loss information for the ultra-low-loss (ULL) LMR 400 cables available with the adpater for the 3G fixed platforms. Cisco 860 Series. as described in the “Connecting the 3G Card” section on page 3-11. Figure 3-18 Adapter Connected to 3G Card and Router Chassis 1 2 3 5 6 4 1 2 3 Router chassis 3G adapter for extended cable/antenna Cable 4 5 6 SSMB or SMK-TS-9 connector 3G card inserted into the router 3G card Now the adapter is ready for use with the extension cable. The complete assembly is shown in Figure 3-18.

the antenna picks up the least signal. However. this procedure applies to all Cisco 880 series router with a Data BRI port. To avoid damage to the router. The signal is received by the antenna as a result of it bouncing off of reflective surfaces. depending on where the antenna is placed. and the second cable connects the splitter to the wall jack. The cabling requirements for the ISDN S/T connection are as follows: • • You must provide two unshielded Category 5 cables. Cisco 880 Series.66 dB 0.Chapter 3 Connecting the Router Connecting a Data BRI Port Table 3-2 Cisco Adapter Cables for Use with 3G Fixed Routers Cisco Product Number 3G-ACC-SSMB-TNC 3G-ACC-TS9-TNC Antenna Adapter Length 14. do not connect telephone-network voltage (TNV) circuits (such as ISDN or DSL circuits) to safety extra-low voltage (SELV) circuits (such as LAN circuits).5 inches 13. if the antenna orientation is horizontal. The first cable connects the NT1 box to the splitter. it may receive different signal strengths. an RJ-45–to–RJ-11 ISDN S/T cable is available upon request if the wall jack at the site requires an RJ-11 connector. Cisco 860 Series. Hence. For additional information on all the available cables and antennas available for 3G.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm. Although the following procedure shows a Cisco 888W data router. the receiving antenna needs to be vertically oriented too in order to receive the best signal.SHDSL]) WAN service fails. go to: http://www. As the angle of the antenna orientation is changed from vertical to horizontal. Typically.62 dB Frequency (MHz) 2100 2100 Note Antenna orientation can increase or decrease signal reception due to polarization. including global industry standard symmetrical high-speed DSL [G. Caution Both LAN and WAN ports use RJ-45 connectors. Therefore. an SP’s transmitting antenna on the BTS is a vertically polarized omnidirectional antenna. There are RJ-45 connectors at both ends of the default orange ISDN S/T cable. Hence.html#w p1262730 Connecting a Data BRI Port You can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in case the primary xDSL (general term referring to various forms of DSL. The Data BRI connection is not available on the third-generation (3G) models.cisco. which means the electromagnetic waves are transmitted from it in a vertical plane.5 inches Insertion Loss 0. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-21 . Use caution when connecting cables to these connectors. Contact your router reseller for the appropriate cable. the recommended position is vertical. However. only an angular component of the signal is picked up by the antenna.

Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter to the wall jack to allow a link to the network service provider. Connect the first unshielded CAT 5 cable from the U-port on the NT1 box to the telephone line port on the splitter. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-22 OL-16215-10 . follow these steps: Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-19 Connecting the Data BRI Port to the ISDN Line 1 3 7 2 4 6 5 8 9 231991 5 10 1 2 3 4 5 Step 2 Step 3 Step 4 Data BRI port on the router ISDN S/T cable Network termination 1 (NT1) box S/T port on the NT1 box Unshielded CAT 5 cable 6 7 8 9 U-port on the NT1 box xDSL splitter (provided by the xDSL service provider) Telephone line port on the splitter Telecommunication service port on the splitter 10 Wall jack Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box. Figure 3-19 shows a Data BRI connection.Chapter 3 Connecting a Data BRI Port Connecting the Router To connect the Data BRI port to the ISDN service provider. Cisco 880 Series. Cisco 860 Series.

Cisco 860 Series. Cisco 880 Series.Chapter 3 Connecting the Router Connecting an FE Line to an FE WAN Port Connecting an FE Line to an FE WAN Port To connect the Fast Ethernet (FE) WAN port on the router. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 231992 3-23 . follow these steps: Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-20. Figure 3-20 Connecting the FE WAN Port 1 WAN FE 4 1 2 3 Internet 1 2 Step 2 FE WAN port CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem.

Chapter 3 Connecting a GE Line to an GE WAN Port Connecting the Router Connecting a GE Line to an GE WAN Port To connect the Gigabit Ethernet (GE) WAN port on the router. Figure 3-21 Connecting the GE WAN Port 1 2 3 Internet 1 2 Step 2 GE WAN port CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-24 274493 OL-16215-10 . Cisco 880 Series. follow these steps: Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-21.

