You are on page 1of 10

1

Refer to the exhibit. Switches DSw1 and DSw2 are configured with the HSRP virtual IP address 10.10.10.1, and standby priority is set to
100. Assume both switches finish booting at the same time and HSRP is operating as expected. On the basis of this information, which
three HSRP statements are true? (Choose three.)

Configuring the standby 32 timers 10 30 command on the Gi0/2 interfaces of each switch would decrease the failover time.

If the DSw1 and DSw2 switches have been configured to preempt, then DSw2 will be the active router.

If the DSw1 switch is configured with the standby preempt command and DSw2 is not, then DSw1 will be the active router.

The HSRP group number in this HSRP configuration is HSRP group number 50.

The standby track command is useful for tracking interfaces that are not configured for HSRP.

When Host A sends an ARP request for 10.10.10.1, the Virtual Router replies with the MAC address of the active router.

2 In a network where HSRP is properly configured, what MAC address and IP address will be associated by the end devices with their
default gateway?

the MAC and IP address of the standby router

the MAC and IP address of the backup router

4 .20. The last two digits of the virtual MAC address are derived from the HSRP group identifier. Given the output generated by the show standby command. The standby virtual MAC address is the MAC address of the router with IP address 172. the MAC and IP address of the active router the IP address of the virtual router and the MAC address of the active router the MAC and IP address of the virtual router 3 Refer to the exhibit.) Interface VLAN1 was configured with the standby 1 priority 105 preempt command. The hello and holdtime timers are set at the default values.138. This switch is next in line to become the active HSRP router on VLAN1. which three statements are true? (Choose three.35.

.

7 Which two statements are true regarding Hot Standby Router Protocol (HSRP)? (Choose two. The priority value of 0 means the router has stopped participating in VRRP. GLBP provides load balancing over multiple routers (gateways) . By making use of a single virtual IP address and multiple virtual MAC addresses. and learn states. listen. By making use of a single virtual IP address and multiple virtual MAC addresses. HSRP provides load balancing over multiple routers (gateways). By making use of a single virtual IP address and multiple virtual MAC addresses. All routers in the virtual router group participate in forwarding packets. and speak states. VRRP provides load balancing over multiple routers (gateways). The priority value of 0 means the router is ineligible to become the master router.5 Which statement is true about Virtual Router Redundancy Protocol (VRRP)? The priority value of 255 means the router is ineligible to become the master router. The priority value of 255 means the router has stopped participating in VRRP. listen. .) A router will remain in the speak state unless it becomes an active or standby router. All routers in the virtual router group participate in forwarding packets. All routers in the virtual router group participate in forwarding packets. One member is elected to be the active router for the group and the other routers are passive until the active router fails. 6 Of the gateway redundancy protocols that are mentioned. The first three HSRP states are the initial. which statement is true? GLBP allows multiple routers to participate in a virtual router group that is configured with a virtual IP address. The first three HSRP states are the initial.

GLBP will attempt to balance traffic on a per-host basis by the use of the round-robin algorithm. router redundancy is required. The active virtual gateway (AVG) is the backup for the AVF. . 8 In a new network design.) GLBP will attempt to balance traffic on a per-router basis by the use of the round-robin algorithm. it replies with the MAC address of the interface. When a router that is in active state receives an ARP request for the IP address of the virtual router. Which protocol should be implemented to achieve a redundant configuration? Proxy ARP HSRP VRRP VRSP GLRP 9 What are two characteristics of Gateway Load Balancing Protocol (GLBP) operation? (Choose two. One of the routers to be used for redundancy is not a Cisco router. There can be more than one router in the HSRP group that is in standby state. it replies with the virtual router MAC address. The active virtual forwarder (AVF) is assigned a virtual MAC address and forwards packets sent to that MAC address. When a router that is in active state receives an ARP request for the IP address of the virtual router.

10 Refer to the exhibit. Router A will take over as active.16.0.104.0. GLBP members communicate with each other through hello messages sent every 3 seconds to the multicast address 224. The priority value for HSRP group 1 is the default value. If the active router for HSRP group 2 goes. 11 How does an HSRP enabled router update its holdtime? group numbers hello messages priority settings standby commands 12 . down. The priority value for HSRP group 2 is the default value. Traffic sharing is being performed on two routers.120. Router A will respond to ARP requests for IP address 172. Which two statements are true? (Choose two).10.

0.0.0.0. Interface VLAN 1 was configured with the standby priority 105 command. The IP address 10.0.) Interface VLAN 1 was configured with the standby ip 10. The hellotime and holdtime are set to their default values.0. Refer to the exhibit.1 command.35 is configured on the Sw1 device.1 command. 13 . Which two statements regarding the Hot Standby Router Protocol are true? (Choose two. Interface VLAN 1 was configured with the standby 100 ip 10.

The switch has priority 50 configured without the preempt option. The switch has priority 50 configured with the preempt option. The switch has become the active HSRP router. What two pieces of information can be gleaned from the debug standby command output? (Choose two. The switch has become the standby HSRP router. 14 . Refer to the exhibit. The switch has priority 100 configured with the preempt option.) The switch has priority 100 configured without the preempt option.

which router will become an active router when the current active router R1 goes down? Router R2 will become active because the standby preempt command is configured on this router. . On the basis of the configurations that are provided. HSRP has been configured on the network for redundancy.Refer to the exhibit. Router R2 will become active because it has the lowest configured IP address. Router R4 will become active because it has the highest IP address that is configured. Router R3 will become active because it has the highest priority value that is configured.

which router responds to an ARP request from a host looking for its default-gateway MAC address? active virtual forwarder active virtual gateway active wirtual router master virtual forwarder master virtual gateway master virtual router Max Points: 32 Earned Points: 27 Percentage: 84.15 In GLBP operation.4% .