You are on page 1of 8

Cisco- 300-135-Troubleshooting and

Maintaining Cisco IP Networks
(TSHOOT)
Pass Cisco 300-135 exam with 100%
Guarantee
100% REAL EXAM QUESTIONS ANSWERS
Get All PDF with Complete Questions Answers File from

http://www.pass4sureexam.co/300-135.html
100% Exam Passing Guarantee & Money Back Assurance

Sample Questions

QUESTION: 1
Exhibit:

A network administrator is troubleshooting an EIGRP connection
between RouterA, IP address 10.1.2.1, and RouterB, IP address
10.1.2.2. Given the debug output on RouterA, which two statements
are true? (Choose two.)

A.
B.
C.
D.

RouterA received a hello packet with mismatched autonomous system numbers.
RouterA received a hello packet with mismatched hello timers.
RouterA received a hello packet with mismatched authentication parameters.
RouterA received a hello packet with mismatched metric-calculation
mechanisms.
E. RouterA will form an adjacency with RouterB.
F. RouterA will not form an adjacency with RouterB.

Answer: DF

Question: 2
When troubleshooting an EIGRP connectivity problem, you notice that two
connected EIGRP routers are not becoming EIGRP neighbors. A ping between the
two routers was successful. What is the next thing that should be checked?
A. Verify that the EIGRP hello and hold timers match exactly.
B. Verify that EIGRP broadcast packets are not being dropped between the two
routers with the show ip EIGRP peer command.
C. Verify that EIGRP broadcast packets are not being dropped between the two
routers with the show ip EIGRP traffic command.
D. Verify that EIGRP is enabled for the appropriate networks on the local and
neighboring router.
Answer: D

Question: 3
Refer to the exhibit.

How would you confirm on R1 that load balancing is actually occurring on the
default-network (0.0.0.0)?

A. Use ping and the show ip route command to confirm the timers for each default
network resets to 0.
B. Load balancing does not occur over default networks; the second route will only
be used for failover.
C. Use an extended ping along with repeated show ip route commands to confirm
the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing
table.
Answer: D

Question: 4
Which IPsec mode will encrypt a GRE tunnel to provide multiprotocol support
and reduced overhead?
A.
B.
C.
D.

3DES
multipoint GRE
tunnel
transport

Answer: D

Question: 5
Which three features are benefits of using GRE tunnels in conjunction with IPsec
for building site-to-site VPNs? (Choose three.)
A.
B.
C.
D.

B. supports multi-protocol (non-IP) traffic over the tunnel
reduces IPsec headers overhead since tunnel mode is used
simplifies the ACL used in the crypto map
uses Virtual Tunnel Interface (VTI) to simplify the IPsec VPN configuration

Answer: ABD

Question: 6
Which statement is true about an IPsec/GRE tunnel?
A. The GRE tunnel source and destination addresses are specified within the IPsec
transform set.
B. An IPsec/GRE tunnel must use IPsec tunnel mode.
C. GRE encapsulation occurs before the IPsec encryption process.
D. Crypto map ACL is not needed to match which traffic will be protected.
Answer: C

Question: 7
The implementations group has been using the test bed to do a `proof-of-concept'
that requires both Client 1 and Client 2 to access the WEB Server at
209.65.200.241. After several changes to the network addressing, routing scheme,
DHCP services, NTP services, and FHRP services, a trouble ticket has been
operated indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to Isolated the cause of this fault and answer the
following questions. On which device is the fault condition located?
A.
B.
C.
D.
E.
F.
G.
H.

R1
R2
R3
R4
DSW1
DSW2
ASW1
ASW2

Answer: G

Question: 8
The implementations group has been using the test bed to do a `proof-of-concept'
that requires both Client 1 and Client 2 to access the WEB Server at
209.65.200.241. After several changes to the network addressing, routing scheme,
DHCP services, NTP services, and FHRP services, a trouble ticket has been
opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the
following questions.
The fault condition is related to which technology?
A.
B.
C.
D.
E.
F.

NTP
Switch-to-Switch Connectivity
Access Vlans
Port Security
VLAN ACL / Port ACL
Switch Virtual Interface

Answer: B

Question: 9
The implementations group has been using the test bed to do a
`proof-of-concept' that requires both Client 1 and Client 2 to access
the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing scheme,
DHCP services, NTP services, and FHRP services, a trouble ticket has
been opened indicating that Client 1 cannot ping the 209.65.200.241
address.
Use the supported commands to isolated the cause of this fault and
answer the following questions.
What is the solution to the fault condition?

A. In Configuration mode, using the interface port-channel 13 command, then configure
switchport trunk allowed vlan none followed by switchport trunk allowed vlan 20,200
commands.
B. In Configuration mode, using the interface port-channel 13, port-channel 23, then
configure switchport trunk none allowed vlan none followed by switchport trunk
allowed vlan 10,200 commands.
C. In Configuration mode, using the interface port-channel 23 command, then
configure switchport trunk allowed vlan none followed by switchport trunk allowed
vlan 20,200 commands.
D. In Configuration mode, using the interface port-channel 23, port-channel, then
configure switchport trunk allowed vlan none followed by switchport trunk allowed
vlan 10,20,200 commands.
Answer: B

Question: 10
The implementations group has been using the test bed to do a `proof-of-concept'
that requires both Client 1 and Client 2 to access the WEB Server at
209.65.200.241. After several changes to the network addressing, routing scheme,
DHCP services, NTP services, layer 2 connectivity, FHRP services, and device
security, a trouble ticket has been opened indicating that Client 1 cannot ping the
209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the
following questions.
The fault condition is related to which technology?
A.
B.
C.
D.
E.
F.

NTP
Switch-to-Switch Connectivity
Access Vlans
Port Security
VLAN ACL / Port ACL
Switch Virtual Interface

Answer: D

Buy Complete Questions Answers File from

100% Exam Passing Guarantee & Money Back Assurance
 PDF Version + Test Engine Software Version
 60 Days Free Updates Service
 Valid for All Countries

 Full 100% Money Back Guarantee
 100% Latest pass4sure 300-135 Dumps
 Cisco 300-135 CCNP Routing and Switching Questions and
Answers
 6 Months Cisco Exam Update
 Cisco 300-135 Pass4sure Passing Guarantee

http://www.pass4sureexam.co/300-135.html