and CSA/EN/IEC/UL 60950-1.. ITU-T K. use only No. kitchen sink or laundry tub. for example. There may be a remote risk of electric shock from lightning. or near a swimming pool. Statement 1039 Warning There is the danger of explosion if the battery is replaced incorrectly. Caution To reduce the risk of fire. To avoid electric shock. use caution when working near WAN ports. detach the end away from the unit first.Chapter 3 Connecting the Router Connecting an xDSL Line Connecting an xDSL Line Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. These devices are normally installed by the service provider.g. wash bowl. Warning Do not use this product near water. Cisco 880 Series. See Figure 3-22 for the likely location of the primary protection device. do not use a telephone in the vicinity of the leak. IEC 61000-4-5. Statement 1038 Warning To report a gas leak. Please contact your sales team or qualified service person for further information and installation. These standards assume Primary Protection devices protect the Customer Premise Equipment (CPE). Replace the battery only with the same or equivalent type recommended by the manufacturer. or demarcation point. Statement 1015 Cisco 860 Series. 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord. 26 AWG or larger (e. local exchange carrier or qualified service person and are located at the telecom service provider entrance.21. Statement 1026 Caution Cisco Systems DSL WAN Interfaces are tested for compliance with regulatory standards such as FCC Part 68. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-25 . Dispose of used batteries according to the manufacturer’s instructions. When detaching cables. network interface box. in a wet basement. near a bath tub. The primary protection device must be suitable for the xDSL interface employed. Statement 1035 Warning Avoid using a telephone (other than a cordless type) during an electrical storm.

VDSL2oPOTs port. See Figure 3-23. Figure 3-23 Connecting the xDSL Line 1 2 1 G. Cisco 880 Series. Cisco 860 Series.SHDSL) line. or ADSL2+ port 2 DSL wall jack Step 2 Connect the other end of the cable to the DSL wall jack. or an ADSL2+ line.Chapter 3 Connecting an xDSL Line Connecting the Router Figure 3-22 Primary Protection Device Location Telecom Service Overhead Service Entrance Home or Business Router Service Utilities Entrance or Demarcation Point Network Interface Box/ Network Interface Device/ Station Protector To connect the router to a global industry standard symmetrical high-speed DSL (G. very-high-speed digital subscriber line 2 (VDSL2) port. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-26 232175 281392 Note: Primary Protection may be located Outside or Inside of Premise * Alternative Underground Service Entrance Building Ground Rod connected to Service entrance and Primary Protection OL-16215-10 . follow these steps: Step 1 Connect one end of an RJ-11 (RJ-45 on 880 E models) cable to the port on the router.SHDSL port.

Connecting Power over Ethernet Warning This unit might have more than one power supply connection.3af compliant power source or an IEC60950 compliant limited power source. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-27 . Cisco 880 Series.Chapter 3 Connecting the Router Connecting Power over Ethernet Caution The primary WAN port is designed for an RJ-45 connector only. Statement 1028 Warning This product must be connected to a power-over-ethernet (PoE) IEEE 802.1. Note The router must also be connected to an AC power outlet through a 12-VDC adapter. All connections must be removed to de-energize the unit. Statement 353 Figure 3-24 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter to your router. and 3 of the 8-port 10/100 FE switch on the Cisco 890 series routers. Note Be sure that the internal PoE is enabled for this connection procedure to work. On Cisco 860VAE routers. To connect the router to an AC outlet. 2. check the DSL Link LED. see the“Connecting the AC Adapter” section on page 3-28. Damage to the primary WAN port may occur if a non-RJ-45 connector is inserted Note The DSL line must be provisioned by your service provider and correctly configured so that the LED shows the carrier detect (CD) status. Cisco 860 Series. The PoE adapter provides power to ports 0 and 1 of the 4-port 10/100 FE switch on the Cisco 880 series routers and ports 0.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-28 OL-16215-10 . see Figure 1-17 and Figure 1-19. (240 VAC. Cisco 880 Series. For the back panels of some of these routers. 20 A U. Statement 1028 Note The Cisco 892FSP utilizes a single 4-pin power connector type. Figure 3-27 shows the pin number assignment of the Cisco 892FSP Power Adapter Connector. Ensure that the protective device is rated not greater than: 120 VAC. Connecting the AC Adapter Warning The device is designed to work with TN power systems. All connections must be removed to de-energize the unit. 16 to 20 A international). Statement 19 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Statement 1005 Warning This unit might have more than one power supply connection.S.Chapter 3 Connecting the AC Adapter Connecting the Router Figure 3-24 Connecting PoE for the Cisco 880 and the Cisco 890 Series Routers 1 4 5 3 2 4 6 231995 2 1 2 3 48-VDC PoE input jack Power cord Power adapter—48 VDC 4 5 6 AC plug 12-VDC input power-jack plug Power adapter—12 VDC The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a 30-W power supply for non-POE-enabled routers or a 60-W power supply for POE-enabled routers. Cisco 860 Series.

Cisco 880 series. follow these steps: Step 1 Connect the router to an AC power outlet as shown in Figure 3-25. or the Cisco 890FSP ISR to an AC power outlet. Cisco 880 Series. Figure 3-25 Connecting the AC Adapter 1 2 4 3 231996 1 2 12-VDC plug Power cord 3 4 Power adapter—12 VDC AC plug Cisco 860 Series.Chapter 3 Connecting the Router Connecting the AC Adapter To connect your Cisco 860 series. see Figure 3-26. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-29 .To connect the Cisco 892FSP router.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-30 284800 343746 3 OL-16215-10 . 897VA. Pin 3 Pin 1 Pin 4 Pin 2 Pin 1 Pin 2 Ground NC 1 Pin 3 Pin 4 +12 V NC 1. and 898EA Power Adapter Connector Pin Assignment . Cisco 880 Series. Cisco 860 Series. 5A 1 2 4 1 2 12-VDC plug Power Adapter Cord 3 4 Power adapter—12 VDC AC Plug Figure 3-27 Cisco 892FSP 896VA. NC = No Connection.Chapter 3 Connecting the AC Adapter Connecting the Router Figure 3-26 Connecting the AC Adapter for the Cisco 892FSP 7 6 G E LA N 5 4 Ci sco 892FSP C O N S O LE G E W AN G E W AN SFP R ESET 9 8 8 AU X 12VD C 2.

slide the clip to the end of the DC plug. attach the power lock clip to the power cord.Chapter 3 Connecting the Router Connecting the AC Adapter Step 2 To secure the power cord to the router. Figure 3-28 Securing the Power Cord 3 2 1 4 1 2 Power lock clip Power cord 3 4 DC plug Lock holes on either side of the power connector Cisco 860 Series. See Figure 3-28. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 270659 3-31 . Cisco 880 Series. and secure the retaining clip into the router chassis.

Do not touch the RJ-11 (phone) port wires (conductors). Connecting an FXS Line Use a standard straight-through RJ-11 modular telephone cable to connect a Foreign Exchange Service (FXS) port to a telephone or fax machine. Statement 1042 Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock. Figure 3-29 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector 1 2 4 3 1 2 Power lock clip Power cord 3 4 Power adapter AC plug Note Figure 3-26 shows how to connect the AC power outlet for the Cisco 892FSP.Chapter 3 Connecting an FXS Line Connecting the Router Step 3 Snap the latches into the holes on either side of the power connector. Warning This equipment contains a ring signal generator (ringer). detach the end away from the unit first. use caution when working near WAN ports. the conductors of a cable connected to the RJ-11 port. Cisco 880 Series. When detaching cables. See Figure 3-29. or the associated circuit-board when the ringer is active. which is a source of hazardous voltage. Statement 1026 Cisco 860 Series. The ringer is activated by an incoming call. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-32 270800 OL-16215-10 .

Statement 1044 To connect the FXS line. Figure 3-30 Connecting an FXS Line 1 2 3 241907 Fax machine or telephone 1 2 Step 2 FXS port RJ-11 cable 3 RJ-11 port Connect the other end of the cable to the RJ-11 port on the fax machine or telephone. follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-33 . Cisco 880 Series. Figure 3-30 shows an FXS line connection. the following ports must be connected through an approved network termination unit with integral circuit protection: FXS.Chapter 3 Connecting the Router Connecting an FXS Line Warning For connections outside the building where the equipment is installed. Cisco 860 Series.

Cisco 860 Series. To avoid electric shock. Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. Figure 3-31 Connecting an FXO Line 2 1 3 270542 1 2 Step 2 FXO port RJ-11 cable 3 Telephone outlet Connect the other end of the RJ-11 cable to a telephone wall outlet. See Figure 3-31. Statement 1026 To connect the FXO line. use caution when working near WAN ports. detach the end away from the unit first. Cisco 880 Series.Chapter 3 Connecting an FXO Line Connecting the Router Connecting an FXO Line Use a straight-through RJ-11 cable to connect the FXO voice port to the PSTN or PBX through a telephone wall outlet. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-34 OL-16215-10 . When detaching cables.

Connecting a Voice ISDN BRI Line Use a straight-through RJ-45 cable to connect the voice BRI port to the ISDN network through a telephone outlet or other device. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-35 . Note When the interface is configured as NT and is connecting to a TE device. To enable the soft-offhook command on the port. use a crossover cable. This option allows a stepped offhook resistance during seizure. To connect the voice BRI line. Cisco 860 Series. See Table A-13. then adjusts to 50 Ohms when ringing voltage is not present.Chapter 3 Connecting the Router Connecting a Voice ISDN BRI Line Note If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX) connection mode for an FXO voice port (with loop resistance less than 8000 Ohm). and to access the connection command with plar opx syntax. Caution To prevent damage to the router. The stepped offhook resistance is initially set to 800 Ohms. be sure to connect the BRI cable to the BRI connector only and not to any other RJ-45 connector. Cisco 880 Series. you must ensure that the soft-offhook option is enabled on the port. which avoids overloading the circuit during offhook in the event that ringing voltage is present on the circuit at the same time as the trunk seizure. follow these steps: Step 1 Connect one end of a straight-through RJ-45–to–RJ-45 cable to the Voice BRI port. see the Cisco Command Lookup Tool.

Figure 3-32 Connecting a Voice BRI Line 1 2 3 241906 1 2 Step 2 Voice BRI port RJ-45 cable 3 Telephone outlet Connect the other end of the cable to the RJ-45 telephone outlet or other device.Chapter 3 Connecting a Voice ISDN BRI Line Connecting the Router Figure 3-32 shows a voice BRI line connection. Cisco 880 Series. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-36 OL-16215-10 .

Keep the optical transmit and receive ports covered whenever a cable is not connected to the port. Statement 1040 Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. magnifiers. or performing procedures other than those specified may result in hazardous radiation exposure. and microscopes) within a distance of 100 mm may pose an eye hazard.Chapter 3 Connecting the Router Connecting a Small Form-Factor Pluggable Module Connecting a Small Form-Factor Pluggable Module This section describes how to connect and remove a small form-factor (SFP) module and contains the following information: • • • • Safety Warnings. Statement 1056 Warning Use of controls. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-37 . Viewing the laser output with certain optical instruments (for example. adjustments. Statement 1016 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Cisco 880 Series. Do not stare into beams or view directly with optical instruments. page 3-38 Online Insertion and Removal. eye loupes. Statement 1051 Warning Do not stare into the laser beam. page 3-39 Safety Warnings Laser Safety Warnings Optical SFPs use a small laser to generate the fiber-optic signal. Statement 1010 Warning Invisible laser radiation present. Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. page 3-38 Removing an SFP Module. Statement 1057 Cisco 860 Series. page 3-37 Installing an SFP Module. Do not view directly with optical instruments.

Do not pull on the cabling in an attempt to remove the SFP. Do not stare into beams or view directly with optical instruments. Cisco 860 Series. Figure 3-33 Installing an SFP Module Caution Step 2 Do not remove the optical port plugs from the SFP until you are ready to connect cabling. Latch designs are not linked to SFP model or technology type. the handle should be on top of the SFP module. follow these steps: Step 1 Slide the SFP into the SFP port connector until it locks into position (see Figure 3-33). Step 2 Note SFP modules use various latch designs to secure the module in the SFP port. see the label on the side of the SFP. Removing an SFP Module Follow these steps to remove the SFP module from a Cisco 892F series router: Step 1 Disconnect all cables from the SFP. Warning Invisible laser radiation may be emitted from disconnected fibers or connectors.Chapter 3 Connecting a Small Form-Factor Pluggable Module Connecting the Router Installing an SFP Module To connect and secure the SFP module. Statement 1051 Caution The latching mechanism used on many SFPs locks the SFP into place when cables are connected. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-38 94126 OL-16215-10 . Connect the network cable to the SFP module. Disconnect the SFP latch. Cisco 880 Series. See Figure 3-34. For information on the SFP technology type and model. Tip If the SFP uses a bale-clasp latch (see Figure 3-33).

the speed is set to 1000 and duplex is set to full. Note If an SFP module is inserted with auto-failover or SFP media-type already configured. screwdriver. For a 1000 base SFP. For a 100 base SFP. Cisco 860 Series. Cisco 880 Series. Step 3 Online Insertion and Removal Online insertion and removal (OIR) of the SFP module is supported on the Cisco 892F ISRs. or other small straight tool to gently release a bale-clasp handle if you cannot reach it with your fingers. Grasp the SFP on both sides and remove it from the router. the port is forced to the speed and duplex capability of the SFP.Chapter 3 Connecting the Router Connecting a Small Form-Factor Pluggable Module Figure 3-34 Figure 5-42 Disconnecting SFP Latch Mechanisms 1 A 2 3 4 B 117722 1 2 Sliding latch Swing and slide latch 3 4 Bale-clasp latch Plastic collar latch Tip Use a pen. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-39 . the speed is set to 100 and duplex can be configured to either half or full.

workstation. LAN 1. Green when the channel is connected. then check the LEDs. workstations. FE2. PCs. Green when service is established. Green when receiving or sending data. Green when a crypto session is running. On when the FE LAN port is physically connected to a server. Green when signal strength is high. or LAN 3 external Ethernet switch connected to the LAN ports (FE01. Fast blinking when signal strength is medium. Green when the line is connected to the xDSL DSLAM3. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-40 OL-16215-10 . see the “LEDs” section on page 1-30. refer to Table 3-3. Off or slow blinking when signal strength is low. Green when EFM mode is selected. PC. Green when ATM mode is selected. Table 3-3 Verifying the Router Operation Power and Link Power LEDs to Check OK Normal Patterns On when power is supplied to the router. or FE3) To FE WAN line To xDSL line 2 WAN FE4 xDSL CD xDSL Data On when the WAN Ethernet carrier has detected status. To verify router operation. Green when the ISDN line is connected. FE1. Green when service is established. or an LAN 2. For the full LED descriptions. Green when either a PPPoE10 or PPPoA11 client is running. first turn on all the connected devices.Chapter 3 Verifying Connections Connecting the Router Verifying Connections To verify that all devices are properly connected to the router. Blinks when receiving or transmitting data. Cisco 880 Series. ATM EFM To ISDN line 898EA only 898EA only Data BRI LNK Data BRI B1 and B2 3G4 WWAN5 RSSI 6 CDMA GSM To PPP clients To VPN12 tunnel 9 8 7 Green when service is established. LAN 0. To servers. or external Ethernet switch. PPP VPN Cisco 860 Series. Blinks when line is in training mode. Slow blinking when searching for service. Amber when service is not established.

Cisco 880 Series.4-GHz status: • • WLAN 5. and signal is being transmitted. SSID is configured.0 GHz Wireless LAN 5. Off if no client is associated. and client is associated. signal is being transmitted. Slow blinking when radio is connected. Green when connected and powered. SSID13 is configured. SSID is configured. Off when the link is down. and client is associated. Slow blinking for 100Base SFPs and fast blinking for 1000Base SFPs. Green when radio is connected. WLAN 2.Chapter 3 Connecting the Router Verifying Connections Table 3-3 Verifying the Router Operation (continued) Power and Link To wireless LAN LEDs to Check WLAN LINK Normal Patterns Wireless LAN link status: • • Green if at least one client is associated. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 3-41 . Slow blinking when radio is connected.0-GHz status: • • PoE14 PoE 0 (880 and 890 series only) PoE 1 (880 and 890 series only) PoE 2 (890 series only) PoE 3 (890 series only) PoE power status: • • SFP15 EN S Green when the interface is up. Green when radio is connected. To LAN GE/FE line LAN (860VAE models only) Cisco 860 Series. signal is being transmitted. Amber when there is a fault with the inline power supply. and signal is being transmitted.4 GHz Wireless LAN 2. SSID is configured. Blinking when there is LAN activity (traffic in either direction). Blinking green indicates port speed.

PoE = Power over Ethernet. VDSL (very-high-data-rate digital subscriber line). VPN = Virtual Private Network. SFP = small-form-factor pluggable. 2. GE ACT On when the GE WAN interface is up. PPP = Point-to-Point Protocol. Blinking when there is DSL WAN activity (traffic in either direction). 7.SHDSL. or no cable attached to DSL connector. 10. 1. Blinking when there is GE WAN activity (traffic in either direction). Faster blinking when there is heavier traffic. 11. 4. and G. 8. 14. Off when the device is powered off or the DSL WAN interface is down. Cisco 880 Series. Off when the device is powered off.Chapter 3 Verifying Connections Connecting the Router Table 3-3 Verifying the Router Operation (continued) Power and Link To DSL line (860VAE models only) LEDs to Check DSL LINK Normal Patterns On when DSL WAN mode is selected and DSL training complete. 12. DSL ACT On when the DSL interface is up. To WAN GE line (860VAE models only) GE Mode On when GE WAN mode is selected. Blinking when DSL WAN mode is selected but incomplete DSL LinkUp state such as in-training (slow initially. 6. CDMA = code division multiple access. SSID = service set identifier. WWAN = wireless WAN. 3. including ADSL (asymmetric digital subscriber line). 5. Off when the device is powered off or when DSL WAN mode is selected. PPPoA = PPP over ATM. or controller "OFF". 15. 3G = Third-Generation. DSLAM = digital subscriber line access multiplexer. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 3-42 OL-16215-10 . FE = Fast Ethernet. GSM = Global System for Mobile Communications. xDSL = General term referring to various forms of DSL. Off when the device is powered off or when the GE WAN interface is down. PPPoE = PPP over Ethernet. Cisco 860 Series. 9. or GE WAN mode is selected. RSSI = Received Signal Strength Indicator. 13. fast when almost connected).

CH A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco 860 series. you must set up a console connection. Cisco 860 Series. For instructions on how to set up a console connection. For instructions on how to use Cisco CP Express to configure the router see Cisco CP Express User’s Guide. the setup command facility prompts you for basic information about your router and network. 880 series. we recommend using Cisco Configuration Professional (CP) Express. go to the “Setup Command Facility” section on page 3 to configure the initial router settings. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 4-1 . and 890 series Integrated Services Routers (ISRs). we recommend that you use the Cisco CP Express web-based application to configure the initial router settings. For the initial configuration. page 4-1 Setup Command Facility. page 4-5 Initial Configuration of the Wireless Access Point. Cisco 880 Series. page 4-1 Cisco IOS CLI. If your router does not have a default configuration file. To create the initial configuration. see the “Connecting a Terminal or PC to the Console Port” section on page 3-9. page 4-6 Note Some SKUs may not include a default configuration file. Cisco CP Express is a web-based graphical user interface that guides you through initial configuration. page 4-3 Verifying the Initial Configuration. Cisco IOS CLI To configure the initial router settings by using the Cisco IOS CLI. Cisco Configuration Professional Express After you connect the cables and power up the router. You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility. This chapter contains the following sections: • • • • • Cisco Configuration Professional Express.

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 4-2 OL-16215-10 . The following prompt is displayed: Router# A message is displayed that is similar to the first warning message. Note You must change the username and password before you log off the router.Chapter 4 Cisco IOS CLI Initial Configuration To configure the initial router settings using the Cisco IOS CLI. You are now in privileged EXEC mode... router con0 is now available Step 2 Press Return.. Cisco 860 Series. You cannot use the username username1 or password password1 after you log off from this session. Here are the Cisco IOS commands." The default username and password have a privilege level of 15.. follow these steps: Step 1 Set up a console connection to your router. . see the applicable configuration procedures in Cisco 860 Series. User Access Verification Username: Step 3 Enter the username username1. and press Return or Enter. The message directs you to change the username and password.. Cisco 880 Series. Router# Router#config t Router(config)# Router(config)#username username privilege 15 secret 0 password Step 6 To change the username and password. The following prompt is displayed: Password: Step 4 Enter the password password1. For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router.. Step 5 Enter configuration mode using the following commands. and Cisco 890 Series Integrated Services Routers Software Configuration Guide. The following message is displayed: Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. username <myuser> privilege 15 secret 0 <mypassword> no username username1 Replace <myuser> and <mypassword> with the username and password you want to use. To continue using the Cisco IOS CLI for initial configuration. and press Return or Enter. The following message is displayed: . Please change these publicly known initial credentials using Cisco CP Express or the Cisco IOS CLI. This feature requires the one-time use of the username "username1" with the password "password1. enter the following at the prompt: username username privilege 15 secret 0 password The username and password are the username and password that you determine. Cisco 880 Series.

Chapter 4

Initial Configuration Setup Command Facility

Note

Save your configuration changes regularly to avoid losing them during resets, power cycles, or power outages. Use the copy running-config startup-config command at the privileged EXEC mode prompt (Router#) to save the configuration to NVRAM.

Step 7

Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.

Setup Command Facility
The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network. To use the setup command facility, you must set up a console connection with the router and enter the privileged EXEC mode.

Note

For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to the Console Port” section on page 3-9.

To configure the initial router settings by using the setup command facility, follow these steps:
Step 1 Step 2

Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how to enter privileged EXEC mode, see Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1. In privileged EXEC mode, at the prompt, enter setup.
yourname# setup

The following message is displayed:
--- System Configuration Dialog --Continue with configuration dialog? [yes/no]:

You are now in the setup command facility. The prompts in the setup command facility vary, depending on your router model, on the installed interface modules, and on the software image. The following steps and the user entries (in bold) are shown as examples only.

Note

If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC mode prompt (Router#). For more information on using the setup command facility, see “The Setup Command” chapter in Cisco IOS Configuration Fundamentals Command Reference, Release 12.2T.

Step 3

To proceed using the setup command facility, enter yes.
Continue with configuration dialog? [yes/no]: yes

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10

4-3

Chapter 4 Setup Command Facility

Initial Configuration

Step 4

When the following messages appear, enter yes to enter basic management setup.
At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes

Step 5

Enter a hostname for the router (this example uses Router).
Configuring global parameters: Enter host name [Router]: Router

Step 6

Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration.
The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: xxxxxx

Step 7

Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration.
The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: xxxxxx

Step 8

Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port.
The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: xxxxxx

Step 9

Respond to the following prompts as appropriate for your network.
Configure SNMP Network Management? [yes]: Community string [public]:

A summary of the available interfaces is displayed.
Step 10

Choose one of the available interfaces for connecting the router to the management network.
Enter interface name used to connect to the management network from the above interface summary: fastethernet4

Step 11

Respond to the following prompts as appropriate for your network.
Configuring interface FastEthernet4: Use the 100 Base-TX (RJ-45) connector? [yes]: yes Operate in full-duplex mode? [no]: yes Configure IP on this interface? [yes]: yes IP address for this interface: 172.1.2.3 Subnet mask for this interface [255.255.0.0] : 255.255.0.0 Class B network is 172.1.0.0, 26 subnet bits; mask is /16

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

4-4

OL-16215-10

Chapter 4

Initial Configuration Verifying the Initial Configuration

The configuration is displayed:
The following configuration command script was created: hostname Router enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-server community public ! no ip routing ! interface FastEthernet4 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 !

Step 12

Respond to the following prompts. Enter 2 to save the initial configuration.
[0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! RETURN The user prompt is displayed. Router>

Step 13

Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5 for verification procedures.

After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional configuration.

Verifying the Initial Configuration
To verify that the new interfaces are operating correctly, perform the following tests:
• • •

To verify that the interfaces and line protocol are in the correct state—up or down—enter the show interfaces command. To display a summary status of the interfaces configured for IP, enter the show ip interface brief command. To verify that you configured the correct hostname and password, enter the show configuration command.

After you complete and verify the initial configuration, you can configure your Cisco router for specific functions.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10

4-5

Chapter 4 Initial Configuration of the Wireless Access Point Initial Configuration Initial Configuration of the Wireless Access Point The embedded wireless access point (AP) runs its own IOS. and Cisco 890 Series Integrated Services Routers Software Configuration Guide. Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide 4-6 OL-16215-10 . Cisco 880 Series. You can initially configure the embedded wireless AP by using one of the following methods: • • Cisco Configuration Professional (CP) Express Setup command facility on the embedded wireless device For information on how to do basic wireless configuration on your router see the “Basic Wireless Device” chapter of the Cisco 860 Series. Cisco 880.

Cisco 880 Series. page A-5 VDSL2 Port Connector Pinouts.92 Port Connector Pinouts. and Cisco 890 series Integrated Services Routers (ISRs). Statement 1040 Note For compliance and safety information. Cisco 860 Series.A P P E N D I X A Technical Specifications This appendix provides router. It contains the following sections: • • • • • • • • • • • • • Router Specifications.SHDSL Port Connector Pinouts. Cisco 880 series. page A-7 SFP Port Connector Pinouts. page A-7 Voice ISDN BRI Interface Pin Numbers and Functions. page A-6 G. and cabling specifications for the Cisco 860 series. port. page A-2 Wireless Access Point. see Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. page A-5 ADSL2+ Port Connector Pinouts. page A-6 Data BRI Port Connector Pinouts. page A-3 Console and Auxiliary Port Connector Pinouts. page A-5 V. page A-8 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. page A-3 FE and GE Port Pinouts. page A-8 Cable Specifications. page A-4 FXS and FXO Port Connector Pinouts. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 A-1 .

8 x 10. Cisco 880 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-2 OL-16215-10 .000 ft (4570 m) 32 to 104°F (0 to 40°C) 0 to 10.000 ft (3000 m) N/A. 3 lb (1. maximum Design Specification Cisco 860VAE series 1.000 ft (3000 m) 10 to 85% relative humidity 10 to 85% relative humidity Cisco 860 Series. no fan N/A. maximum +12 VDC Low speed 31. Table A-1 Router Specifications Description Physical Dimensions Dimensions with antenna and rubber feet (H x W x D) Weight (not including desktop power supply) Design Specification (all models except Cisco 860VAE series) 1.1 dBa Low speed 38.5 kg).Appendix A Router Specifications Technical Specifications Router Specifications Table A-1 lists the system specifications for the routers.4 kg) The total weight depends on customer-selected options. no fan Environmental Operating Ranges Nonoperating temperature Nonoperating humidity Nonoperating altitude Operating temperature Operating humidity Operating altitude Acoustic Acoustic: Sound Pressure (Typical/Maximum) Acoustic: Sound Power (Typical/Maximum) Router Power Adapter Input voltage Input frequency Power output Output voltages Inline Power-over-Ethernet Adapter Input voltage Input frequency Power output Output voltage 85 to 264 VAC 47 to 63 Hz 80 W.75 x 9. 5.5 x 9 in.000 ft (4570 m) 32 to 104°F (0 to 40°C) 0 to 10.9 dBA High speed 51.5 lb (2. –4 to 149°F (–20 to 65°C) 5 to 95% relative humidity 0 to 15. maximum –48 VDC not supported 100 to 240 VAC Nominal 47 to 63 Hz 60 W.7 dBa –4 to 149°F (–20 to 65°C) 5 to 95% relative humidity 0 to 15.4 dBa High speed 44.4 in. maximum +12 VDC 100 to 240 VAC Nominal 47 to 63 Hz 30 W.9 x 12.

Table A-2 Wireless Access Point Specifications Description Radio technology Design Specification IEEE 802. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 A-3 . FE and GE Port Pinouts Table A-3 describes the RJ-45 connector pinouts for Fast Ethernet (FE) ports with Power over Ethernet (PoE).4 and 5-GH radio bands Channels PHY Data rate Country-specific 20 and 40 MHz 802. 1.11g up to 54 Mb/s 802.3af-compliant devices connected to FE ports 0. 2.11n up to 300 Mb/s 1. Cisco 880 Series. Cisco 860 series and 880 series ISRs Operating frequency 2.11n draft 2. For ports that do not support PoE. and 3. 5. • • • Cisco 860VAE and 860VAE-K9 ISRs do not support PoE. and 8 are not connected.11b up to 11 Mb/s 802. 2x3 MIMO1 radio. pins 4.3af-compliant devices connected to FE ports 0 and 1. Some models support PoE using an optional module. Backward compatible with 802.11a (Cisco 890 series routers). Ethernet FE LAN Port Pinouts Table A-3 Pin 1 2 3 4 5 6 7 8 Function RX+1 RX– TX+2 PoE—optional PoE—optional TX– PoE—optional PoE—optional Cisco 860 Series.11b/g and 802. MIMO = Multiple Input/Multiple Output. 7.0 standard compliant.Appendix A Technical Specifications Wireless Access Point Wireless Access Point Table A-2 lists the specifications for the wireless access point (AP). Cisco 880 series ISRs can include an optional PoE module that provides power to 802. Cisco 890 series ISRs can include an optional PoE module that provides power to 802. and some models do not support PoE.4-GHz radio band Cisco 890 series ISRs 2.

RX = Receive 2. RX = Receive GE Signal (LAN and WAN) Tx A+1 Tx ARx B+2 Tx C+ Tx CRx BRx D+ Rx D- Console and Auxiliary Port Connector Pinouts Table A-5 lists the pinouts for the console and auxiliary port connectors. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-4 OL-16215-10 . TX = Transmit 2. Table A-5 Console and Auxiliary Port Connector Pinouts RJ-45 Pin 1 2 3 4 5 6 7 8 Function RTS DTR TXD GND GND RXD DSR CTS Cisco 860 Series.Appendix A Console and Auxiliary Port Connector Pinouts Technical Specifications 1. TX = Transmit Table A-4 describes the RJ-45 connector pinouts for the Gigabit Ethernet (GE) ports of the Cisco 860VAE and 860VAE-K9 ISRs. Table A-4 Ethernet GE Port Pinouts Pin 1 2 3 4 5 6 7 8 1. Cisco 880 Series.

Appendix A Technical Specifications FXS and FXO Port Connector Pinouts FXS and FXO Port Connector Pinouts Table A-6 lists the FXS and FXO connector pinouts. Table A-7 VDSL2 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin 1 2 3 4 5 6 Function Unused Unused TIP RING Unused Unused ADSL2+ Port Connector Pinouts Table A-8 lists the ADSL2+ connector pinouts. Table A-8 ADSL2+ Connector Pinouts (RJ-11) RJ-11 Pin 1 2 3 4 5 6 Function Unused Unused TIP RING Unused Unused Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 A-5 . Cisco 880 Series. Table A-6 FXS and FXO Connector Pinouts (RJ-11-to-RJ-45) Pin 1 2 3 4 5 6 Signal NC NC TIP RING NC NC VDSL2 Port Connector Pinouts Table A-7 lists the VDSL2 connector pinouts.

SHDSL WAN Port Pinouts for Two-Pair Products Table A-10 Pin 1 2 3 4 5 6 Function Unused TIP (Port1) TIP (Port0) RING (Port0) RING (Port1) Unused Table A-11 lists the pinouts for the symmetrical high-speed DSL (G.92 Connector Pinouts (RJ-11-to-RJ-45) RJ-11 Pin 1 2 3 4 5 6 Function Unused Unused TIP RING Unused Unused G.SHDSL WAN Port Pinouts for Four-Pair Products Table A-11 Pin 1 2 3 Function TIP (Port1) RING (Port1) TIP (Port2) Cisco 860 Series. Cisco 880 Series. Table A-9 V.SHDSL Port Connector Pinouts Table A-10 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) WAN port for four-pair products. including the following router model(s): • C888 G..SHDSL) WAN port for two-pair products.Appendix A V.92 connector pinouts. including the following router models: • • • C888E C888EW C888EA G.92 Port Connector Pinouts Table A-9 lists the V.92 Port Connector Pinouts Technical Specifications V. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-6 OL-16215-10 .

SHDSL WAN Port Pinouts for Four-Pair Products (continued) Pin 4 5 6 7 8 Function TIP (Port0) RING (Port0) RING (Port2) TIP (Port3) RING (Port3) Data BRI Port Connector Pinouts Table A-12 lists the pinouts for the Data BRI port. 2. Table A-13 Interface Pin Numbers and Functions ISDN BRI NT/TE Card Pin 3/T+ Pin 4/R+ Pin 5/RPin 6/T- NT Interface1 Pin 3/R+ Pin 4/T+ Pin 5/TPin 6/R- TE Interface2 Pin 3/T+ Pin 4/R+ Pin 5/RPin 6/T- 1.Appendix A Technical Specifications Data BRI Port Connector Pinouts Table A-11 G. Use a crossover cable for TE interfaces. Cisco 880 Series. Cisco 860 Series. Table A-12 Data BRI Port Pinouts Pin 1 2 3 4 5 6 7 8 Function Unused Unused TXP RXP TXN TXN Unused Unused Voice ISDN BRI Interface Pin Numbers and Functions Table A-13 lists the interface pin numbers and functions for the voice ISDN BRI port. Use a straight-through cable for NT interfaces. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 A-7 .

Cisco 880 Series. Cisco 860 Series. Table A-14 SFP Port Pinouts Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Function TX Ground TX Fault TX disable Module definition 2 Module definition 1 Module definition 0 Rate Select Loss of signal Receiver ground Receiver ground Receiver ground Inverted received data out Received data out Receiver ground Receiver power Transmitter power Transmitter ground Transmit data in Inverted transmit data in Transmitter ground Cable Specifications This section provides specifications for the following Ethernet cables: • • Straight-through cable Crossover cable Because of the autocrossover (autosensing) function. both straight-through and crossover cables can be used for the Ethernet LAN port.Appendix A SFP Port Connector Pinouts Technical Specifications SFP Port Connector Pinouts Table A-14 lists the pinouts for the SFP port. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-8 OL-16215-10 .

and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16215-10 A-9 . Cisco 880 Series.Appendix A Technical Specifications Cable Specifications Ethernet Cable Specifications Table A-15 lists the specifications that apply to both straight-through and crossover Ethernet cables. This length is also the maximum distance between the router and the equipment connected to it. Table A-15 Ethernet Cable Specifications Type 10BASE-T 100BASE-T 1000BASE-T Category Category 3 or 5 Category 5 or higher Category 5 or higher Maximum Cable Length The maximum length for the Ethernet cables that connect equipment to the router is 328 feet (100 meters). Cisco 860 Series.

Appendix A Cable Specifications Technical Specifications Cisco 860 Series. and Cisco 890 Series Integrated Services Routers Hardware Installation Guide A-10 OL-16215-10 . Cisco 880 Series.